journal article·2022-06

Thin Strip vs Direct Chill Casting: The Effects of Casting Cooling Rate on the As-cast Microstructure of AA6005 Al–Si–Mg Alloy

Shengze Yin, Andrew Howells, David J. Lloyd, Mark Gallerneault, Vahid Fallah

Publisher page

Abstract

Aluminum AA6005 sheet produced by Thin Strip (TS) casting was compared to the slabs produced by Direct Chill casting in the as-cast state. Higher cooling rates experienced before, during, and after the solidification for the TS cast sheet showed a finer grain size, smaller secondary dendritic arm spacing, improved solute supersaturation, and a lack of (hbox {Mg}_{{2}})Si constituents at the grain boundary. These findings showed the effects of cooling rate in the casting process on the as-cast microstructure and provided a basis for further heat-treatment optimization of the TS cast sheet.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. J.T. Stanley and R.E.J. Sanders: Handbook of Aluminum: Alloy Production and Materials Manufacturing, vol. 2, Marcel Dekker, Inc., New York, 2003, pp. 319–42.10.1201/9780429223259-9 ↗
2. W.T. Choate and J.A.S. Green: U.S. Energy Requirements for Aluminum Production: Historical Perspective, Theoretical Limits and New Opportunities, U.S. Department of Energy, 2007, pp. 113–16.
3. Hazelett Strip Casting Corporation: Internal Report, Hazelett Strip Casting Corporation, Colchester, 2017.
4. T. Dorin, A. Vahid, and J. Lamb: Fundamentals of Aluminum Metallurgy: Recent Advances, Elsevier, Kidlington, 2018, pp. 418–19.
5. V. Fallah, D.J. Lloyd, and M. Gallerneault: Mater. Sci. Eng. A, 2017, vol. 698, pp. 88–97.10.1016/j.msea.2017.05.038 ↗
6. H. Qin, V. Fallah, Q. Dong, M. Brochu, M.R. Daymond, and M. Gallerneault: Mater. Charact., 2018, vol. 145, pp. 29–38.10.1016/j.matchar.2018.08.025 ↗
7. H. Qin, Q. Dong, V. Fallah, and M.R. Daymond: Metall. Mater. Trans. A, 2020, vol. 51A, pp. 448–66.10.1007/s11661-019-05505-5 ↗
8. Q. Dong, A. Howells, D.J. Lloyd, M. Gallerneault, and V. Fallah: Mater. Sci. Eng. A, 2020, vol. 772, p. 138693.10.1016/j.msea.2019.138693 ↗
9. Y.S. Park, S.B. Lee, and N.J. Kim: Mater. Trans., 2003, vol. 44, pp. 2617–24.10.2320/matertrans.44.2617 ↗
10. Y. Birol: Mater. Sci. Eng. A, 2005, vol. 391, pp. 175–80.10.1016/j.msea.2004.08.069 ↗
11. K. Suzuki, S. Kumai, Y. Saito, and T. Haga: Mater. Trans., 2005, vol. 46, pp. 2602–08.10.2320/matertrans.46.2602 ↗
12. A. Baserinia, E. Caron, M. Wells, D. Weckman, S. Barker, and M. Gallerneault: Metall. Mater. Trans. B, 2013, vol. 44B, pp. 1017–29.10.1007/s11663-013-9859-z ↗
13. P.L. Schaffer and A.K. Dahle: Mater. Sci. Eng. A, 2005, vol. 413–414, pp. 373–78.10.1016/j.msea.2005.08.202 ↗
14. W. Kurz and D.J. Fisher: Fundamentals of Solidification, Trans Tech Publications, Bach, 1998.10.4028/www.scientific.net/RC.35 ↗
15. V. Rontó and A. Roósz: Int. J. Cast Met. Res., 2001, vol. 14, pp. 131–35.10.1080/13640461.2001.11819431 ↗
16. C. Brito, T.A. Costa, T.A. Vida, F. Bertelli, N. Cheung, J.E. Spinelli, and A. Garcia: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 3342–55.10.1007/s11661-015-2967-4 ↗
17. C. Brito, H. Nguyen-Thi, N. Mangelinck-Noël, N. Cheung, J.E. Spinelli, and A. Garcia: IOP Conf. Ser. Mater. Sci. Eng., 2019, vol. 529, p. 012018.10.1088/1757-899X/529/1/012018 ↗
18. N.C.W. Kuijpers, F.J. Vermolen, K. Vuik, and S. van der Zwaag: Mater. Trans., 2003, vol. 44, pp. 1448–56.10.2320/matertrans.44.1448 ↗
19. P. Priya, D.R. Johnson, and M.J.M. Krane: Metall. Mater. Trans. A, 2016, vol. 47A, pp. 4625–39.10.1007/s11661-016-3610-8 ↗
20. S. Kumar, P.S. Grant, and K.A.Q. O’Reilly: Metall. Mater. Trans. A, 2016, vol. 47A, pp. 3000–14.10.1007/s11661-016-3451-5 ↗
21. N. Bayat, T. Carlberg, and M. Cieslar: J. Alloys Compd., 2017, vol. 725, pp. 504–09.10.1016/j.jallcom.2017.07.149 ↗