Cracking and Failure Characteristics of Flame Cut Thick Steel Plates
Source abstract
Abstract
Abstract The manufacturing of thick wear-resistant steel plates commonly leads to a layered structure and non-uniform properties in the thickness direction which makes the processing and utilization of the plates problematic. The processing steps of thick plates include flame cutting, which generates a heat-affected zone and high residual stresses into the cut edge. In the worst case, the cutting causes cracking. However, the residual stress level alone is not high enough to break a wear-resistant steel plate that behaves normally. Therefore, high-tensile stress also requires a microstructurally weak factor for crack initiation. For this reason, the main objective of this study is to reveal the main microstructural reasons behind the cracking of plates in flame cutting. To achieve this, plate samples containing cracks are mechanically tested and analyzed by electron microscopy. The results show that cracks are commonly formed horizontally into the tempered region of the heat-affected zone. Cracks initiate in the segregations, which typically have a higher amount of impurity and alloying elements. Increased impurity and alloying content in the segregations decreases the cohesion of the prior austenite grain boundaries. These weakened grain boundaries combined with high-residual tensile stress generate the cracks in the flame-cutting process.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. [1] S. K. Choudhary, S. Ganguly, A. Sengupta, V. Sharma: J. Mater. Process. Technol., 2017, vol. 243, pp. 312-321.10.1016/j.jmatprotec.2016.12.030 ↗
2. [2] N. Yang, C. Su, X. Wang, F. Bai: Journal of Constructional Steel Research, 2016, vol. 122 pp. 213-225.10.1016/j.jcsr.2016.03.014 ↗
3. T. Pikkarainen, V. Vuorenmaa, I. Rentola, M. Leinonen, D. Porter: IOP Conf. Ser. 2016, vol. 117, 012064.10.1088/1757-899X/117/1/012064 ↗
4. [4] Y. Wang, X. Liu, Z. Hu, and Y. Shi: Fatigue Fract. Eng. Mater. Struct., 2013, vol. 36, pp. 1258-1273.10.1111/ffe.12062 ↗
5. [5] Y. Wang, X. Liao, Y. Zhang, and Y. Shi: J. Zhejiang Univ. Sci. A, 2015, vol. 16, pp. 217-228.10.1631/jzus.A1400273 ↗
6. [6] T. Jokiaho, S. Santa-aho, P. Peura, M. Vippola: Metall. Mater. Trans. A, 2019, vol. 50, pp. 4178-4192.10.1007/s11661-019-05314-w ↗
7. T. Jokiaho, S. Santa-Aho, H. Järvinen, M. Honkanen, P. Peura, and M. Vippola: Mater. Perform. Charact., 2018, vol. 7.10.1520/MPC20170083 ↗
8. [8] H. Bhadeshia and R. Honeycombe: Steels: Microstructure and Properties, 4th ed., Butterworth-Heinemann, Oxford, 2017, pp. 217-236.10.1016/B978-0-08-100270-4.00008-1 ↗
9. [9] T. Jokiaho, A. Laitinen, S. Santa-aho, M. Isakov, P. Peura, T. Saarinen, A. Lehtovaara, and M. Vippola: Metall. Mater. Trans. B, 2017, vol. 48, pp. 2891-2901.10.1007/s11663-017-1090-x ↗
10. [10] T. Jokiaho, T. Saarinen, S. Santa-Aho, P. Peura, and M. Vippola: Key Eng. Mater., 2016, vol. 674, pp. 103-108.10.4028/www.scientific.net/KEM.674.103 ↗
11. [11] L. Lindgren, A. Carlestam, and M. Jonsson: J. Eng. Mater. Technol., 1993, vol. 115, pp. 440-44510.1115/1.2904243 ↗
12. G. Krauss: Steels: processing, structure, and performance. Asm International, 201510.31399/asm.tb.spsp2.9781627082655 ↗
