journal article·2017-08Open access

Effect of Microstructure on Electrical Conductivity of Nickel-Base Superalloys

Balasubramanian Nagarajan, Sylvie Castagne, Swaminathan Annamalai, Zheng Fan, Wai Luen Chan

Abstract

Eddy current spectroscopy is one of the promising non-destructive methods for residual stress evaluation along the depth of subsurface-treated nickel-base superalloys, but it is limited by its sensitivity to microstructure. This paper studies the influence of microstructure on the electrical conductivity of two nickel-base alloys, RR1000 and IN100. Different microstructures were attained using heat treatment cycles ranging from solution annealing to aging, with varying aging time and temperature. Eddy current conductivity was measured using conductivity probes of frequencies ranging between 1 and 5 MHz. Qualitative and quantitative characterization of the microstructure was performed using optical and scanning electron microscopes. For the heat treatment conditions between the solution annealing and the peak aging, the electrical conductivity of RR1000 increased by 6.5 pct, which is duly substantiated by the corresponding increase in hardness (12 pct) and the volume fraction of γ′ precipitates (41 pct). A similar conductivity rise of 2.6 pct for IN100 is in agreement with the increased volume fraction of γ′ precipitates (12.5 pct) despite an insignificant hardening between the heat treatment conditions. The observed results with RR1000 and IN100 highlight the sensitivity of electrical conductivity to the minor microstructure variations, especially the volume fraction of γ′ precipitates, within the materials.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Non-Destructive Testing Techniques · Welding Techniques and Residual Stresses · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Igor Altenberger, Alternative Mechanical Surface Treatments: Microstructures, Residual Stresses & Fatigue Behavior, in Shot Peening, Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim, FRG, 2006, pp. 419-34.
2. C. O. Ruud, NDT International, 1982, vol. 15, pp. 15-23.10.1016/0308-9126(82)90083-9 ↗
3. PJ Withers and HKDH Bhadeshia, Mater. Sci. Technol. 2001, vol. 17, pp. 355–65.10.1179/026708301101509980 ↗
4. H. Chang, F.C. Schoenig and Jack A. Soules, In Conf Proc: ICSP-6, 1996, pp. 356–84.
5. Mark P. Blodgett and Peter B. Nagy, J Nondestruct Eval 2004, vol. 23, pp. 107–23.10.1023/B:JONE.0000048866.40648.fe ↗
6. Feng Yu and Peter B. Nagy, J. Appl. Phys. 2004, vol. 96, pp. 1257–66.10.1063/1.1762708 ↗
7. Bassam A. Abu-Nabah and Peter B. Nagy, NDT E Int., 2006, vol. 39, pp. 641–51.10.1016/j.ndteint.2006.05.001 ↗
8. Y. Shen, C. Lee, C. C. H. Lo, N. Nakagawa and A. M. Frishman, J. Appl. Phys., 2007, vol. 101, pp. 014907.10.1063/1.2403970 ↗
9. Yuichi Sekine and Hitoshi Soyama, Surf. Coat. Technol., 2009, vol. 203, pp. 2254–59.10.1016/j.surfcoat.2009.02.018 ↗
10. Bassam A. Abu-Nabah, Feng Yu, Waled T. Hassan, Mark P. Blodgett and Peter B. Nagy, Nondestruct. Test. Eval., 2009, vol. 24, pp. 209–32.10.1080/10589750802245280 ↗
