Microstructure Refinement and Mechanical Properties of 304 Stainless Steel by Repetitive Thermomechanical Processing
Source abstract
Abstract
Repetitive thermomechanical processing (TMP) was applied for evaluating the effect of strain-induced α′-martensite transformation and reversion annealing on microstructure refinement and mechanical properties of 304 austenitic stainless steel. The first TMP scheme consisted of four cycles of tensile deformation to strain of 0.4, while the second TMP scheme applied two cycles of tensile straining to 0.6. For both schemes, tensile tests were conducted at 173 K (− 100 °C) followed by 5-minute annealing at 1073 K (800 °C). The volume fraction of α′-martensite in deformed samples increased with increasing cycles, reaching a maximum of 98 vol pct. Examination of annealed microstructure by electron backscattered diffraction indicated that increasing strain and/or number of cycles resulted in stronger reversion to austenite with finer grain size of 1 μm. Yet, increasing strain reduced the formation of Σ3 boundaries. The annealing textures generally show reversion of α′-martensite texture components to the austenite texture of brass and copper orientations. The increase in strain and/or number of cycles resulted in stronger intensity of copper orientation, accompanied by the formation of recrystallization texture components of Goss, cube, and rotated cube. The reduction in grain size with increasing cycles caused an increase in yield strength. It also resulted in an increase in strain hardening rate during deformation due to the increase in the formation of α′-martensite. The increase in strain hardening rate occurred in two consecutive stages, marked as stages II and III. The strain hardening in stage II is due to the formation of α′-martensite from either austenite or e-martensite, while the stage-III strain hardening is attributed to the necessity to break the α′-martensite-banded structure for forming block-type martensite at high strains.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (63)
Show source-provided references
1. T. Maki: Curr. Opin. Solid. St., 1997, vol. M2, pp. 290-295.10.1016/S1359-0286(97)80117-9 ↗
2. A.K. Raj, J.S. Kumar, and K.A. Padmanabhan: Mater. Lett., 1999, vol. 38, pp. 386-390.10.1016/S0167-577X(98)00194-3 ↗
3. A.F. Padilha, R.L. Plaut, and P.R. Rios: ISIJ Int., 2003, vol. 43, pp. 135-143.10.2355/isijinternational.43.135 ↗
4. S. Takaki, S. Tanimoto, Y. Tokunaga, and K. Tomimura: J. Iron Steel Inst. Jpn., 1988, vol. 74, pp. 1058-1064.10.2355/tetsutohagane1955.74.6_1058 ↗
5. K. Tomimura, S Takaki, and Y. Tokunaga: ISIJ Int., 1991, vol. 31, pp. 1431-1437.10.2355/isijinternational.31.1431 ↗
6. T.J. Angel: J. Iron Steel Inst., 1954, vol. 177, pp.165-174.
7. K. Nohara, Y. Ono, and N. Ohashi: J. Iron Steel Inst. Jpn., 1977, vol. 63, pp. 212-222.
8. R.E. Schramm, and R.P. Reed: Metall. Trans. A, 1975, vol. 6, pp. 1345-1351.10.1007/BF02641927 ↗
9. A. Di Schino, I. Salvatori, and J.M. Kenny: J. Mater. Sci., 2002, vol. 37, pp. 4561-4565.10.1023/A:1020631912685 ↗
10. A. Di Schino, M. Barteri M, and J.M. Kenny: J. Mater. Sci. Lett., 2002, vol. 21, pp. 751-753.10.1023/A:1015757710546 ↗
11. K. Tao, H. Choo, H. Li, B. Clausen, J.E. Jin, and Y.K. Lee: Appl. Phys. Lett., 2007, vol. 90, 101911.10.1063/1.2711758 ↗
12. Y.S. Jung and Y.K. Lee: Scripta Mater., 2008, vol. 59, pp. 47-50.10.1016/j.scriptamat.2008.02.019 ↗