13. G. Krauss: Reference Module in Materials Science and Materials Engineering, Elsevier, 2016, pp. 5193–5197.
14. [14] H. Bhadeshia and R. Honeycombe: Steels: Microstructure and Properties, 4th ed., Butterworth-Heinemann, Oxford, 2017, pp. 303-388.10.1016/B978-0-08-100270-4.00011-1 ↗
15. [15] J. C. Han, J. B. Seol, M. Jafari, J. E. Kim, S. J. Seo, C. G. Park: Mater. Charact., 2018, vol. 145, pp. 454-460.10.1016/j.matchar.2018.08.060 ↗
16. [16] A. Karani, S. Koley, M. Shome: Eng. Fail. Anal., 2019, vol. 96, pp. 289-297.10.1016/j.engfailanal.2018.10.018 ↗
17. [17] K. Wang, H. Si: J. Iron Steel Res. Int., 2014, vol. 21, pp. 1136-1139.10.1016/S1006-706X(14)60195-3 ↗
18. [18] S. H. Song, Y. Zhao, H. Si: Mater. Lett., 2015, vol. 140, pp. 20-22.10.1016/j.matlet.2014.10.158 ↗
19. [19] J. Perháčová, D. Grman, M. Svoboda, J. Patscheider, A. Výrostková, J. Janovec: Mater. Lett., 2001, vol. 47, pp. 44-49.10.1016/S0167-577X(00)00210-X ↗
20. T. Xu: Reference Module in Materials Science and Materials Engineering, Elsevier, 2016, pp. 1-8.
21. [21] Y. Momotani, A. Shibata, D. Terada, N. Tsuji, Int. J. Hydrog. Energy, 2017, Vol. 42, pp. 3371-3379.10.1016/j.ijhydene.2016.09.188 ↗
22. [22] A. Nagao, C.D. Smith, M. Dadfarnia, P. Sofronis, I.M. Robertson, Acta Mater., 2012, Vol. 60, pp. 5182-5189.10.1016/j.actamat.2012.06.040 ↗
23. [23] Q. Liu, Q. Zhou, J. Venezuela, M. Zhang, A. Atrens, Mater. Sci. Eng. A, 2018 Vol. 715, pp. 370-378.10.1016/j.msea.2017.12.079 ↗
24. [24] J. Yang, Y. Song, Y. Lu, J. Gu, Z. Guo, Mater. Sci. Eng. A, 2018, Vol. 712, pp. 630-636.10.1016/j.msea.2017.12.032 ↗
25. SFS-EN ISO 148-1: Mechanical Engineering and Metals Industry Standardization in Finland, 2016.
26. ASTM E1820 - 17a: Standard Test Method for Measurement of Fracture Toughness, 2017.
27. EN 15305: Non-destructive Testing Method for Residual Stress analysis by X-ray Diffraction, 2008.
28. [28] R. Chu, Z. Li, Y. Fan, J. Liu, C. Ma, X. Wang, Heliyon, 2019, Vol. 5, pp. e01329.10.1016/j.heliyon.2019.e01329 ↗
29. [29] C. Wang, M. Wang, J. Shi, W. Hui, H. Dong, Scr. Mater., 2008, Vol. 58, pp. 492-495.10.1016/j.scriptamat.2007.10.053 ↗
30. [30] T. Zhou, H. Yu, S. Wang, Mater. Sci. Eng. A, 2016, Vol. 658, pp. 150-158.10.1016/j.msea.2016.02.001 ↗
31. [31] H. Kim, J. Park, M. Kang, S. Lee, Mater. Sci. Eng. A, 2016, Vol. 649, pp. 57-67.10.1016/j.msea.2015.09.099 ↗
32. [32] S. Li, G. Zhu, Y. Kang, J. Alloys and Compd., 2016, Vol. 675, pp. 104-115.10.1016/j.jallcom.2016.03.100 ↗
33. [33] C. Wang, H. Qiu, Y. Kimura, T. Inoue, Mater. Sci. Eng. A, 2016, Vol. 669, pp. 48-57.10.1016/j.msea.2016.05.041 ↗