Influence of Austenitization Parameters on the Precipitation Sequence and the Chemical Homogenization of Austenite in a High-Performance Fe–Ni–Cr–Al–Ti–Mo Stainless Maraging Steel
Source abstract
Abstract
MLX19 stainless maraging steel grade exhibits a mechanical strength/fracture toughness balance within the required range for landing gear applications. However, the microstructure after the heat treatment still needs to be precisely controlled to obtain a better repeatability of the mechanical properties. This work shows that austenitizing is a critical stage. The influence of austenitization treatment parameters on the microstructure obtained after quenching was thus precisely quantified. It was first revealed that, after a standard austenitization at 850 °C and for specific heating rates and holding times, undissolved β-NiAl precipitates, reaching sizes up to 500 nm, still remain in the as-quenched state, in addition to a high retained austenite fraction. It was also found that large amounts of retained austenite are the result of local heterogeneities in the chemical composition of the austenitic phase prior to quenching, while the undissolved precipitates change the overall chemical composition of the austenitic matrix. New austenitization conditions were thus proposed, leading to a better homogeneity of the chemical composition of the martensitic matrix after quenching.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. S. Floreen: Metall. Rev., 1968, vol. 13, pp. 115–28.10.1179/imr.1968.13.1.115 ↗
2. W. Sha and Z. Guo: Maraging Steels. Modelling of Microstructure, Properties and Applications. Woodhead Publishing Limited, Oxford, 2009.
3. W. Sha, H. Leitner, Z. Guo, and W. Xu: Phase Transformations in Steels—Volume 2: Diffusionless Transformations, High strength Steels, Modelling and Advanced Analytical Techniques. Woodhead Publishing Limited, Oxford, 2012, pp. 332–262.10.1533/9780857096111.2.332 ↗
4. F. Roch: Trait. Therm., 2008, vol. 390, pp. 51–8.
5. R. Schnitzer, R. Radis, M. Nöhrer, M. Schober, R. Hochfellner, S. Zinner, E. Povoden-Karadeniz, E. Kozeschnik, and H. Leitner: Mater. Chem. Phys., 2010, vol. 122, pp. 138–45.10.1016/j.matchemphys.2010.02.058 ↗
6. C.H. Beraldo, J.W. Calderón-Hernández, R. Magnabosco, and N. Alonso-Falleiros: Mater. Res., 2019, vol. 22, pp. 1–9.
7. S. Ifergane, M. Pinkas, Z. Barkay, E. Brosh, V. Ezersky, O. Beeri, and N. Eliaz: Mater. Charact., 2017, vol. 127, pp. 129–36.10.1016/j.matchar.2017.02.023 ↗
8. C. Le Nué: Étude de la relation microstructure/ténacité d'aciers maraging inoxydables. PhD Thesis. Université de Toulouse, 2017.
9. C. Le Nué, J.M. Cloué, M.H. Mathon, S. Puech, D. Béchet, and D. Delagnes: Mater. Sci. Forum., 2016, vol. 879, pp. 413–8.10.4028/www.scientific.net/MSF.879.413 ↗
10. H. Nakagawa and T. Miyazaki: J. Mater. Sci., 1999, vol. 34, pp. 3901–8.10.1023/A:1004626907367 ↗
11. U.K. Viswanathan, T.R.G. Kutty, and C. Ganguly: Metall. Trans. A., 1993, vol. 24A, pp. 2653–6.10.1007/BF02659489 ↗
12. M.K. El-Fawkhry, M. Eissa, A. Fathy, and T. Mattar: in Materials Today: Proceedings, vol. 2, Elsevier, 2015, pp. S711–14.10.1016/j.matpr.2015.07.381 ↗
