The Effects of Defects on Tensile Properties of Cast ADC12 Aluminum Alloy
Source abstract
Abstract
To better understand the effects of cast defects on mechanical properties, cast aluminum alloys with various porosities were used. Porosity in the cast samples was created during the casting process, and to clearly identify the porosity effects on the mechanical properties, artificial defects (porosity-like tiny holes) were created mechanically. The tensile properties for the cast aluminum alloys appear to be attributed to the area fraction of the porosity on the fracture surface (namely, the defect rate, DR), although there were different trends because of the different stress concentrations: the ultimate tensile strength and 0.2 pct proof strength were linearly related to DR, while a non-linear correlation was detected for fracture strain. Even in Al alloys with small amounts of defects, significant reductions in the fracture strain were observed. These results were verified using tensile tests on specimens containing artificial defects. The effects of artificial defects on the tensile properties were further investigated using numerous tiny holes, created in several formations. The artificial defects (several small holes), lined up at perpendicular (90 deg) and 45 deg directions against the loading direction, made significant reductions in the tensile properties, even though only weak defect effects were observed for the 90 deg loading direction. No severe defect effects were obvious for the specimen with a tiny defect of ϕ0.1 mm, because of the lower stress concentration, compared to the microstructural effects in the cast Al alloys: the grain boundaries and the second phases. Such phenomena were clarified using tensile tests on cast samples with differently sized microstructures. There were no clear defect effects on the yield strength as the defect amount was less than 10 pct, and microstructural effects were not detected either in this case. Failure characteristics during tensile loading were revealed directly by in-situ strain observations using high-speed cameras.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. M.A. Irfan, D. Schwam, A. Karve, R. Ryder, Porosity reduction and mechanical properties improvement in die cast engine blocks, Mater. Sci. Eng. A 535(2012)108–114.10.1016/j.msea.2011.12.049 ↗
2. C.H. Caceres, Economical and environmental factors in light alloys automotive applications, Metall. Mater. Trans A 38A(2007)1649–1661.10.1007/s11661-007-9156-z ↗
3. H.R. Ammar, A.M. Samuel, F.H. Samuel, Porosity and the fatigue behavior of hypoeutectic and hypereutectic aluminum-silicon casting alloys, Int. J. Fatigue 30(2008)1024–1035.10.1016/j.ijfatigue.2007.08.012 ↗
4. O. Kuwazuru, Y. Murata, Y. Hangai, T. Utsunomiya, S. Kitahara, N. Yoshikawa, X-ray CT inspection for porosities and its effect on fatigue of die cast aluminum alloy, J. Solid Mech. Mater. Eng. 9(2008)1220–1231.10.1299/jmmp.2.1220 ↗
5. A.K.M. Aziz Ahamed, H. Kato, Influence of casting defects on tensile properties of ADC12 aluminum alloy die-castings, Mater. Trans. JIM 49(2008)1621–1628.10.2320/matertrans.F-MRA2008814 ↗
6. S. Jana, R.S. Mishra, J.B. Baumann, G. Grant, Effect of friction stir processing on fatigue behavior of an investment cast Al–7Si–0.6 Mg alloy, Acta Mater. 58(2010)989–1003.10.1016/j.actamat.2009.10.015 ↗
7. G.W. Mugica, D.O. Tovio, J.C. Cuyas, A.C. Conzátes, Effect of porosity on the tensile properties of low ductility aluminum alloys, Mater. Res. 7(2004)221–229.10.1590/S1516-14392004000200002 ↗
8. H.D. Zhao, F. Wang, Y.Y. Li, W. Xia, Experimental and numerical analysis of gas entrapment defects in plate ADC12 die castings, J. Mater. Process. Technol. 209(2009)4537–4542.10.1016/j.jmatprotec.2008.10.028 ↗
9. C. Kawai, A. Yamakawa, Effect of porosity and microstructure on the strength of Si3N4: designed microstructure for high strength, high thermal shock resistance, and facile machining, J. Am. Ceram. Soc. 80(1997)2705–2708.10.1111/j.1151-2916.1997.tb03179.x ↗
10. J.P. Weiler, J.T. Wood, Modeling fracture properties in a die-cast AM60B magnesium alloy II – The effects of the size and location of porosity determined using finite element simulations, Mater. Sci. Eng. A 527(2009)32–37.10.1016/j.msea.2009.08.061 ↗
11. J.P. Weiler, J.T. Wood, Modeling fracture properties in a die-cast AM60B magnesium alloy I – Analytical failure model, Mater. Sci. Eng. A 527(2009)25–31.10.1016/j.msea.2009.08.060 ↗
12. C.H. Cáceres, B.I. Selling, Casting defects and the tensile properties of an Al-Si-Mg alloy, Mater. Sci. Eng. A 220(1996)109–116.10.1016/S0921-5093(96)10433-0 ↗
13. M. Avalle, G. Belingardi, M.P. Cavatorta, R. Doglione, Casting defects and fatigue strength of a die cast aluminum alloy: a comparison between standard specimens and production components, Int. J. Fatigue 24(2002)1–9.10.1016/S0142-1123(01)00112-8 ↗
14. M. Okayasu, S. Takeuchi, M. Yamamoto, H. Ohfuji, Precise analysis of microstructural effects on mechanical properties of cast ADC12 aluminum alloy, Metall. Mater. Trans A, 46A(2015)1597–1609.10.1007/s11661-015-2747-1 ↗
15. M. Okayasu, S. Takasu, M. Mizuno, Relevance of instrumented nano-indentation for the assessment of the mechanical properties of eutectic crystals and α-Al grain in cast aluminum alloys, J. Mater. Sci. 47(2012)241–250.10.1007/s10853-011-5791-2 ↗
16. W.C. Oliver, G.M. Pharr, Measurement of harness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology, J. Mater. Res. 19(2004)3–20.10.1557/jmr.2004.19.1.3 ↗
17. A. Ueno, S. Miyakawa, K. Yamada, T. Sugiyama, Fatigue behavior of die casting aluminum alloys in air and vacuum, Procedia Eng. 2(2010)1937–1943.10.1016/j.proeng.2010.03.208 ↗
18. Q. Yan, H. Yu, Z. Xu, B. Xiong, C. Cai, Effect of holding pressure on the microstructure of vacuum counter-pressure casting aluminum alloy, J. Alloy. Comp. 501(2010)352–357.10.1016/j.jallcom.2010.04.103 ↗
19. M. Okayasu, Y. Ohkura, S. Takeuchi, S. Takasu, H. Ohfuji, T. Shiraishi, A study of the mechanical properties of an Al-Si-Cu alloy (ADC12) produced by various casting processes, Mater. Sci. Eng. A 543(2012)185–192.10.1016/j.msea.2012.02.073 ↗
20. N. Nakata, Y.G. Kim, H. Fujii, T. Tsumura, T. Komazaki, Improvement of mechanical properties of aluminum die casting alloy by multi-pass friction stir processing, Mater. Sci. Eng. A 437(2006)274–280.10.1016/j.msea.2006.07.150 ↗