journal article·2021-05Open access

The Influence of Induction Sintering on Microstructure and Deformation Behavior of Ti-5Al-5Mo-5V-3Cr Alloy

Krystian Zyguła, Marek Wojtaszek, Tomasz Śleboda, Sebastian Lech, Oleksandr Lypchanskyi, Grzegorz Korpała, Ulrich Prahl

Abstract

Abstract The influence of the induction sintering process at different temperatures on the behavior of the powder metallurgy Ti-5Al-5Mo-5V-3Cr alloy was investigated. Material for the research was produced by elemental powder blending, followed by the uniaxial cold compacting process. Powder compacts were induction heated and sintered within the temperature range of 1000 °C to 1300 °C. The influences of process parameters on the material behavior during sintering and its properties were studied. The microstructure examination was performed with particular attention to the pore size and distribution as well as the homogenization of the microstructure. The sintering temperature of 1200 °C proved to be critical for the dissolution of most alloying powder particles. Hot compression tests were performed to determine the formability of the obtained material. Significant differences in flow stress behavior between samples sintered at temperatures below and above 1200 °C were observed. The mechanical properties of the material before and after deformation were compared. The evolution of the microstructure of sintered Ti-5Al-5Mo-5V-3Cr alloy after hot deformation was analyzed with an emphasis on its influence on the material properties. Based on the conducted research, it was found that the adequate homogenization of the chemical composition and microstructure was achieved at the temperature of 1250 °C, and a further increase did not reflect in a significant improvement.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced materials and composites · Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. R.A. Antunes, C.A.F. Salvador, and M.C.L. de Oliveira: Mater. Res. doi:10.1590/1980-5373-mr-2017-0979, 201810.1590/1980-5373-mr-2017-0979 ↗
2. F.H. Froes, H. Friedrich, J. Kiese, and D. Bergoint: JOM, 2004, vol. 56, pp. 40–4.10.1007/s11837-004-0144-0 ↗
3. L.C. Campanelli, P.S.C.P. da Silva, and C. Bolfarini: Mater. Sci. Eng. A, 2016, vol. 658, pp. 203–9.10.1016/j.msea.2016.02.004 ↗
4. N.S. Weston and M. Jackson: J. Mater. Process. Technol., 2017, vol. 243, pp. 335–46.10.1016/j.jmatprotec.2016.12.013 ↗
5. A. Carman, L.C. Zhang, O.M. Ivasishin, D.G. Savvakin, M. V. Matviychuk, and E. V. Pereloma: Mater. Sci. Eng. A, 2011, vol. 528, pp. 1686–93.10.1016/j.msea.2010.11.004 ↗
6. Y.F. Yang, S.D. Luo, G.B. Schaffer, and M. Qian: Mater. Sci. Eng. A, 2011, vol. 528, pp. 6719–26.10.1016/j.msea.2011.05.041 ↗
7. R. Naseri, D.R.G. Mitchell, D.G. Savvakin, M.J.B. Nancarrow, T. Furuhara, A.A. Saleh, A.A. Gazder, and E. V. Pereloma: Mater. Sci. Eng. A, 2019, vol. 747, pp. 232–43.10.1016/j.msea.2018.12.094 ↗
8. S. Grasso, Y. Sakka, and G. Maizza: Sci. Technol. Adv. Mater., 2009, vol. 10, p. 053001.10.1088/1468-6996/10/5/053001 ↗
9. O. Guillon, J. Gonzalez-Julian, B. Dargatz, T. Kessel, G. Schierning, J. Räthel, and M. Herrmann: Adv. Eng. Mater., 2014, vol. 16, pp. 830–49.10.1002/adem.201300409 ↗
10. J.L. Xu, S.C. Tao, L.Z. Bao, J.M. Luo, and Y.F. Zheng: Mater. Sci. Eng. C, 2019, vol. 97, pp. 156–65.10.1016/j.msec.2018.12.028 ↗
11. M.T. Jia, B. Gabbitas, and L. Bolzoni: J. Mater. Process. Technol., 2018, vol. 255, pp. 611–20.10.1016/j.jmatprotec.2018.01.013 ↗
