Correlation Between Texture, Grain Boundary Constitution, and Corrosion Behavior of Ni-Cu Coatings
Source abstract
Abstract
Nickel-Copper (Ni-Cu) coating with different Cu contents (2 to 7 wt pct) was electrodeposited over a mild steel substrate. Corrosion properties of these coatings were studied in 3.5 wt pct NaCl solution by electrochemical impedance spectroscopy (EIS) techniques and weight loss measurements, and the results obtained were correlated with the microstructure of the coatings. The results revealed that the Ni-2wt pct Cu coating yields the best corrosion protection performance when compared to the pure Ni, Ni-4wt pct Cu, and Ni-7wt pct Cu coatings with relatively lower corrosion resistance. Ni-7wt pct Cu coatings exhibited the lowest corrosion resistance performance. The coating morphology micrographs showed that the initial incorporation of Cu (2 wt pct) into the Ni matrix produced a compact, uniform, and crack-free morphology. The coating micro-texture study conducted using the electron backscatter diffraction (EBSD) technique showed an increase in the low-angle grain boundaries (LAGBs) with a relatively higher fraction of Σ3 CSLs (special boundaries) for the Ni-2wt pct Cu coating. LAGBs are low-energy grain boundaries, and thus, a higher fraction of LAGBs leads to increased corrosion resistance. Ni-7wt pct Cu coatings contained the highest percentage of high-angle grain boundaries (HAGBs), which yielded the highest corrosion rate for this coating.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electrodeposition and Electroless Coatings · Corrosion Behavior and Inhibition · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. M. Alper, H. Kockar, M. Safak, and M. Celalettin Baykul: J. Alloys Compd., 2008, vol. 453, pp. 15–19.10.1016/j.jallcom.2006.11.066 ↗
2. E. Pellicer, A. Varea, S. Pané, B.J. Nelson, E. Menendez, M. Estrader, S. Surinach, M.D. Baro, J. Nogues, and J. Sort: Adv. Funct. Mater., 2010, vol. 20, pp. 983–91.10.1002/adfm.200901732 ↗
3. S. Mukherjee and A.K. Ghosh: Mat. Sci. Eng. A., 2011, vol. 528, pp. 3289–94.10.1016/j.msea.2011.01.063 ↗
4. A.A. Khadoma and A.S. Yarob: Russ. J. Phys. Chem., 2011, vol. 85, pp. 2005–12.10.1134/S0036024411110148 ↗
5. U.S. Mohanty: J. Appl. Electrochem., 2011, vol. 41, pp. 257–70.10.1007/s10800-010-0234-3 ↗
6. C.M.O. Brett, A.M.O. Brett: Oxford University Press, Oxford, 1994.
7. A. Aliyu and C. Srivastava: J. Alloys Compd., 2020, vol. 821, p. 153560.10.1016/j.jallcom.2019.153560 ↗
8. U. Erb: Nanostruct. Mater., 1995, vol. 6, pp. 533–38.10.1016/0965-9773(95)00114-X ↗
9. M. Metikos-Hukovic, I. Skugorb, Z. Gruba, and R. Babi: Electrochim. Acta., 2010, vol. 55, p. 3123.10.1016/j.electacta.2010.01.066 ↗
10. W.A. Badawy, K.M. Ismail, and A.M. Fathi: Electrochim. Acta., 2005, vol. 50, p. 3603.10.1016/j.electacta.2004.12.030 ↗
11. K.M. Ismail, A.M. Fathi, and W.A. Badawy: Corros. Sci., 2006, vol. 48, p. 1912.10.1016/j.corsci.2005.07.004 ↗
12. I. Baskaran, T.S.N. Sankara Narayanan, and A. Stephen: Mater. Lett., 2006, vol. 60, pp. 1990–95.10.1016/j.matlet.2005.12.065 ↗
13. S.K. Ghosh, A.K. Grover, G.K. Dey, and M.K. Totlania: Surf. Coat. Technol., 2000, vol. 126, pp. 48–63.10.1016/S0257-8972(00)00520-X ↗
14. M. Cherkaoui, E. Chassaing, and K.V. Quang: Surf. Coat. Technol., 1988, vol. 34, pp. 243–52.10.1016/0257-8972(88)90116-8 ↗
15. M.B. Khashayar, N. Pooria, and P. Mahmoud: Iran. J. Chem. Chm. Eng., 2018, vol. 37, pp. 117–27.
16. M. Srivastava, V. Ezhil Selvi, V.K. WilliamGrips, and K.S. Rajam: Surf. Coat. Technol., 2006, vol. 201, pp. 3051–60.10.1016/j.surfcoat.2006.06.017 ↗
17. B. Bakhit and A. Akbari: J. Coat. Technol. Res., 2013, vol. 10, pp. 285–95.10.1007/s11998-012-9437-3 ↗
18. A. Aliyu, K. Sai Jyotheender, and C. Srivastava: Surf. Coat. Technol., 2021, vol. 412, p. 127079.10.1016/j.surfcoat.2021.127079 ↗
19. K.S. Jyotheender and C. Srivastava: Composite B., 2019, vol. 175, p. 107145.10.1016/j.compositesb.2019.107145 ↗
20. S.R.F. Lala, K.S. Jyotheender, A. Gupta, S. Arora, M.K. Punith Kumar, and C. Srivastava: Materialia., 2020, vol. 14, p. 100944.10.1016/j.mtla.2020.100944 ↗
