journal article·2013-03

Fatigue Crack Growth Analysis Under Spectrum Loading in Various Environmental Conditions

S. Mikheevskiy, G. Glinka, E. Lee

Publisher page

Abstract

The fatigue process consists, from the engineering point of view, of three stages: crack initiation, fatigue crack growth, and the final failure. It is also known that the fatigue process near notches and cracks is governed by local strains and stresses in the regions of maximum stress and strain concentrations. Therefore, the fatigue crack growth can be considered as a process of successive crack increments, and the fatigue crack initiation and subsequent growth can be modeled as one repetitive process. The assumptions mentioned above were used to derive a fatigue crack growth model based, called later as the UniGrow model, on the analysis of cyclic elastic–plastic stresses–strains near the crack tip. The fatigue crack growth rate was determined by simulating the cyclic stress–strain response in the material volume adjacent to the crack tip and calculating the accumulated fatigue damage in a manner similar to fatigue analysis of stationary notches. The fatigue crack growth driving force was derived on the basis of the stress and strain history at the crack tip and the Smith–Watson–Topper (SWT) fatigue damage parameter, D = σmaxΔe/2. It was subsequently found that the fatigue crack growth was controlled by a two-parameter driving force in the form of a weighted product of the stress intensity range and the maximum stress intensity factor, ΔKpKmax1−p. The effect of the internal (residual) stress induced by the reversed cyclic plasticity has been accounted for and therefore the two-parameter driving force made it possible to predict the effect of the mean stress including the influence of the applied compressive stress, tensile overloads, and variable amplitude spectrum loading. It allows estimating the fatigue life under variable amplitude loading without using crack closure concepts. Several experimental fatigue crack growth datasets obtained for the Al 7075 aluminum alloy were used for the verification of the proposed unified fatigue crack growth model. The method can be also used to predict fatigue crack growth under constant amplitude and spectrum loading in various environmental conditions such as vacuum, air, and corrosive environment providing that appropriate limited constant amplitude fatigue crack growth data obtained in the same environment are available. The proposed methodology is equally suitable for fatigue analysis of smooth, notched, and cracked components.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Non-Destructive Testing Techniques · Ultrasonics and Acoustic Wave Propagation

