Surface Oxidation and Wettability of Fe–Mn and Fe–Mn–Si-Alloyed Steel After Annealing
Source abstract
Abstract
Abstract The surface oxidation and wettability of Mn and Si-alloyed steel after annealing at different conditions are studied with scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and a so-called de-wetting method. After exposure at 950 °C for 1 hour in an Ar + 5 vol pct H2 gas atmosphere with dew points (DP) ranging from – 40 °C to 10 °C, oxides were observed along the grain boundaries or dispersed on the surface for the Fe–1.8 Mn steels while a continuous oxides layer was formed on Fe–1.9 Mn–0.94 Si steels (composition in weight fractions). The oxides formed at different DPs were predicted based on thermodynamic calculations. (Fe,Mn)O was formed on Fe–1.8 Mn steel at the whole range of DPs, while the oxide phase on Fe–1.9 Mn–0.94 Si steel depends on the DP. At low-DP SiO2 were formed and with increasing the DP (Fe,Mn)SiO3 or (Fe,Mn)SiO3 + (Fe,Mn)2SiO4 were formed and finally (Fe,Mn)2SiO4 were formed. An increase of the fraction of Fe in the oxide with increasing DP for both steels was observed with XPS analysis. As a measure for the surface wettability, the contact angle of Pb droplets on the annealed steels surfaces was determined with SEM and image analysis software. Also, the contact angle of Pb on pure Fe and on the Mn and Si alloyed steels free of surface oxides was measured for comparison. The results show that the contact angle of Pb on the steel surfaces after annealing decreases with increasing DP. This improved wettability with increasing dew point is related to the Fe fraction of the oxides formed on the surface.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Corrosion Behavior and Inhibition · Metallurgical Processes and Thermodynamics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. J. Mahieu, S. Claessens, and B.C. De Cooman: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2905–08.10.1007/s11661-001-1042-5 ↗
2. L. Cho, S.J. Lee, M.S. Kim, Y.H. Kim, and B.C. De Cooman: Metall. Mater. Trans. A, 2013, vol. 44, pp. 362–71.10.1007/s11661-012-1392-1 ↗
3. R. Khondker, A. Mertens, and J.R. McDermid: Mater. Sci. Eng. A, 2007, vol. 463, pp. 157–65.10.1016/j.msea.2006.09.116 ↗
4. B. Mintz: Int. Mater. Rev., 2001, vol. 46, pp. 169–97.10.1179/095066001771048754 ↗
5. M. Kim, J. Kwak, J. Kim, Y. Liu, N. Gao, and N.Y. Tang: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 1903–10.10.1007/s11661-009-9880-7 ↗
6. G.M. Song, T. Vystavel, N. van der Pers, J.T.M. De Hosson, and W.G. Sloof: Acta Mater., 2012, vol. 40, pp. 2973–81.10.1016/j.actamat.2012.02.003 ↗
7. A. Marder: Prog. Mater. Sci., 2000, vol. 45, pp. 191–271.10.1016/S0079-6425(98)00006-1 ↗
8. L. Chen, H.S. Kim, S.K. Kim, and B.C. De Cooman: ISIJ Int., 2007, vol. 47, pp. 1804–12.10.2355/isijinternational.47.1804 ↗
9. Q. Tonizzo, A.F. Gourgues-Lorenzon, M. Mazière, A. Perlade, and I. Zuazo: Mater. Sci. Eng. A, 2017, vol. 706, pp. 217–26.10.1016/j.msea.2017.09.002 ↗
10. S. Alibeigi and J.R. McDermid: in Materials Science and Technology Conference and Exhibition 2012, MS and T 2012, 2012, pp. 147–54.
11. E.M. Bellhouse and J.R. McDermid: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 2753–68.10.1007/s11661-011-0685-0 ↗
12. E.M. Bellhouse and J.R. McDermid: Metall. Mater. Trans. A, 2012, vol. 43A, pp. 2426–41.10.1007/s11661-011-0983-6 ↗
13. M.L. Giorgi, J. Diawara, S. Chen, A. Koltsov, and J.M. Mataigne: J. Mater. Sci., 2012, vol. 47, pp. 8483–95.10.1007/s10853-012-6696-4 ↗
14. S. Jiang, S. Feng, X. Yuan, Y. Li, Z. Li, and Q. Zhang: J. Iron. Steel Res. Int., 2014, vol. 21, pp. 1059–64.10.1016/S1006-706X(14)60184-9 ↗
15. Y. Kim, K. Shin, S. Jeon, K. Chin, and J. Lee: Corros. Sci., 2014, vol. 85, pp. 364–71.10.1016/j.corsci.2014.04.034 ↗
16. I. Hertveldt, B.C. De Cooman, and S. Claessens: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1225–32.10.1007/s11661-000-0118-y ↗
17. G.M. Song, W.G. Sloof, T. Vystavel, and J.T.M. De Hosson: Mater. Sci. Forum, 2007, vol. 539–543, pp. 1104–09.10.4028/www.scientific.net/MSF.539-543.1104 ↗
18. A. Mertens, E.M. Bellhouse, and J.R. McDermid: Mater. Sci. Eng. A, 2014, vol. 608, pp. 249–57.10.1016/j.msea.2014.04.074 ↗
19. S. Alibeigi, R. Kavitha, R.J. Meguerian, and J.R. McDermid: Acta Mater., 2011, vol. 59, pp. 3537–49.10.1016/j.actamat.2011.02.027 ↗
