Effect of Cooling Rate on Microstructure Evolution and Plastic Flow of Ti-6Al-4V
Source abstract
Abstract
The effect of cooling rate following subtransus solution treatment on microstructure evolution and plastic flow of Ti-6Al-4V was established. For this purpose, three types of tests were performed using samples of Ti-6Al-4V with an initial structure of equiaxed α in a matrix of β and a cooling rate of 11, 42, or 180 K/min: (i) Static cooling following solution treatment without or with a prestrain, (ii) constant-strain-rate hot compression during concurrent cooling, and (iii) static cooling to a specified temperature followed by constant-strain-rate isothermal hot compression. The volume fraction of equiaxed α developed during cooling was strongly dependent on cooling rate, but pre- or concurrent deformation resulted in relatively-small changes in this quantity. In addition, the cooling rate through its effect on the growth kinetics of equiaxed α had a noticeable effect on plastic-flow behavior under both isothermal and non-isothermal conditions. In both instances, the retention of the high-temperature microstructure (characterized by a low fraction of equiaxed α) during rapid cooling gave rise to lower flow stresses than samples with equilibrium equiaxed phase fractions. By contrast, when secondary α was formed during cooling, higher flow stresses were generated due to a Hall-Petch-like effect. The results were interpreted using models for the diffusional growth of equiaxed α, the onset of nucleation of secondary α, and predictions of the plastic-flow response of equiaxed two-phase microstructures based on a self-consistent approach. Unlike previous findings which indicated a large increase in the rate of dissolution of equiaxed α due to concurrent deformation/pipe diffusion during heating transients, the present work did not reveal a corresponding enhancement of growth during cooling.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Metal and Thin Film Mechanics · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (52)
Show source-provided references
1. S.L. Semiatin and G.D. Lahoti: Metall. Trans. A, 1981, vol. 12A, pp. 1705-1717.10.1007/BF02643753 ↗
2. T. Seshacharyulu, S.C. Madeiros, W.G. Frazier, and Y.V.R.K. Prasad: Mater. Sci. Eng. A, 2000, vol. A284, pp. 184-194.10.1016/S0921-5093(00)00741-3 ↗
3. J. Cao, F. Li, T. Liu, B. Chen, and M. He: Mater. Design, 2011, vol. 32, pp. 1144-1151.10.1016/j.matdes.2010.11.004 ↗
4. J.S. Jha, S.P. Toppo, R. Singh, A. Tewari, and S.K. Mishra: J. Mater. Proc. Technol., 2019, vol. 270, pp. 216-227.10.1016/j.jmatprotec.2019.02.030 ↗
5. C.M. Young and O.D. Sherby: in Metal Forming-Interrelation between Theory and Practice, A.L. Hoffmanner, ed., Plenum Press, New York, 1971, pp. 429–51.10.1007/978-1-4615-1757-3_19 ↗
6. S. Fulop, K.C. Cadien, M.J. Luton, and M.J. McQueen: J. Testing Eval., 1977, vol. 5, pp. 419-426.10.1520/JTE10554J ↗
7. J.P.A. Immarigeon and P.H. Floyd: Metall. Trans. A, 1981, vol. 12A, pp. 1177- 1186.10.1007/BF02642331 ↗
8. A.A. Guimaraes and J.J. Jonas: Metall. Trans., 1981, vol. 12A, pp. 1655-1666.10.1007/BF02643571 ↗
9. A.K. Koul and J-P.A. Immarigeon: Acta Metall., 1987, vol. 35, pp. 1791-1805.10.1016/0001-6160(87)90125-8 ↗
10. S.L. Semiatin, K.E. McClary, A.D. Rollett, C.G. Roberts, E.J. Payton, F. Zhang, and T.P. Gabb: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 2778-2798.10.1007/s11661-013-1675-1 ↗
11. P.D. Nicolaou, R.E. Bailey, and S.L. Semiatin: in Handbook of Workability and Process Design, G.E. Dieter, H.A. Kuhn, and S.L. Semiatin, eds., ASM International, Materials Park, OH, 2003, pp. 68–85.
