Microstructure, Hardness, and Residual Stress Distributions in T-Joint Weld of HSLA S500MC Steel
Source abstract
Abstract
This paper investigates the characterization of the microstructure, hardness, and residual stress distributions of MIG-welded high-strength low-alloy S500MC steel. The T-joint weld for 10-mm-thick plates was joined using a two passes MIG welding technology. The contour method was performed to measure longitudinal welding residual stress. The obtained results highlighted a good correlation between the metallurgical phase constituents and hardness distribution within the weld zones. In fact, the presence of bainite and smaller ferrite grain size in the weld-fusion zone might be the reason for the highest hardness measured in this region. A similar trend of the residual stress and hardness distributions was also obtained.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Microstructure and Mechanical Properties of Steels · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. [1] M. Manganello: ISS-AIME, Warrendale, PA, 1992, pp.331-343.
2. [2] R. Oyyaravelu, P. Kuppan, N. Arivazhagan: Journal of Advanced Research, 2016, vol. 7, pp. 463–472.10.1016/j.jare.2016.03.005 ↗
3. B. Scholtes and W. Zinn: Handbook of Residual Stress and Deformation of Steel, ASM International, 2002, pp. 391–69.
4. J. Lu: Handbook on Residual Stresses. Manufacturing and Materials Processing, 2nd ed., 2005.
5. S. Maddox: Fatigue Strength of Welded Structures, 2nd ed., Woodhead Publishing, Cambridge, 1991.
6. [6] C. Zhang, S. Vyver, X. Hu, P. Lu: Eng. Fracture Mech., 2011, vol. 78, pp. 1862-1875.10.1016/j.engfracmech.2011.03.004 ↗
7. [7] D. Thibault, P. Bocher, M. Thomas: J. Mater. Process. Technol., 2009, vol. 209, pp. 2195–2202.10.1016/j.jmatprotec.2008.05.005 ↗
8. [8] R.S. Coelho, M. Corpas, J.A. Moreto, A. Jahn, J. Standfuß, A. Kaysser-Pyzalla, H. Pinto: Mater. Sci. Eng. A., 2013, vol. 578, pp. 125–133.10.1016/j.msea.2013.04.039 ↗
9. [9] H. Alipooramirabada, R. Ghomashchia, A. Paradowskab, M. Reid: Journal of Materials Processing Technology, 2016, vol. 231, pp. 456–467.10.1016/j.jmatprotec.2016.01.020 ↗
10. [10] S. Ragu Nathan, V. Balasubramanian, S. Malarvizhi, A.G. Rao: Defence Technology 11, 2015, pp. 308-317.10.1016/j.dt.2015.06.001 ↗
11. A.Z. DeWald and M.R. Hill: University of California, Davis Report for Los Alamos National Laboratory, 2001.
12. M. Turski, E. Lyndon, J. Jon, J.B. Peter, S. Mike, and J.W. Philip: ICPVT-11 Conference, American Society of Mechanical Engineers, New York (USA), 2006.
13. [13] Y. Zhang, S. Ganguly, L. Edwards, M. E. Fitzpatrick: Acta Materialia, 2004, vol. 52 (17), pp. 5225-5232.10.1016/j.actamat.2004.07.045 ↗
14. [14] M. B. Prime, R. J. Sebring, J. M. Edwards, D. J. Hughes, P. J. Webster: Experimental Mechanics, 2004, vol. 44 (2), pp. 176-184.10.1007/BF02428177 ↗
15. [15] M. E. Kartal, C. D. M. Liljedahl, S. Gungor, L. Edwards, M. E. Fitzpatrick: Acta Materialia, 2008, vol. 56, no. 16, pp. 4417-4428.10.1016/j.actamat.2008.05.007 ↗
16. CETIM S., ed., Mécano-soudage, Fabrication. [S.I.], Centre technique des industries mécaniques, France, 1983.
17. [17] D. Thibault, P. Bocher, M. Thomas, M. Gharghouri, M. Côté: Materials Science and Engineering A, 2010,Vol 527, pp. 6205–6210.10.1016/j.msea.2010.06.035 ↗
18. [18] M. B. Prime: J. Eng. Mater. Technol., 2001, vol. 123, pp. 162-168.10.1115/1.1345526 ↗
19. [19] V. Richter-Trummer, S. M. O. Tavares, P. M. G. P. Moreira, M. A. V. De Figueiredo, P. M. S. T. De Castro, Ciência e Tecnologia dos Materiais., 2008, vol. 20, pp. 114-119.
20. [20] H. F. Bueckner: Transactions ASME, 1958, vol. 80, pp. 1225-1230.
21. [21] W. Cheng, L. Finnie, M. Gremaud, and M. B. Prime: Journal of Engineering Materials and Technology, 1994, vol. 116 (1), pp. 1-7.10.1115/1.2904251 ↗
22. R. Fisher: http://pwlinda.mt.umist.ac.uk/contourmethod/links/GJ_PhD, 2005.
23. [23] Y. Traore, S. Paddea, P. Bouchard, M. Gharghouri: Experimental Mechanics, 2013, vol. 53, pp. 605-618.10.1007/s11340-012-9672-7 ↗
24. [24] P. Frankel, M. Preuss, A. Steuwer, P. Withers, S. Bray: Materials Science and Technology, 2009, vol. 25 (4), pp. 640-650.10.1179/174328408X332825 ↗
25. ABAQUS 6.12 Analysis User’s Manual, 2012.
26. [26] B.D. Cullity: Elements of x-ray diffraction. 2nd ed. New York: Addison-Wesley. 1978.
27. I.C. Noyan, J.B. Cohen: Residual Stress: Measurement by Diffraction and Interpretation. Materials Research and Engineering, Springer, New York 1987.10.1007/978-1-4613-9570-6 ↗