13. D. Boussaid: Université de Lorraine, 2018.
14. R. Bhambroo, S. Roychowdhury, V. Kain, and V.S. Raja: Mater. Sci. Eng. A., 2013, vol. 568, pp. 127–33.10.1016/j.msea.2013.01.011 ↗
15. H. Leitner, M. Schober, and R. Schnitzer: Acta Mater., 2010, vol. 58, pp. 1261–9.10.1016/j.actamat.2009.10.030 ↗
16. H. Leitner, R. Schnitzer, M. Schober, and S. Zinner: Acta Mater., 2011, vol. 59, pp. 5012–22.10.1016/j.actamat.2011.04.053 ↗
17. S.D. Erlach, H. Leitner, M. Bischof, H. Clemens, F. Danoix, D. Lemarchand, and I. Siller: Mater. Sci. Eng. A., 2006, vol. 429, pp. 96–106.10.1016/j.msea.2006.05.071 ↗
18. T.H. Simm, L. Sun, D.R. Galvin, E.P. Gilbert, D. Alba Venero, Y. Li, T.L. Martin, P.A.J. Bagot, M.P. Moody, P. Hill, H.K.D.H. Bhadeshia, S. Birosca, M.J. Rawson, and K.M. Perkins: Mater. Sci. Eng. A., 2017, vol. 702, pp. 414–24.10.1016/j.msea.2017.07.013 ↗
19. L. Sun, T.H. Simm, T.L. Martin, S. McAdam, D.R. Galvin, K.M. Perkins, P.A.J. Bagot, M.P. Moody, S.W. Ooi, P. Hill, M.J. Rawson, and H.K.D.H. Bhadeshia: Acta Mater., 2018, vol. 149, pp. 285–301.10.1016/j.actamat.2018.02.044 ↗
20. M. Thuvander, M. Andersson, and K. Stiller: Ultramicroscopy., 2013, vol. 132, pp. 265–70.10.1016/j.ultramic.2012.10.014 ↗
21. E. Pereloma and D. Edmonds: Phase Transformations in Steels—Volume 1: Fundamentals and Diffusion-Controlled Transformations. Woodhead Publishing, Oxford, 2012.10.1533/9780857096104 ↗
22. W. Sha, H. Leitner, Z. Guo, and W. Xu: Phase Transformations in Steels—Volume 2: Diffusionless Transformations, High Strength Steels, Modelling and Advanced Analytical Techniques. Woodhead Publishing, Oxford, 2012.
23. L.T. Shiang and C.M. Wayman: Metallography., 1988, vol. 21, pp. 399–423.10.1016/0026-0800(88)90004-3 ↗
24. L.T. Shiang and C.M. Wayman: Metallography., 1988, vol. 21, pp. 425–51.10.1016/0026-0800(88)90005-5 ↗
25. J. Bridge and G. Maniar: in Metallography as a Quality Control Tool, J.L. McCall and P.M. French, eds., Plenum Press, New York, 1980, pp. 279–95.
26. J.M. Cloué, B. Viguier, and E. Andrieu: Metall. Mater. Trans. A., 2005, vol. 36A, pp. 2633–9.10.1007/s11661-005-0261-6 ↗
27. R. Schnitzer, S. Zinner, and H. Leitner: Scr. Mater., 2010, vol. 62, pp. 286–9.10.1016/j.scriptamat.2009.11.020 ↗
28. A. Mondelin, M. Coret, E. Feulvarch, and J. Rech: in 20ème Congrès Français de Mécanique, 2011, pp. 1–6.
29. R. Kapoor and I.S. Batra: Mater. Sci. Eng. A., 2004, vol. 371, pp. 324–34.10.1016/j.msea.2003.12.023 ↗
30. L.G. de Carvalho, M.S. Andrade, R.L. Plaut, F.M. Souza, and A.F. Padilha: Mater. Res., 2013, vol. 16, pp. 740–4.10.1590/S1516-14392013005000069 ↗
31. R. Cozar: Trait. Therm., 1982, (165), pp. 63–71.10.2307/816668 ↗
32. S. Floreen and R.F. Decker: Trans. ASM., 1962, vol. 55, p. 519.
33. H. Hou, H. Li, Y. Jin, X. Wang, and Z. Wen: Mater. Sci. Eng. A., 2014, vol. 601, pp. 1–6.10.1016/j.msea.2014.02.024 ↗
34. H.M. Rietveld: J. Appl. Crystallogr., 1969, vol. 2, pp. 65–71.10.1107/S0021889869006558 ↗
35. A. Bénéteau: Université de Lorraine, 2018.
36. W.J. Kaluba, T. Kaluba, and R. Taillard: Scr. Mater., 1999, vol. 41, pp. 1289–93.10.1016/S1359-6462(99)00281-X ↗
37. F. Christien, M.T.F. Telling, and K.S. Knight: Mater. Charact., 2013, vol. 82, pp. 50–7.10.1016/j.matchar.2013.05.002 ↗
38. C.R. Hubbard and R.L. Snyder: Powder Diffract., 1988, vol. 3, pp. 74–7.10.1017/S0885715600013257 ↗
39. M. Durand-Charre: La Microstructure Des Aciers et Des Fontes: Genèse et Interprétation. Edp Sciences, Les Ulis, 2012.
40. S. da Silva de Souza, P.S. Moreira, and G.L. de Faria: Mater. Res., 2020, vol. 23, pp. 1–9.
41. S.A. Khan and H.K.D. Bhadeshia: Mater. Sci. Eng. A., 1990, vol. 129, pp. 257–72.10.1016/0921-5093(90)90273-6 ↗