12. F. Raether and P. SchulzeHorn: J. Eur. Ceram. Soc., 2009, vol. 29, pp. 2225–34.10.1016/j.jeurceramsoc.2009.01.025 ↗
13. R. Grupp, M. Nöthe, B. Kieback, and J. Banhart: Nat. Commun., 2011, vol. 2, p. 298.10.1038/ncomms1300 ↗
14. S.J. Kang: Sintering, Elsevier, Amsterdam, 2005.
15. S.S. Dheda and F.A. Mohamed: Mater. Sci. Eng. A, 2011, vol. 528, pp. 8179–86.10.1016/j.msea.2011.07.032 ↗
16. O. Lypchanskyi, T. Śleboda, M. Wojtaszek, K. Muszka, A. Łukaszek-Sołek, R. Stanik, and M. Gude: Int. J. Mater. Form., 2019. https://doi.org/10.1007/s12289-019-01533-z.10.1007/s12289-019-01533-z ↗
17. M. Wojtaszek, G. Korpała, T. Śleboda, K. Zyguła, and U. Prahl: Metall. Mater. Trans. A, 2020, vol. 51, pp. 5790–805.10.1007/s11661-020-05942-7 ↗
18. Y.C. Wang and T.G. Langdon: J. Mater. Sci., 2013, vol. 48, pp. 4646–52.10.1007/s10853-012-7071-1 ↗
19. L. Bolzoni, S. Raynova, and F. Yang: J. Alloys Compd., 2020, vol. 838, p. 155559.10.1016/j.jallcom.2020.155559 ↗
20. B. Callegari, J.P. Oliveira, R.S. Coelho, P.P. Brito, N. Schell, F.A. Soldera, F. Mücklich, M.I. Sadik, J.L. García, and H.C. Pinto: Mater. Charact., 2020, vol. 162, p. 110180.10.1016/j.matchar.2020.110180 ↗
21. K. Zyguła, M. Wojtaszek, O. Lypchanskyi, T. Śleboda, G. Korpała, and U. Prahl: Metall. Mater. Trans. A., 2019, vol. 50, pp. 5314–23.10.1007/s11661-019-05434-3 ↗
22. Q. Zhao, F. Yang, R. Torrens, and L. Bolzoni: Mater. Des., 2019, vol. 169, p. 107682.10.1016/j.matdes.2019.107682 ↗
23. L. Kang and C. Yang: Adv. Eng. Mater., 2019, vol. 21, p. 1801359.10.1002/adem.201801359 ↗
24. J.G. Kaufman: Titanium Alloy Database - Knovel, http://app-1knovel-1com-1000014rj00eb.wbg2.bg.agh.edu.pl/web/toc.v/cid:kpTAD00001/viewerType:toc//root_slug:titanium-alloy-database/url_slug:table-9b-typical-physical?b-q=material_or_substance_name%3Ati-5553&b-group-by=true&b-dsQuery=%3Fmn%3Dti-5553&b-. Accessed 8 December 2020.
25. M. Jia and B. Gabbitas: Metall. Mater. Trans. A , 2015, vol. 46A, pp. 4716–29.10.1007/s11661-015-3048-4 ↗
26. P. Sun, Z.Z. Fang, Y. Zhang, and Y. Xia: Jom, 2017, vol. 69, pp. 1853–60.10.1007/s11837-017-2513-5 ↗
27. J. Zhang, D. Gu, Y. Yang, H. Zhang, H. Chen, D. Dai, and K. Lin: Engineering, 2019, vol. 5, 2850-57.
28. S. Patra, A Gouthama, and K. Mondal: Prog. Nat. Sci. Mater. Int., 2014, vol. 24, pp. 608–22.10.1016/j.pnsc.2014.10.006 ↗
29. Y.W. Marsumi and A.W. Pramono: Adv. Mater. Res., 2014, vol. 900, pp. 53–63.10.4028/www.scientific.net/AMR.900.53 ↗
30. I.M. Robertson and G.B. Schaffer: Metall. Mater. Trans. A, 2009, vol. 40, pp. 1968–79.10.1007/s11661-009-9894-1 ↗
31. D.Y. Park, S.W. Lee, S.J. Park, Y.-S. Kwon, and I. Otsuka: Metall. Mater. Trans. A, 2013, vol. 44, pp. 1508–18.10.1007/s11661-012-1477-x ↗
32. J.W. Oh, Y. Seong, D.S. Shin, and S.J. Park: Powder Technol., 2019, vol. 352, pp. 42–52.10.1016/j.powtec.2019.04.056 ↗