20. R. Kavitha and J.R. McDermid: Surf. Coat. Technol., 2012, vol. 212, pp. 152–58.10.1016/j.surfcoat.2012.09.038 ↗
21. M.L. Giorgi and A. Koltsov: in Galvatech 2017, Tokyo, Japan, 2017.
22. M.L. Giorgi, J. Diawara, M. Rivollier, H. Duval, and A. Koltsov: ISIJ Int., 2018, vol. 58, pp. 1592–99.10.2355/isijinternational.ISIJINT-2018-147 ↗
23. M. Pourmajidian and J.R. McDermid: Surf. Coat. Technol., 2019, vol. 357, pp. 418–26.10.1016/j.surfcoat.2018.10.028 ↗
24. V.A. Lashgari, C. Kwakernaak, and W.G. Sloof: Oxid. Met., 2014, vol. 81, pp. 435–51.10.1007/s11085-013-9456-1 ↗
25. W. Mao, R.W. Hendrikx, and W.G. Sloof: Oxid. Met., 2018, vol. 89, pp. 531–49.10.1007/s11085-017-9815-4 ↗
26. W. Mao, Y. Ma, and W.G. Sloof: Oxid. Met., 2018, vol. 90, pp. 237–53.10.1007/s11085-018-9836-7 ↗
27. J. Moon, J. Lowekamp, P. Wynblatt, S. Garoff, and R.M. Suter: Surf. Sci., 2001, vol. 488, pp. 73–82.10.1016/S0039-6028(01)01098-6 ↗
28. Z. Shi and P. Wynblatt: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2569–72.10.1007/s11661-002-0377-x ↗
29. Z. Wang, P. Wynblatt, and D. Chatain: Interface Sci., 1999, vol. 7, pp. 173–80.10.1023/A:1008779501606 ↗
30. D. Huin, P. Flauder, and J.B. Leblond: Oxid. Met., 2005, vol. 64, pp. 131–67.10.1007/s11085-005-5718-x ↗
31. American society for testing and materials. Standard practice for checking the operating characteristics of X-ray photoelectron spectrometers (E902-88). Surf. Interface Anal., 1991, vol. 17, pp. 889–92.10.1002/sia.740171208 ↗
32. T.L. Barr: Modern ESCA: the Principles and Practice of X-Ray Photoelectron Spectroscopy, CRC Press, Boca Raton, 1994.
33. P. Buahom: Measuring the Contact Angle Using ImageJ with Contact Angle Plug-in (ResearchGate, 2018), https://www.researchgate.net/publication/328733959, accessed 05 November 2007.
34. Y.F. Gong and B.C. De Cooman: Steel Res. Int., 2011, vol. 82, pp. 1310–18.10.1002/srin.201100122 ↗
35. Factsage Database Documentation : http://www.crct.polymtl.ca/fact/documentation/, accessed 26 January 2021.
36. P. Franke and R. Dieckmann: J. Phys. Chem. Solids, 1990, vol. 51, pp. 49–57.10.1016/0022-3697(90)90131-X ↗
37. W. Mao and W.G. Sloof: Scr. Mater., 2017, vol. 135, pp. 29–32.10.1016/j.scriptamat.2017.03.009 ↗
38. A.P. Grosvenor, E.M. Bellhouse, A. Korinek, M. Bugnet, and J.R. McDermid: Appl. Surf. Sci., 2016, vol. 379, pp. 242–48.10.1016/j.apsusc.2016.03.235 ↗
39. W.D. Kaplan, D. Chatain, P. Wynblatt, and W.C. Carter: J. Mater. Sci., 2013, vol. 48, pp. 5681–5717.10.1007/s10853-013-7462-y ↗
40. R.J. Good: J. Colloid Interface Sci., 1975, vol. 52, pp. 308–13.10.1016/0021-9797(75)90205-2 ↗
41. I.J. Bennett, J.M. Kranenburg, and W.G. Sloof: J. Am. Ceram. Soc., 2005, vol. 88, pp. 2209–16.10.1111/j.1551-2916.2005.00408.x ↗
42. C. Kwakernaak and W.G. Sloof: Ceram. Int., 2018, vol. 44, pp. 23172–79.10.1016/j.ceramint.2018.09.127 ↗
43. B.J. Keene: Int. Mater. Rev., 1993, vol. 38, pp. 157–92.10.1179/imr.1993.38.4.157 ↗
44. G.M. Song and W.G. Sloof: Surf. Coat. Technol., 2011, vol. 205, pp. 4632–39.10.1016/j.surfcoat.2011.04.014 ↗