journal article·2016-09

Heat-to-Heat Variation in Creep Life and Fundamental Creep Rupture Strength of 18Cr-8Ni, 18Cr-12Ni-Mo, 18Cr-10Ni-Ti, and 18Cr-12Ni-Nb Stainless Steels

Fujio Abe

Publisher page

Abstract

Metallurgical factors causing the heat-to-heat variation in time to rupture have been investigated for 300 series stainless steels for boiler and heat exchanger seamless tubes, 18Cr-8Ni (JIS SUS 304HTB), 18Cr-12Ni-Mo (JIS SUS 316HTB), 18Cr-10Ni-Ti (JIS SUS321 HTB), and 18Cr-12Ni-Nb (JIS SUS 347HTB), at 873 K to 1023 K (600 °C to 750 °C) using creep rupture data for nine heats of the respective steels in the NIMS Creep Data Sheets. The maximum time to rupture was 222,705.3 hours. The heat-to-heat variation in time to rupture of the 304HTB and 316HTB becomes more significant with longer test durations at times above ~10,000 hours at 973 K (700 °C) and reaches to about an order of magnitude difference between the strongest and weakest heats at 100,000 hours, whereas that of the 321HTB and 347HTB is very large of about an order of magnitude difference from a short time of ~100 hours to long times exceeding 100,000 hours at 873 K to 973 K (600 °C to 700 °C). The heat-to-heat variation in time to rupture is mainly explained by the effect of impurities: Al and Ti for the 304HTB and 316HTB, which reduces the concentration of dissolved nitrogen available for the creep strength by the formation of AlN and TiN during creep, and boron for the 347HTB, which enhances fine distributions of M23C6 carbides along grain boundaries. The heat-to-heat variation in time to rupture of the 321HTB is caused by the heat-to-heat variation in grain size, which is inversely proportional to the concentration of Ti. The fundamental creep rupture strength not influenced by impurities is estimated for the steels. The 100,000 hours-fundamental creep rupture strength of the 347HTB steel is lower than that of 304HTB and 316HTB at 873 K and 923 K (600 °C and 650 °C) because the slope of stress vs time to rupture curves is steeper in the 347HTB than in the 304HTB and 316HTB. The 100,000 hours-fundamental creep rupture strength of the 321HTB exhibits large variation depending on grain size.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Nuclear Materials and Properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. Series of NIMS (formerly NRIM) Creep Data Sheets No. 1-55. Tokyo, Tsukuba, National Institute for Materials Science, 2015.
2. 2. F. Abe: Int. J. Pressure Vessels and Piping, 2008, vol. 85, pp. 99-107.10.1016/j.ijpvp.2007.06.005 ↗
3. NIMS Creep Data Sheets No. 3B. Tokyo, Tsukuba, Japan, National Institute for Materials Science, 1986.
4. NIMS Creep Data Sheets, No. 43A, Tokyo, Tsukuba, Japan, National Institute fort Materials Science, 2014.
5. NIMS Creep Data Sheets, No. 4B, Tokyo, Tsukuba, Japan, National Institute fort Materials Science, 1986.
6. F. Abe, H. Tanaka, M. Murata, H. Irie and K. Yagi: Proc. of 4 th Japan-China Bilateral Symp. on High Temp. Strength of Mater., June 2001, Tsukuba, Japan, pp. 83–88.