12. H.G. Suzuki and H. Fujii: ISIJ Inter., 1991, vol. 31, pp. 814-819.10.2355/isijinternational.31.814 ↗
13. H.G. Suzuki and D. Eylon: ISIJ Inter., 1993, vol. 33, pp. 1270-1274.10.2355/isijinternational.33.1270 ↗
14. H.G. Suzuki and D. Eylon: Mater. Sci. Eng. A, 1998, vol. A243, pp. 126-133.10.1016/S0921-5093(97)00789-2 ↗
15. F.F. Noecker II and J.N. DuPont: Weld. J., 2009, vol. 88 (#1), pp. 7s–20s.
16. S. Shi, J.C. Lippold, and J. Ramirez: Weld. J. 2010, vol. 89 (#10), pp. 210s–217s.
17. S.S. Babu, J. Livingston, and J.C. Lippold: Metall. Mater. Trans. A, 2013, vol. 44, pp. 3577-3591.10.1007/s11661-013-1782-z ↗
18. M. Saby, E. Massoni, and N. Bozzolo: Mater. Charact., 2014, vol. 89, pp. 88–92.10.1016/j.matchar.2014.01.001 ↗
19. S.L. Semiatin, N.C. Levkulich, C.A. Heck, A.E. Mann, N. Bozzolo, A.L. Pilchak, and J.S. Tiley: Metall. Mater. Trans. A, 2020, vol. 51A, pp. 2291-2305.10.1007/s11661-020-05673-9 ↗
20. S.L. Semiatin, F. Montheillet, G. Shen, and J.J. Jonas: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2719-2727.10.1007/s11661-002-0394-9 ↗
21. G. Shen, S.L. Semiatin, E. Kropp, and T. Altan: J. Mater. Proc. Technol., 1992, vol. 33, pp. 125–39.10.1016/0924-0136(92)90315-J ↗
22. S.L. Semiatin, M. Obstalecki, E.J. Payton, A.L. Pilchak, P.A. Shade, N.C. Levkulich, J.M. Shank, D.C. Pagan, F. Zhang, and J.S. Tiley: Metall. Mater. Trans. A, 2019, vol.50A, pp. 2356-2370.10.1007/s11661-019-05164-6 ↗
23. S.L. Semiatin, S.L. Knisley, P.N. Fagin, F. Zhang, and D.R. Barker: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2377-2386.10.1007/s11661-003-0300-0 ↗
24. S.I. Oh, S.L. Semiatin, and J.J. Jonas: Metall. Trans. A, 1992, vol. 23A, pp. 963-975.10.1007/BF02675571 ↗
25. X. Gao, W. Zeng, S. Zhang, and Q. Wang: Acta Mater., 2017, vol. 122, pp. 298-309.10.1016/j.actamat.2016.10.012 ↗
26. M. Meng, H. Yang, X.G. Fan, S.L. Yan, A.M. Zhao, and S. Zhu: J. Alloys Comp., 2017, vol. 691, pp. 67-80.10.1016/j.jallcom.2016.08.218 ↗
27. M. Meng, X.G. Fan, H. Yang, L.G. Guo, M. Zhan, and P.F. Gao: J. Alloys Comp., 2017, vol. 714, pp. 294-302.10.1016/j.jallcom.2017.04.209 ↗
28. R.H. Buzolin, D. Weiss, A. Krumphals, M. Lasnik, and M.C. Poletti: Metall. Mater. Trans. A, 2020, vol. 51A, pp. 3967-3980.10.1007/s11661-020-05810-4 ↗