21. T. Watanabe: Res. Mech., 1984, vol. 11, pp. 47–84.
22. K.T. Aust, U. Erb, and G. Palumbo: Mater. Sci. Eng. A, 1994, vol. 176, pp. 329–34.10.1016/0921-5093(94)90995-4 ↗
23. P. Lin, G. Palumbo, U. Erb, and K.T. Aust: Scr. Metall. Mater., 1995, vol. 33, pp. 1387–92.10.1016/0956-716X(95)00420-Z ↗
24. R. Ishibashi, T. Horiuchi, J. Kuniya, M. Yamamoto, S. Tsurekawa, H. Kokawa, T. Watanabe, and T. Shoji: Mater. Sci. Forum., 2005, vol. 475–479, pp. 3863–66.10.4028/www.scientific.net/MSF.475-479.3863 ↗
25. S. Tsurekawa, S. Nakamichi, and T. Watanabe: Acta Mater., 2006, vol. 54, pp. 3617–26.10.1016/j.actamat.2006.03.048 ↗
26. H. Kokawa, M. Shimada, Z.J. Wang, Y.S. Sato, and M. Michiuchi: Key Eng. Mat., 2004, vol. 261–263, pp. 1005–10.10.4028/www.scientific.net/KEM.261-263.1005 ↗
27. B.B. Strraumal, O.A. Kogtenkova, A.B. Straumal, and B. Baretzky: Lett. Mater., 2018, vol. 8, pp. 364–71.10.22226/2410-3535-2018-3-364-371 ↗
28. A.J. Henrie, B.L. Adams, and R.J. Larsen: Mater. Sci. Forum., 2002, vol. 408–412, pp. 419–24.10.4028/www.scientific.net/MSF.408-412.419 ↗
29. V.Y. Gertsman and S.M. Bruemmer: Acta Mater., 2001, vol. 49, pp. 1589–98.10.1016/S1359-6454(01)00064-7 ↗
30. B. Li, T. Mei, D. Li, S. Du, and W. Zhang: J. Alloys Compd., 2019, vol. 804, pp. 192–201.10.1016/j.jallcom.2019.06.381 ↗
31. M. Alizadeh and H. Safaei: Appl. Surf. Sci., 2018, vol. 456, pp. 195–203.10.1016/j.apsusc.2018.06.095 ↗
32. A. Aliyu, C. Srivastava: Materilia, 2019, vol. 5, pp. 100249.10.1016/j.mtla.2019.100249 ↗
33. N. Zakerin and K.M. Behbahani: Metall. Mater. Trans. A., 2021, vol. 52A, pp. 3247–56.10.1007/s11661-021-06283-9 ↗
34. A. Aliyu and C. Srivastava: Thin Solid Films., 2019, vol. 686, p. 137434.10.1016/j.tsf.2019.137434 ↗
35. A. Aliyu and C. Srivastava: Materilia., 2019, vol. 8, p. 100459.10.1016/j.mtla.2019.100459 ↗
36. A. Aliyu and C. Srivastava: Surf. Coat. Technol., 2020, vol. 405, p. 126596.10.1016/j.surfcoat.2020.126596 ↗
37. K.M. Behbanani, N. Zakerin, P. Najafisayar, and M. Pakshir: Corros. Sci., 2021, vol. 183, p. 109340.10.1016/j.corsci.2021.109340 ↗
38. M.Y. Rekha and C. Srivastava: Corros. Sci., 2019, vol. 152, pp. 234–48.10.1016/j.corsci.2019.03.015 ↗
39. A.P. Zhilyaev, B.K. Kim, N.V. Nurislamova, M.D. Baro, J.A. Szpunar, and T.G. Langdon: Scr. Mater., 2002, vol. 46, pp. 575–80.10.1016/S1359-6462(02)00018-0 ↗
40. P.P. Bhattacharjee, S.K. Sinha, and A. Upadhyaya: Scr. Mater., 2007, vol. 56, pp. 13–16.10.1016/j.scriptamat.2006.09.003 ↗
41. A. Clair, M. Foucault, O. Calonne, Y. Lacroute, L. Markey, M. Salazar, V. Vignal, and E. Finot: Acta Mater., 2011, vol. 59, pp. 3116–23.10.1016/j.actamat.2011.01.051 ↗
42. C. Cayron: Acta Mater., 2011, vol. 59, pp. 252–62.10.1016/j.actamat.2010.09.029 ↗
43. S.H. Kim, U. Erb, K.T. Aust, and G. Palumbo: Scr. Mater., 2001, vol. 44, pp. 835–39.10.1016/S1359-6462(00)00682-5 ↗
44. P. Jakupi, J.J. Noel, and D.W. Shoesmith: Electrochem. Solid-State Lett., 2009, vol. 13, pp. C1–C3.10.1149/1.3272851 ↗
45. D. An, T.A. Griffiths, P. Konijnenberg, S. Mandal, Z. Wang, and S. Zaefferer: Acta Mater., 2018, vol. 156, pp. 297–309.10.1016/j.actamat.2018.06.044 ↗
46. L.P. Lehman, Y. Xing, T.R. Bieler, and E.J. Cotts: Acta Mater., 2010, vol. 58, pp. 3546–56.10.1016/j.actamat.2010.01.030 ↗
47. Y.N. Wen and J.M. Zhang: Solid State Commun., 2007, vol. 144, pp. 163–67.10.1016/j.ssc.2007.07.012 ↗
48. K.S. Jyotheender, A. Gupta, and C. Srivastava: Materialia., 2020, vol. 9, p. 100617.10.1016/j.mtla.2020.100617 ↗
49. Y. Yuan, Y. Jiang, J. Zhou, G. Liu, and X. Ren: Mater. Lett., 2019, vol. 253, pp. 424–26.10.1016/j.matlet.2019.07.125 ↗
50. Z.L. Ma, J.W. Xian, S.A. Belyakov, and C.M. Gourlay: Acta Mater., 2018, vol. 150, pp. 281–94.10.1016/j.actamat.2018.02.047 ↗