7. 7. H. Miyazaki, H. Tanaka, M. Murata and F. Abe: J. Jpn Inst. Metals, 2002, vol. 66, pp. 1278-1286.10.2320/jinstmet1952.66.12_1278 ↗
8. 8. F. Abe: Intern. J. Pressure Vessels and Piping, 2010, vol. 87, pp. 310-318.10.1016/j.ijpvp.2010.03.014 ↗
9. S. J. Brett, J. S. Bates and R. C. Thomson: Proc. of Fourth International Conference on Advances in Materials Technology for Fossil Power Plants, October 2004, Hilton Head, North Carolina, USA, pp. 202–16.
10. S. J. Brett (2007) Energy Mater. 2:117-121.10.1179/174892407X266707 ↗
11. 11. H. Naoi, M. Ohgami, X. Liu and T. Fujita: Met. Matri. Trans. A, 1997, vol. 28A, pp. 1195-1203.10.1007/s11661-997-0284-2 ↗
12. 12. N. Shinya, J. Kyono, H. Tanaka, M. Murata and S. Yokoi: Tetsu-To-Hagane, 1983, vol. 69, pp.1668-75.10.2355/tetsutohagane1955.69.14_1668 ↗
13. 13. N. Shinya, H. Tanaka, M. Murata, J. Kyono and S. Yokoi: Tetsu-To-Hagane, 1985, vol. 71, pp. 114-120.10.2355/tetsutohagane1955.71.1_114 ↗
14. NIMS Creep Data Sheets, No. 6B, Tokyo, Tsukuba, Japan, National Institute fort Materials Science, 2000.
15. NIMS Creep Data Sheets, No. 5B, Tokyo, Tsukuba, Japan, National Institute fort Materials Science, 1987.
16. NIMS Creep Data Sheets, No. 28B, Tokyo, Tsukuba, Japan, National Institute fort Materials Science, 2001.
17. 17. R. K. Winge, V. A. Fassel, V. J. Peterson and M. A. Floyd: Inductively Coupled Plasma-Atomic Emission Spectroscopy, Elsevier, Amsterdam, 1985, pp. 1-25.
18. JIS G 0551: Steels – Micrographic Determination of the Apparent Grain Size, Japanese Industrial Standard, 2013.
19. ASTM E112: Standard Test Methods for Determining Average Grain Size, Annual Book of ASTM Standards, 2005.
20. 20. H. Tanaka, M. Murata and N. Shinya: Tetsu-To-Hagane, 1992, vol. 78, pp. 934-940.10.2355/tetsutohagane1955.78.6_934 ↗
21. 21. H. Tanaka, M. Murata, F. Abe and K. Yagi: Mat. Sci. Eng., 1997, vol. A234-236, pp. 1049-1052.10.1016/S0921-5093(97)00360-2 ↗
22. Metallographic Atlas of Long-Term Crept Materials, M-1, Tokyo, Tsukuba, National Institute fort Materials Science, 1999.
23. Metallographic Atlas of Long-Term Crept Materials, M-2, Tokyo, Tsukuba, National Institute fort Materials Science, 2003.
24. Metallographic Atlas of Long-Term Crept Materials, M-5, Tokyo, Tsukuba, National Institute fort Materials Science, 2006.
25. Metallographic Atlas of Long-Term Crept Materials, M-3, Tokyo, Tsukuba, National Institute fort Materials Science, 2004.
26. 26. H. Tanaka, M. Murata, F. Abe and K. Yagi: Tetsu-to-Hagane, 1997, vol. 83, pp. 72-77.10.2355/tetsutohagane1955.83.1_72 ↗
27. 27. F. H. Froes, M. G. H. Wells and B. R. Banerjee: Metal Sci. J., 1968, vol. 2, pp. 232-234.10.1179/030634568790443134 ↗
28. 28. T. Matsuo, T. Shinoda and R. Tanaka: Tetsu-to-Hagane, 1973, vol.59, pp. 907-91810.2355/tetsutohagane1955.59.7_907 ↗
29. 29. K. Yoshikawa, H. Fujikawa, H. Teranishi, H. Yuzawa and M. Kubota: The thermal and nuclear power, 1985, vol. 36, pp. 1325-1339.
30. 30. Y. Minami and H. Kimura: Trans. ISIJ, 1987, vol. 27, pp. 299-301.10.2355/isijinternational1966.27.299 ↗
31. 31. R. Tanaka and T. Shinoda: J Soc Mater Sci Japan, 1972, vol. 21, pp. 198-203.10.2472/jsms.21.198 ↗