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. G. R. Irwin: in Handbuch der Physik, S. Flügge, ed., Springer, Berlin, 1958.
2. J.R. Rice and G.F. Rosengren, Journal of Mechanics and Physics of Solids, 1968, vol. 16, no. 4, pp. 1-12.10.1016/0022-5096(68)90013-6 ↗
3. J.W. Hutchinson, Journal of Mechanics and Physics of Solids, 1968, vol. 16, no. 4, pp. 13.10.1016/0022-5096(68)90014-8 ↗
4. Y.H. Tai and J.R. Yates: Int. Conf. on Characterization of Crack Tip Stress Fields, Forni di Sopra (UD), Italy, March 7–9, 2011, pp. 230–35.
5. M. Croft, Z. Zhong, N. Jisrawi, I. Zakharchenko, R.L. Holtz, J. Skaritka, T. Fast, K. Sadananda, M. Lakshmipathy, and T. Tsakalakos: Int. J. Fatigue, 2005, vol. 27, pp. 1408-1419.10.1016/j.ijfatigue.2005.06.022 ↗
6. A. Livne, E. Bouchbinder, I. Svetlizky, and J. Fineberg (2010) Science 327(5971):1359-1363.10.1126/science.1180476 ↗
7. P.J. Withers, H. Dai, and P. Lopez-Crespo: Int. Conf. on Characterization of Crack Tip Stress Fields, Forni di Sopra (UD), Italy, March 7–9, 2011.
8. R. Jones, M. Krishnapillai, K. Cairns, and N. Matthews: Fatigue Fract. Engng. Mater. Struct, 2010, vol. 33, pp. 871–884.10.1111/j.1460-2695.2010.01505.x ↗
9. J. Zhang , X.D. He, B. Suo, and S.Y. Du, Engineering Fracture Mechanics, vol. 75, 2008, pp. 5217-5228.10.1016/j.engfracmech.2008.08.006 ↗
10. G. Glinka, A. Buczynski: Int. Conf. on Characterization of Crack Tip Stress Fields, Forni di Sopra (UD), Italy, March 7–9, 2011.
11. J.C. Newman (1981) Methods and Models for Predicting Fatigue Crack Growth under Random Loading. ASTM, Philadelphia, pp. 53–84.10.1520/STP28334S ↗
12. A.H. Noroozi, G. Glinka, and S. Lambert, Int. Journal of Fatigue, vol. 27, 2005, pp 1277–1296.10.1016/j.ijfatigue.2005.07.002 ↗
13. A.H. Noroozi, G. Glinka, and S. Lambert, Int. Journal of Fatigue, vol. 29, 2007, pp. 1616–1633.10.1016/j.ijfatigue.2006.12.008 ↗
14. S. Mikheevskiy and G. Glinka, Int. Journal of Fatigue, vol. 31, 2009, pp. 1828–1836.10.1016/j.ijfatigue.2009.02.035 ↗
15. S. Mikheevskiy, G. Glinka, D. Algera, Int. Journal of Fatigue, vol. 42, 2012, pp. 88-94.10.1016/j.ijfatigue.2011.07.006 ↗
16. C.C. Osgood, Fatigue Design, Pergamon Press, New York, 1982.
17. L. Coffin (1954) Trans Am Soc Mech Eng 76:931-50.10.1115/1.4015020 ↗
18. S.S. Manson, G.R. Halford (2006) Fatigue and Durability of Structural Materials. ASM International, Materials Park, Ohio.10.31399/asm.tb.fdsm.9781627083447 ↗
19. K.N. Smith, P. Watson, and T.H. Topper, Journal of Materials, vol. 5, No. 4, 1970. Pp. 767-778.
20. H. Neuber, Journal of Applied Mechanics, ASME, vol. 28, 1961, pp. 544-550.10.1115/1.3641780 ↗
21. A. Moftakhar, A. Buczynski, and G. Glinka, International Journal of Fracture, vol. 70, 1995, pp. 357-373.10.1007/BF00032453 ↗
22. M.N.K. Singh, G. Glinka, and R.N. Dubey, International Journal of Fracture, vol. 76, 1996, pp. 39-60.10.1007/BF00034029 ↗
23. Glinka, G. and Shen, G., Eng. Fracture Mechanics, Vol. 40, No. 6, 1991, pp, 1135-1146.10.1016/0013-7944(91)90177-3 ↗
24. Z. Wu, G. Glinka, H. Jakubczak, and L. Nilsson, Journal of ASTM International, Vol. 1, No. 9, 2004, pp. 1-14.10.1520/JAI19055 ↗
25. N. Louat, K. Sadananda, M. Duesbery, and A.K. Vasudevan, Scripta Metall, 1993, vol. 28, pp. 65–70.10.1016/0956-716X(93)90538-4 ↗
26. E.K. Walker (1970) Effect of Environment and Complex Load History on Fatigue Life. ASTM STP, Philadelphia, pp. 1–14.10.1520/STP32032S ↗
27. S. Dinda and D. Kujawski: Eng. Fracture Mechanics, 2004, vol. 71, no. 12, pp. 1779-1790.10.1016/j.engfracmech.2003.06.001 ↗
28. Mikheevskiy, PhD Thesis, University of Waterloo, 2009.
29. M. Creager and P.C. Paris: Int. J. Fracture, 1967, vol. 3, pp. 247–251.10.1007/BF00182890 ↗
30. E. U. Lee , G. Glinka, A.K. Vasudevan, N. Iyyer, and N.D. Phan: Int. J. Fatigue, 2009, vol. 31, pp. 1858–1864.10.1016/j.ijfatigue.2008.11.013 ↗
31. P.S. Pao: Naval Research Laboratory, Washington, DC, private communication, 2011.