11. Feng Yu and Peter B. Nagy, J Nondestruct Eval., 2006, vol. 25, pp. 107–22.10.1007/s10921-006-0009-2 ↗
12. R. Chandrasekar, A. M. Frishman, B. F. Larson, C. C. H. Lo and N. Nakagawa, JOM, 2012, vol. 64, pp. 257–64.10.1007/s11837-012-0234-3 ↗
13. S. Hillmann, H. Heuer and N. Meyendorf, In SPIE Smart Structures and Materials+ Nondestructive Evaluation and Health Monitoring, International Society for Optics and Photonics, 2009, pp. 72930S-72930S-9.10.1117/12.815455 ↗
14. T.A. Parthasarathy, S. Boone, S.I. Rao, P. Wang, P.B. Nagy and M.P. Blodgett, Electromagnetic Nondestructive Evaluation (XIII), IOS Press BV, Netherlands, 2010, vol. 13, pp. 165.
15. M. Zergoug, S. Lebaili, H. Boudjellal and A. Benchaala, NDT E Int., 2004, vol. 37, pp. 65-72.10.1016/j.ndteint.2003.09.002 ↗
16. S Hillmann, H Heuer, HU Baron, J Bamberg, A Yashan and N Meyendorf, Proc. Rev. Prog. QNDE 2008, vol. 28, p. 1349.
17. B.A. Abu-Nabah, W.T. Hassan, D. Ryan, M.P. Blodgett and P.B. Nagy, J. Nondestruct. Eval., 2010, vol. 29, pp. 143–53.10.1007/s10921-010-0072-6 ↗
18. R. Chandrasekar, C. C. H. Lo, A. M. Frishman, B. F. Larson and N. Nakagawa, AIP Conf. Proc., 2012, vol. 1430, pp. 1437–44.10.1063/1.4716385 ↗
19. D Pereira, T Clarke, R Menezes and T Hirsch, Mater. Sci. Technol.,2015, vol. 31, pp. 669–76.10.1179/1743284714Y.0000000638 ↗
20. R. J. White, S. B. Fisher, K. M. Miller and G. A. Swallow, Journal of Nuclear Materials 1974, vol. 52, pp. 51–58.10.1016/0022-3115(74)90024-5 ↗
21. V. Siva Kumar G. Kelekanjeri, Lewis K. Moss, Rosario A. Gerhardt and Jan Ilavsky, Acta Materialia, 2009, vol. 57, pp. 4658–70.10.1016/j.actamat.2009.06.019 ↗
22. Ricky L. Whelchel, V. Siva Kumar G. Kelekanjeri, Rosario A. Gerhardt, International Heat Treatment and Surface Engineering, 2009, vol. 3, pp. 35-39.10.1179/174951409X12450558152589 ↗
23. Ricky L. Whelchel, V. Siva Kumar G. Kelekanjeri, Rosario A. Gerhardt and Jan Ilavsky, Metall. Mater. Trans. A, 2010, vol. 42, pp. 1362–72.
24. D. M. Knowles and D. W. Hunt, Metall. Mater. Trans. A, 2002, vol. 33, pp. 3165–72.10.1007/s11661-002-0302-3 ↗
25. HT Pang, MC Hardy, N Hide, IM Wilcock, MB Henderson and PAS Reed, Mater. Sci. Technol., 2015, doi:10.1179/1743284715Y.0000000060.10.1179/1743284715Y.0000000060 ↗
26. S. Birosca, F. Di Gioacchino, S. Stekovic and M. Hardy, Acta Mater., 2014, vol. 74, pp. 110–24.10.1016/j.actamat.2014.04.039 ↗
27. ASTM-International: ASTM E1245 - Standard Practice for Determining the Inclusion or Second-Phase Constituent Content of Metals by Automatic Image Analysis, 2003.
28. ASTM-International: ASTM E112 - Standard Test Methods for Determining Average Grain Size, 2010.
29. G. P. Sabol and R. Stickler, Phys. Status Solidi B, 1969, vol. 35, pp. 11-52.10.1002/pssb.19690350102 ↗
30. H. Chandler: Heat treater’s guide: Practices and Procedures for Nonferrous alloys. ASM international, Materials Park, OH, 1996.
31. M.J. Donachie and S.J. Donachie, Superalloys - A Technical Guide, 2nd ed., ASM International,Materials Park, OH, 2002.10.31399/asm.tb.stg2.9781627082679 ↗
32. T. Özel and Y. M. Arisoy, Procedia CIRP, 2014, vol. 13, pp. 302–07.10.1016/j.procir.2014.04.051 ↗