13. D.L. Johannsen, A. Kyröläinen, and P.J. Ferreira: Metall. Trans. A, 2006, vol. 37A, pp. 2325-2338.10.1007/BF02586207 ↗
14. S. Rajasekhara, P.J. Ferreira, L.P. Karjalainen, and A. Kyröläinen: Metall. Trans. A, 2007, vol. 38A, pp. 1202-1210.10.1007/s11661-007-9143-4 ↗
15. R.D.K. Misra, B. Ravi Kumar, M. Somani, and P. Karjalainen: Scripta Mater., 2008, vol. 59, pp. 79–82.10.1016/j.scriptamat.2008.02.028 ↗
16. M. Eskandari, A. Najafizadeh, and A. Kermanpur: Mat. Sci. Eng. A, 2009, vol. 519A, pp. 46-50.10.1016/j.msea.2009.04.038 ↗
17. R.D.K. Misra, S. Nayak, S. Mali, M.C. Somani, and L.P. Karjalainen: Metall. Trans. A, 2009, vol. 40A, pp. 2498-2509.10.1007/s11661-009-9920-3 ↗
18. R.D.K. Misra, S. Nayak, S. Mali, J.S. Shah, M.C. Somani, and L.P. Karjalainen: Metall. Trans. A, 2010, vol. 41A, pp. 3-12.10.1007/s11661-009-0072-2 ↗
19. Y. Ma, J.E. Jin, and Y.K. Lee: Scripta Mater., 2005, vol. 52, pp. 1311-1315.10.1016/j.scriptamat.2005.02.018 ↗
20. J.E. Jin, Y.S. Jung, and Y.K. Lee: Mat. Sci. Eng. A, 2007, vol. 449–451A, pp. 786–89.10.1016/j.msea.2006.02.350 ↗
21. A. Momeni and S.M. Abbasi: J. Mater. Sci. Technol., 2011, vol. 27, pp. 338-343.10.1016/S1005-0302(11)60071-6 ↗
22. P.J. Szabo: Mater. Charact., 2012, vol. 66, pp. 99-103.10.1016/j.matchar.2011.09.003 ↗
23. C.Y. Lee, C.S. Yoo, A. Kermanpur, and Y.K. Lee: J. Alloy Compd., 2014, vol. 583, pp. 357-360.10.1016/j.jallcom.2013.08.161 ↗
24. J. Talonen, P. Aspegren, and H. Hanninen: J. Mater. Sci. Technol., 2004, vol. 20, pp. 1506-1512.10.1179/026708304X4367 ↗
25. A. Hedayati, A. Najafizadeh, A. Kermanpur, and F. Forouzan: J. Mater. Process. Tech., 2010, vol. 210, pp. 1017-1022.10.1016/j.jmatprotec.2010.02.010 ↗
26. V. Shrinivas, S.K. Varma, and L.E. Murr: Metall. Trans. A, 1995, vol. 26A, pp. 661-671.10.1007/BF02663916 ↗
27. A. De, J. Speer, D. Matlock, D. Murdock, M. Mataya, and R. Comstock: Metall. Trans. A, 2006, vol. 37A, pp. 1875-1886.10.1007/s11661-006-0130-y ↗
28. M. Umemoto and W. Owen: Metall. Trans. B, 1974, vol. 5B, pp. 2041-2046.10.1007/BF02644497 ↗
29. J.H. Jun and C.S. Choi: Mat. Sci. Eng. A, 1998, vol. 257, pp. 353-356.10.1016/S0921-5093(98)00994-0 ↗
30. T. Maki, Y. Tomota, and I. Tamura: J. Jpn. Inst. Met., 1974, vol. 38, pp. 871-876.10.2320/jinstmet1952.38.9_871 ↗
31. E. Jimenez-Melero, N. van Dijk, L. Zhao, J. Sietsma, S. Offerman, J. Wright, and S. van der Zwaag: Scripta Mater., 2007, vol. 56, pp. 421-424.10.1016/j.scriptamat.2006.10.041 ↗
32. P.L. Mangonon Jr. and G. Thomas: Metall. Trans., 1970, vol. 1, pp. 1587-1594.10.1007/BF02642004 ↗
33. K.B. Guy, E.P. Butler, and D.R.F. West: Met. Sci., 1983, vol. 17, pp. 167-176.10.1179/030634583790420961 ↗
34. G.B. Olson, and M. Cohen: Metall. Trans. A, 1976, vol. 7, pp. 1897-1904.
35. S. Allain, J.P. Chateau, and O. Bouaziz: Mater. Sci. Eng. A, 2004, vol. 387, pp. 143-147.10.1016/j.msea.2004.01.060 ↗
36. K. Sato, M. Ichinose, Y. Hirotsu, and Y. Inoue: ISIJ Int., 1989, vol. 29, pp. 868-877.10.2355/isijinternational.29.868 ↗
37. M.C. Somani, P. Juntunen, L.P. Karjalainen, R.D.K. Misra, and A. Kyröläinen: Metall. Trans. A, 2009, vol. 40A, pp. 729-744.10.1007/s11661-008-9723-y ↗
38. S.P. Bellier and R.D. Doherty: Acta Metall. Mater., 1977, vol. 25, pp. 521-538.10.1016/0001-6160(77)90192-4 ↗
39. P.L. Mangonon Jr. and G. Thomas: Metall. Trans., 1970, vol. 1, pp.1577-1586.10.1007/BF02642003 ↗
40. P. Chapellier, R.K. Ray, and J.J. Jonas: Acta Metall. Mater., 1990, vol. 38, pp. 1475-1490.10.1016/0956-7151(90)90116-X ↗