29. W.W. Mullins and R.F. Sekerka: J. Appl. Physics, 1963, vol. 34, pp. 323-329.10.1063/1.1702607 ↗
30. S.L. Semiatin and T.R. Bieler, Acta Mater., 2001, vol. 49, pp. 3565-3573.10.1016/S1359-6454(01)00236-1 ↗
31. C. Zener: J. Appl Phys., 1949, vol. 20, pp. 950-953.10.1063/1.1698258 ↗
32. H.S. Carslaw and J.C. Jaeger: Conduction of Heat in Solids, Oxford University Press, London, 1959.
33. H.B. Aaron, D. Fainstein, and G.R. Kotler: J. Appl. Physics, 1970, vol. 41, pp. 4404-4410.10.1063/1.1658474 ↗
34. O. Grong and H.R. Shercliff: Progress in Materials Science, 2002, vol. 47, pp. 163-282.10.1016/S0079-6425(00)00004-9 ↗
35. U. Zwicker: Titanium and Titanium Alloys, Springer Verlag, Berlin, 1974.
36. H. Wang, N. Warnken, and R.C. Reed: Mater. Sci. Eng. A, 2010, vol. A528, pp. 622-630.10.1016/j.msea.2010.09.013 ↗
37. A.J. Ardell and M.A. Przystupa: High Temp. Mater. Proc., 1993, vol. 12 (#1-2), pp. 1–11.10.1515/HTMP.1993.12.1-2.1 ↗
38. N. Ma, F. Yang, C. Shen, G. Wang, G.B. Viswanathan, P.C. Collins, D. Xu, H.L. Fraser, and Y. Wang: in Ti-2007 Science and Technology, M. Ninomi, S. Akiyama, M. Ikeda, M. Hagiwara, and K. Maruyama, eds., Japan Institute of Metals, Sendai, Japan, 2007, pp. 287–90.
39. I. Katzarov, S. Malinov, and W. Sha: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 1027-1040.10.1007/s11661-002-0204-4 ↗
40. R.D. Doherty: in Physical Metallurgy, R.W. Cahn and P. Haasen, eds., North-Holland, Amsterdam, 1996, ch. 15.
41. H.I. Aaronson and F.K. LeGoues: Metall. Trans. A, 1992, vol. 23, pp. 1915-1945.10.1007/BF02647541 ↗
42. S.Q. Xiao and P. Haasen: Acta Metall. et Mater., 1991, vol. 39, pp. 651-659.10.1016/0956-7151(91)90133-L ↗
43. K.S. Chan, J.K. Lee, G.J. Shiflet, K.C. Russell, and H.I. Aaronson: Metall. Trans. A, 1978, vol. 9A, pp. 1016-1017.10.1007/BF02649849 ↗
44. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, Elsevier Science Ltd., Oxford, UK, 1996.
45. F.R.N. Nabarro: Proc. R. Soc. Lond. Ser. A, Math. Phys. Sci., 1940, vol. 175 (#963), pp. 519–38.10.1098/rspa.1940.0072 ↗
46. M. Humbert, L. Germaine, N. Gey, P. Bocher, and M. Jahazi: Mater. Sci. Eng. A, 2006, vol. A430, pp. 157-164.10.1016/j.msea.2006.05.047 ↗
47. R. Pederson, O.Babushkin, F. Skystedt, and R. Warren: Mater. Sci. Techn., 2003, vol. 19, pp. 1533-1538.10.1179/026708303225008013 ↗
48. S.L. Semiatin, S.L. Kim, F. Zhang, and J.S. Tiley: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 1715-1730.10.1007/s11661-015-2748-0 ↗
49. S.L. Semiatin, F. Zhang, R. Larsen, L.A. Chapman, and D.U. Furrer: Integrating Materials and Manufacturing Innovation, 2016, vol. 5, no. 3, pp. 1-20.
50. S.L. Semiatin, T.M. Brown, T.A. Goff, P.N. Fagin, D.R. Barker, R.E. Turner, J.M. Murry, J.D. Miller, and F. Zhang: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 3015-3018.10.1007/s11661-004-0250-1 ↗
51. S. Zherebtsov, G.A. Salishchev, and S.L. Semiatin: Phil. Mag. Lett., 2010, vol. 90 (#12), pp. 903–14.10.1080/09500839.2010.521526 ↗
52. L. Briottet, J.J. Jonas, and F. Montheillet: Acta Mater., 1996, vol. 44, pp. 1665-1672.10.1016/1359-6454(95)00257-X ↗