The Interface Zone of Explosively Welded Titanium/Steel after Short-Term Heat Treatment
Source abstract
Abstract
Abstract This work presents a detailed description of a bonding zone of explosively welded Ti/steel clads subjected to stress relief annealing, applied in order to improve the plasticity of the final product. The typical joint formed by the welding process possesses a characteristic wavy interface with melted regions observed mainly at the crest regions of waves. The interface of Ti/steel clads before and after annealing was previously investigated mostly in respect to the melted regions. Here, a sharp interface between the waves was analyzed in detail. The obtained results indicate that the microstructure of a transition zone of that area is different along the width. After the heat treatment at 600 °C for 1.5 hours, titanium carbide (TiC) together with α-Fe phase forms at the interface in local areas of relatively wide interlayer (~ 1 µm), while for most of the sharp interface, a much thinner zone up to about 400 nm, formed by four sublayers containing intermetallic phase and carbides, is present. This confirms that carbon diffusion induced by applied heat treatment significantly influences the final microstructure of the Ti/steel interface zone. Side bending tests confirmed high plasticity of welds after applied heat treatment; however, the microhardness measurements indicated that the strengthening of the steel in the vicinity of the interface had not been removed completely.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (15)
Show source-provided references
1. N. Kahraman, B. Gülenç, and F. Findik: J. Mater. Process. Technol., 2005, vol. 169, pp. 127–33.10.1016/j.jmatprotec.2005.06.045 ↗
2. Q. Chu, M. Zhang, J. Li, and C. Yan: Mater. Sci. Eng. A, 2017, vol. 689, pp. 323–31.10.1016/j.msea.2017.02.075 ↗
3. P. Manikandan, K. Hokamoto, A.A. Deribas, K. Raghukandan, and R. Tomoshige: Mater. Trans., 2006, vol. 47, pp. 2049–55.10.2320/matertrans.47.2049 ↗
4. M. Wachowski, M. Gloc, T. Ślęzak, T. Płociński, and K.J. Kurzydłowski: J. Mater. Eng. Perform., 2017, vol. 26, pp. 945–54.10.1007/s11665-017-2520-2 ↗
5. H. Jiang, X. Yan, J. Liu, and X. Duan: Trans. Nonferrous Met. Soc. China, 2014, vol. 24, pp. 697–704.10.1016/S1003-6326(14)63113-7 ↗
6. Z. Guoyin, S. Xi, and Z. Jinghua: Rare Met. Mater. Eng., 2017, vol. 46 (4), pp. 906–11.10.1016/S1875-5372(17)30120-0 ↗
7. J. Song, A. Kostka, M. Veehmayer, and D. Raabe: Mater. Sci. Eng. A, 2011, vol. 528, pp. 2641–47.10.1016/j.msea.2010.11.092 ↗
8. T.N. Prasanthi, C. Sudha, Ravikirana, and S. Saroja (2016) Mater. Des., 93, 180–93.10.1016/j.matdes.2015.12.120 ↗
9. A. Karolczuk, H. Paul, Z. Szulc, K. Kluger, M. Najwer, and G. Kwiatkowski: J. Mater. Eng. Perform., 2018, vol. 27, pp. 4571–81.10.1007/s11665-018-3559-4 ↗
10. Yibin Xu, Masayoshi Yamazaki, and Pierre Villars (2011) Jpn. J. Appl. Phys., 50, 11.
11. J. Haitao, Y. Xiaoqian, L. Jixiong, D. Xiaoge, and Z. Shangwu: Rare Met. Mater. Eng., 2014, vol. 43 (11), pp. 2631–36.10.1016/S1875-5372(15)60016-9 ↗
12. T.N. Prasanthi, C. Sudha, P.K. Parida, A. Dasgupta, and S. Saroja: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 1519–34.10.1007/s11661-015-2768-9 ↗
13. M. Gloc, M. Wachowski, T. Plocinski, and K.J. Kurzydlowski: J. Alloys Compd., 2016, vol. 671, pp. 446–51.10.1016/j.jallcom.2016.02.120 ↗
14. Q. Chu, X. Tong, S. Xu, M. Zhang, J. Ji, F. Yan, and C. Yan: J. Mater. Eng. Perform., 2020, vol. 29, pp. 78–86.10.1007/s11665-019-04535-9 ↗
15. J. Ning, L. Zhang, M. Xie, H-Yang, X. Yin, and J. Zhang (2017) J. Alloys Compd., 698, 835–51.10.1016/j.jallcom.2016.12.213 ↗