Microstructure Evolution and Rapid Solidification Behavior of Blended Nickel-Based Superalloy Powders Fabricated by Laser Powder Deposition
Source abstract
Abstract
Laser powder deposition was performed on a substrate of Inconel 738 using blended powders of Mar M247 and Amdry DF3 with a ratio of 4:1 for repairing purposes. In the as-deposited condition, continuous secondary phases composed of γ-Ni3B eutectics and discrete (Cr, W)B borides were observed in inter-dendritic regions, and time-dependent nucleation simulation results confirmed that (Cr, W)B was the primary secondary phase formed during rapid solidification. Supersaturated solid solution of B was detected in the γ solid solution dendritic cores. The Kurz–Giovanola–Trivedi model was performed to predict the interfacial morphology and correlate the solidification front velocity (SFV) with dendrite tip radius. It was observed from high-resolution scanning electron microscopy that the dendrite tip radius of the upper region was in the range of 15 to 30 nm, which yielded a SFV of approx 30 cm/s. The continuous growth model for solute trapping behavior developed by Aziz and Kaplan was used to determine that the effective partition coefficient of B was approximately 0.025. Finally, the feasibility of the modeling results were rationalized with the Clyne–Kurz segregation simulation of B, where Clyne–Kurz prediction using a partition coefficient of 0.025 was in good agreement with the electron probe microanalysis results.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Solidification and crystal growth phenomena · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. J.N. DuPont, J.C. Lippold and S.D. Kiser: Welding metallurgy and weldability of nickel-base alloys, Wiley, Hoboken, N.J., 2009.10.1002/9780470500262 ↗
2. J.E. Flinkfeldt and T.F. Pedersen: Mater. Sci. Forum, 1994, vol. 163, pp. 423-428.10.4028/www.scientific.net/MSF.163-165.423 ↗
3. M. Riabkina-Fishman and J. Zahavi: Appl. Surf. Sci., 1996, vol. 106, pp. 263-267.10.1016/S0169-4332(96)00408-4 ↗
4. K. Banerjee, N.L. Richards and M.C. Chaturvedi: Metall. Mater. Trans. A, 2005, vol. 36, pp. 1881-1890.10.1007/s11661-005-0051-1 ↗
5. D. Liu, J. Lippold, J. Li, S. Rohklin, J. Vollbrecht and R. Grylls: Metall. Mater. Trans. A, 2014, vol. 45, pp. 4454-4469.10.1007/s11661-014-2397-8 ↗
6. L. Rickenbacher, T. Etter, S. Hövel and K. Wegener: Rapid Prototyping Journal, 2013, vol. 19, pp. 282-290.10.1108/13552541311323281 ↗
7. Y. Nakao: Transactions of the Japan Welding Society, 1988, vol. 19, pp. 66-74.
8. C.Y. Su, C.P. Chou, B.C. Wu and W.C. Lih: J. Mater. Eng. Perform., vol. 6, pp. 619-627.10.1007/s11665-997-0055-7 ↗
9. A.A. Lugan, P.A. Hilton, G.B. Melton and C. Rinaldi: In ICALEO 2006—25th International Congress on Applications of Laser and Electro-Optics, Congress Proceedings, (2006).
10. M.M.M. Ebrahimnia, F. Malek Ghaini and H.R. Shahverdi: Science Technology of Welding Joining, 2014, vol. 19, pp. 25-29.10.1179/1362171813Y.0000000157 ↗
11. B. Alexandrov, A. Hope, J. Sowards, J. Lippold and S. McCracken: Weld World, 2011, vol. 55, pp. 65-76.10.1007/BF03321288 ↗
12. J. Sowards, D. Liang, B. Alexandrov, G. Frankel and J. Lippold: Metall. Mater. Trans. A, 2012, vol. 43, pp. 1209-1222.10.1007/s11661-011-0961-z ↗
13. A.B. Goncharov, J. Liburdi and P. Lowden: Patent Application WO2014085892A1, 2012.
14. A.B. Goncharov, J. Liburdi and P. Lowden: Proceedings of ASME Turbo Expo 2014: Turbine Technical Conference and Exposition, 2014.
15. Y. Tian, D. McAllister, H. Colijn, M. Mills, D. Farson, M. Nordin and S. Babu: Metall. Mater. Trans. A, 2014, vol. 45, pp. 4470-4483.10.1007/s11661-014-2370-6 ↗
16. S. Li, Q. Wei, Y. Shi, Z. Zhu and D. Zhang: J. Mater. Sci. Technol., 2015, vol. 31, pp. 946-952.10.1016/j.jmst.2014.09.020 ↗
17. W.J. Boettinger, L.A. Bendersky, S.R. Coriell, R.J. Schaefer and F.S. Biancaniello: Journal of Crystal Growth, 1987, vol. 80, pp. 17-25.10.1016/0022-0248(87)90518-5 ↗
18. J.C. Baker and J.W. Gahn: Acta Metall., 1969, vol. 17, pp. 575-578.10.1016/0001-6160(69)90116-3 ↗
19. P.M. Smith and M.J. Aziz: Acta Metall. et Mater., 1994, vol. 42, pp. 3515-3525.10.1016/0956-7151(94)90483-9 ↗
20. M.J. Aziz: J. Appl. Phys., 1982, vol. 53, pp. 1158-1168.10.1063/1.329867 ↗
21. M.J. Aziz, J.Y. Tsao, M.O. Thompson, P.S. Peercy and C.W. White: Phys. Rev. Lett., 1986, vol. 56, pp. 2489-2492.10.1103/PhysRevLett.56.2489 ↗