33. K. Zyguła and M. Wojtaszek: Arch. Metall. Mater., 2020, vol. 65, pp. 287–93.
34. S. Raynova, Y. Collas, F. Yang, and L. Bolzoni: Metall. Mater. Trans. A, 2019, vol. 50A, pp. 4732–42.10.1007/s11661-019-05381-z ↗
35. B.B. Panigrahi and M.M. Godkhindi: Intermetallics, 2006, vol. 14, pp. 130–5.10.1016/j.intermet.2005.04.020 ↗
36. B.B. Panigrahi: Mater. Lett., 2007, vol. 61, pp. 152–5.10.1016/j.matlet.2006.04.025 ↗
37. B.B. Panigrahi, M.M. Godkhindi, K. Das, P.G. Mukunda, and P. Ramakrishnan: Mater. Sci. Eng. A, 2005, vol. 396, pp. 255–62.10.1016/j.msea.2005.01.016 ↗
38. Y. Liu, L.F. Chen, H.P. Tang, C.T. Liu, B. Liu, and B.Y. Huang: Mater. Sci. Eng. A, 2006, vol. 418, pp. 25–35.10.1016/j.msea.2005.10.057 ↗
39. O.M. Ivasishin and D.G. Savvakin: Key Eng. Mater., 2010, vol. 436, pp. 113–21.10.4028/www.scientific.net/KEM.436.113 ↗
40. W. Hermel, G. Leitner, and R. Krumphold: Powder Metall., 1980, vol. 23, pp. 130–5.10.1179/pom.1980.23.3.130 ↗
41. S. Raynova, F. Yang, and L. Bolzoni: Mater. Sci. Eng. A, 2021, vol. 799, p. 140157.10.1016/j.msea.2020.140157 ↗
42. S.-Y. Lee, Y. Iijima, and K. Hirano: Mater. Trans. JIM, 1991, vol. 32, pp. 451–6.10.2320/matertrans1989.32.451 ↗
43. S.-Y. Lee, O. Taguchi, and Y. Iijima: Mater. Trans., 2010, vol. 51, pp. 1809–13.10.2320/matertrans.M2010225 ↗
44. I. Philippart and H.J. Rack: Mater. Sci. Eng. A, 1998, vol. 243, pp. 196–200.10.1016/S0921-5093(97)00800-9 ↗
45. W. Chuan and H. Liang: Vacuum, 2018, vol. 156, pp. 384–401.10.1016/j.vacuum.2018.07.056 ↗
46. X. Wang, L. Wang, L.S. Luo, H. Yan, X.Z. Li, R.R. Chen, Y.Q. Su, J.J. Guo, and H.Z. Fu: Mater. Des., 2017, vol. 121, pp. 335–44.10.1016/j.matdes.2017.02.075 ↗
47. S.L. Semiatin and T.R. Bieler: Acta mater, 2001, vol. 49, pp. 3565–73.10.1016/S1359-6454(01)00236-1 ↗
48. Y.V.R.K. Prasad and T. Seshacharyulu: Mater. Sci. Eng. A, 1998, vol. 243, pp. 82–8.10.1016/S0921-5093(97)00782-X ↗
49. R. Narayanasamy and K.S. Pandey: J. Mater. Process. Technol., 2000, vol. 100, pp. 87–94.10.1016/S0924-0136(99)00457-4 ↗
50. S.L. Semiatin: Metall. Mater. Trans. A, 2020, vol. 51, pp. 2593–625.10.1007/s11661-020-05625-3 ↗
51. E. Calvert, B. Wynne, N. Weston, A. Tudball, and M. Jackson: J. Mater. Process. Technol., 2018, vol. 254, pp. 158–70.10.1016/j.jmatprotec.2017.11.035 ↗
52. S.L. Semiatin, V. Seetharaman, and I. Weiss: Mater. Sci. Eng. A, 1999, vol. 263, pp. 257–71.10.1016/S0921-5093(98)01156-3 ↗
53. M. Sen, S. Suman, T. Banerjee, A. Bhattacharjee, and S.K. Kar: Mater. Sci. Eng. A, 2019, vol. 753, pp. 156–67.10.1016/j.msea.2019.03.003 ↗
54. Y.C. Lin, L.-H. Wang, Q. Wu, Y.-W. Xiao, H. Cheng, and X.-Y. Zhang: Mater. Res. Express, 2019, vol. 6, p. 1165h2.10.1088/2053-1591/ab5252 ↗
55. M. Ahmed, D.G. Savvakin, O.M. Ivasishin, and E. V. Pereloma: J. Alloys Compd., 2017, vol. 714, pp. 610–8.10.1016/j.jallcom.2017.04.266 ↗
56. F. Yang, B. Gabbitas, M. Dore, A. Ogereau, S. Raynova, and L. Bolzoni: Mater. Chem. Phys., 2018, vol. 211, pp. 406–13.10.1016/j.matchemphys.2018.03.007 ↗