41. R.E. Smallman and D. Green: Acta Metall. Mater., 1964, vol. 12, pp. 145-154.10.1016/0001-6160(64)90182-8 ↗
42. S.R. Goodman and H. Hu: Metall. Soc. AIME, 1964, vol. 230, pp. 1413-1419.
43. S.R. Goodman and H. Hu: Metall. Soc. AIME, 1965, vol. 233, pp. 103-110.
44. P.K. De, J.G. Speer, D.K. Matlock, D.C. Murdock, M.C. Mataya, and R.J. Comstock Jr.: Metall. Trans. A, 2006, vol. 37, pp. 1875-1886.10.1007/s11661-006-0130-y ↗
45. B. Ravi Kumar, A.K. Singh, S. Das, and D.K. Bhattacharya: Mat. Sci. Eng. A, 2004, vol. 364A, pp. 132-139.10.1016/j.msea.2003.08.012 ↗
46. S.G. Chowdhury, S. Datta, B. Ravi Kumar, P.K. De, and R.N. Ghosh: Mat. Sci. Eng. A, 2007, vol. 443A, pp. 114-119.10.1016/j.msea.2006.09.059 ↗
47. C. Donadille, R. Valle, P. Dervin, and R. Penelle: Acta Metall. Mater., 1989, vol. 37, pp. 1547-1571.10.1016/0001-6160(89)90123-5 ↗
48. P.A. Beck and H. Hu: Metall. Soc. AIME, 1952, vol. 194, pp. 83-90.
49. E. Nes: J. Mater. Sci., 1978, vol. 13, pp. 2052-2055.10.1007/BF00552917 ↗
50. O. Engler. O: Metall. Trans. A, 1999, vol. 30A, pp. 1517-1527.
51. B. Ravi Kumar, A.K. Singh, B. Mahato, P.K. De, N.R. Bandyopadhyay, and D.K. Bhattacharya: Mat. Sci. Eng. A, 2006, vol. 429A, pp. 205-211.10.1016/j.msea.2006.05.107 ↗
52. S.S. Hecker, M.G. Stout, K.P. Staudhammer, and J.L. Smith: Metall. Trans. A, 1982, vol. 13A, pp. 619-626.10.1007/BF02644427 ↗
53. J. Talonen, P. Nenonen, G. Pape, and H. Hänninen: Metall. Trans. A, 2005, vol. 36A, pp. 421-432.10.1007/s11661-005-0313-y ↗
54. B. Petit, N. Gey, M. Cherkaoui, B. Bolle, and M. Humbert: Int. J. Plasticity, 2007, vol. 23, pp. 323-341.10.1016/j.ijplas.2006.07.002 ↗
55. D. Rouseau, G. Blanc, R. Tricot, A. Gueussier: Mem. Sci. Rev. Met., 1970, vol. 67, pp. 315-334.
56. S.M. Tavares, D. Gunderov, V. Stolyarov, and J.M. Neto: Mat. Sci. Eng. A, 2003, vol. 358A, pp. 32-36.10.1016/S0921-5093(03)00263-6 ↗
57. D. Maréchal: Linkage Between Mechanical Properties and Phase Transformations in a 301LN Austenitic Stainless Steel, Dissertation, 2011, The University of British Columbia, Vancouver, Canada.
58. S. Nanga, A. Pineau, B. Tanguy, L. Nazé, and P.O. Santacreu: Proc. eighth Inter. Conf. Martensitic Transformations, 2009, pp. 341–48.
59. R. Varin, B. Mazurek, and D. Himbeault: Mater. Sci. Eng., 1987, vol. 94, pp. 109–19.10.1016/0025-5416(87)90326-0 ↗
60. A. Kisko, R.D.K. Misra, J. Talonen, L.P. Karjalainen: Mat. Sci. Eng. A, 2013, vol. 578, pp. 408–416.10.1016/j.msea.2013.04.107 ↗
61. K. Spencer: The Work-Hardening of Austenitic Stainless Steel, applied to the Fabrication of High-Strength Conductors, Dissertation, 2004, McMaster University, Canada.
62. C.W. Sinclair, D. Maréchal, and J.D. Mithieux: MATEC Web of Conferences, 2013, vol. 7, 01010.10.1051/matecconf/20130701010 ↗
63. P. Hedström, U. Lienert, J. Almerb, and M. Odén: Scripta Mater., 2007, vol. 56, pp. 213-216.10.1016/j.scriptamat.2006.10.009 ↗