22. P.M. Smith, R. Reitano and M.J. Aziz: In Materials Research Society Symposium Proceedings (1993), pp 749–754.
23. K. Eckler, R.F. Cochrane, D.M. Herlach and B. Feuerbacher: Mater. Sci. Eng., A, 1991, vol. 133, pp. 702-705.10.1016/0921-5093(91)90166-K ↗
24. K. Eckler, D.M. Herlach and M.J. Aziz: Acta Metall. et Mater., 1994, vol. 42, pp. 975-979.10.1016/0956-7151(94)90291-7 ↗
25. M.J. Aziz and T. Kaplan: Acta Metall., 1988, vol. 36, pp. 2335-2347.10.1016/0001-6160(88)90333-1 ↗
26. N.J. Harrison, I. Todd and K. Mumtaz: Acta Mater., 2015, vol. 94, pp. 59-68.10.1016/j.actamat.2015.04.035 ↗
27. R.K. Sidhu, O.A. Ojo and M.C. Chaturvedi: Metall. Mater. Trans. A, 2007, vol. 38, pp. 858-870.10.1007/s11661-006-9063-8 ↗
28. C.A. Schneider, W.S. Rasband and K.W. Eliceiri: Nature Methods, 2012, vol. 9, pp. 671-675.10.1038/nmeth.2089 ↗
29. D. Drouin, A.R. Couture, D. Joly, X. Tastet, V. Aimez and R. Gauvin: Scanning, 2007, vol. 29, pp. 92-101.10.1002/sca.20000 ↗
30. G.P. Dinda, A.K. Dasgupta and J. Mazumder: Mater. Sci. Eng., A, 2009, vol. 509, pp. 98-104.10.1016/j.msea.2009.01.009 ↗
31. F. Xu, Y. Lv, Y. Liu, B. Xu and P. He: Physics Procedia, 2013, vol. 50, pp. 48-54.10.1016/j.phpro.2013.11.010 ↗
32. O.A. Ojo, N.L. Richards and M.C. Chaturvedi: Metall. Mater. Trans. A, 2006, vol. 37, pp. 421-433.10.1007/s11661-006-0013-2 ↗
33. T.B. Massalski, H. Okamoto and A.S.M. International: Binary alloy phase diagrams, ASM International, Materials Park, Ohio, 1990.
34. G. Shao and P. Tsakiropoulos: Acta Metall. et Mater., 1994, vol. 42, pp. 2937-2942.10.1016/0956-7151(94)90391-3 ↗
35. H. Jones: Philosophical Magazine B: Physics of Condensed Matter; Electronic, Optical and Magnetic Properties, 1990, vol. 61, pp. 487-509.10.1080/13642819008219289 ↗
36. V.M. Azhazha, V.E. Semenenko and N.N. Pilipenko: Powder Metall. Met. Ceram., 2007, vol. 46, pp. 32-37.10.1007/s11106-007-0006-8 ↗
37. C.W. Bale, P. Chartrand, S.A. Degterov, G. Eriksson, K. Hack, R. Ben Mahfoud, J. Melançon, A.D. Pelton and S. Petersen: Calphad, 2002, vol. 26, pp. 189-228.10.1016/S0364-5916(02)00035-4 ↗
38. F. Spaepen and D. Turnbull: in Laser Annealing of Semiconductors, J.M.P.W. Mayer, ed., Academic Press, New York, 1982, pp. 15–42.10.1016/B978-0-12-558820-1.50007-7 ↗
39. S. Kou: In Welding Metallurgy, John Wiley & Sons, Inc., New York, pp. 37–64.
40. W. Kurz and D.J. Fisher: Acta Metall., 1981, vol. 29, pp. 11-20.10.1016/0001-6160(81)90082-1 ↗
41. M.H. Burden and J.D. Hunt: J. Cryst. Growth, 1974, vol. 22, pp. 109-116.10.1016/0022-0248(74)90127-4 ↗
42. S.A. David and J.M. Vitek: Int. Mater. Rev., 1989, vol. 34, pp. 213-245.10.1179/imr.1989.34.1.213 ↗
43. W.W. Mullins and R.F. Sekerka: J. Appl. Phys., 1964, vol. 35, pp. 444-451.10.1063/1.1713333 ↗
44. D.E. Hoglund, M.J. Aziz, S.R. Stiffler, M.O. Thompson, J.Y. Tsao and P.S. Peercy: J. Cryst. Growth, 1991, vol. 109, pp. 107–12.10.1016/0022-0248(91)90164-Z ↗
45. W. Kurz, B. Giovanola and R. Trivedi: Acta Metall., 1986, vol. 34, pp. 823-830.10.1016/0001-6160(86)90056-8 ↗
46. W.J. Boettinger and S.R. Coriell: in Science and Technology of the Undercooled Melt, P.R. Sahm, H. Jones and C.M. Adam, eds., Springer, New York, 1986, pp. 81–109.10.1007/978-94-009-4456-5_5 ↗
47. E. Scheil: Z. Metallkd., 1942, vol. 34, pp. 70-72.
48. H.D. Brody and M.C. Flemings: Trans. AIME, 1966, vol. 236, pp. 615-623.
49. T.W. Clyne and W. Kurz: Metall. Trans. A, 1981, vol. 12, pp. 965-971.10.1007/BF02643477 ↗
50. D. Heard: Ph.D. Thesis, McGill University, Montreal, QC, 2013.
51. A. Lal, R.G. Iacocca and R.M. German: Journal of Materials Science, 2000, vol. 35, pp. 4507-4518.10.1023/A:1004893618493 ↗