journal article·2013-12

Development of a 3D Filling Model of Low-Pressure Die-Cast Aluminum Alloy Wheels

Jianglan Duan, Daan Maijer, Steve Cockcroft, Carl Reilly

Publisher page

Abstract

A two-phase computational fluid dynamics model of the low-pressure die-cast process for the production of A356 aluminum alloy wheels has been developed to predict the flow conditions during die filling. The filling model represents a 36-deg section of a production wheel, and was developed within the commercial finite-volume package, ANSYS CFX, assuming isothermal conditions. To fully understand the behavior of the free surface, a novel technique was developed to approximate the vent resistances as they impact on the development of a backpressure within the die cavity. The filling model was first validated against experimental data, and then was used to investigate the effects of venting conditions and pressure curves during die filling. It was found that vent resistance and vent location strongly affected die filling time, free surface topography, and air entrainment for a given pressure fill-curve. With regard to the pressure curve, the model revealed a strong relation between the pressure curve and the flow behavior in the hub, which is an area prone to defect formation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. B. Zhang, D.M. Maijer, S.L. Cockcroft, Mater. Sci. Eng. A 464A (2007) 295–305.
2. B. Zhang, S. Cockcroft, D. Maijer, J. Zhu, A. Phillion, JOM 57 (2005) 36-43.10.1007/s11837-005-0025-1 ↗
3. M. Okayasu, S. Yoshifuji, M. Mizuno, M. Hitomi, H. Yamazaki: Int. J. Cast Met. Res. 22 (2009) 374–81.10.1179/174313309X380413 ↗
4. I. Ohnaka, A. Sugiyama, J.D. Zhu, and F. Kinoshita: Model. Cast., Weld. Adv. Solidif. Processes XII, Proc. Int. Conf., 12th, 2009, pp. 403–10.
5. J. Duan, D.M. Maijer, S.L. Cockcroft, C. Reilly, K. Nguyen, and D. Au: Physical and Computational Models of Free Surface Related Defects in Low-Pressure Die-Cast Aluminum Alloy Wheels, 2011, pp. 21–28.10.1002/9781118062050.ch3 ↗
6. H. Zhao, I. Ohnaka, J. Zhu, Appl. Math. Model. 32 (2008) 185–94.10.1016/j.apm.2006.11.009 ↗
7. A. Kimatsuka, I. Ohnaka, J.D. Zhu, T. Ohmichi, Int. J. Cast Met. Res. 15 (2002) 149–52.10.1080/13640461.2003.11819475 ↗
8. J. Jakumeit, K. Goodheart, and M. Albers: Model. Cast., Weld. Adv. Solidif. Processes XII, Proc. Int. Conf., 12th, 2009, pp. 427–34.
9. J. Duan, D.M. Maijer, S.L. Cockcroft, C. Reilly, K. Nguyen, and D. Au: Modeling of Die Filling of Low-Pressure Die-Cast Aluminum Alloy Wheels, 2012, pp. 177–84.10.1002/9781118357002.ch24 ↗
10. K. Li, E. Chang, Acta Mater. 52 (2004) 219–31.10.1016/j.actamat.2003.09.007 ↗
11. D.P.K. Singh, G.D. Mallinson, S.M. Panton, N. Palle, Trans. Am. Foundrymen’s Soc. 107 (1999) 127–33.
12. J. Campbell: Mater. Sci. Technol. 22 (2006) 127–45.10.1179/174328406X74248 ↗
13. D. Su, Y. Zhao, Tezhong Zhuzao Ji Youse Hejin 27 (2007) 682–84.
14. J. Campbell, Castings, 2nd Edition, 2nd Edition ed., Butterworth-Heinemann, Oxford, 2003.
15. L. Yao, S. Cockcroft, D. Maijer, and J. Zhu: Effect of Oxide Films on Microporosity Formation in A356 Aluminum Alloy Castings, 2010.
16. X.G. Chen, R.I.L. Guthrie, and J.E. Gruzleski: Proc. Int. Conf. Molten Alum. Process., 4th, 1995, pp. 15–28.
17. J.A. Taylor, G.B. Schaffer, and D.H. St. John: Proc. Int. Conf. Molten Alum. Process., 4th, 1995, pp. 43–54.
18. A.R. Mirak, M. Divandari, M. Zebardast, and S.M.A. Boutorabi: Nashriyyah-i Danishkadah-i Fanni, 2007, vol. 40, pp. 981–990 (Persian), 4–5 (English).
19. J. Mi, R.A. Harding, M. Wickins, J. Campbell, Intermetallics. 11 (2003) 377–85.10.1016/S0966-9795(03)00006-2 ↗
20. T.W. Clyne, M. Wolf, W. Kurz, Metall. Trans., B. 13B (1982) 259–66.10.1007/BF02664583 ↗
21. M. Rappaz, J.-M. Drezet, M. Gremaud, Metall. Mater. Trans. A. 30A (1999) 449–55.10.1007/s11661-999-0334-z ↗
22. G. Chadha, J.E. Allison, and J.W. Jones: Magnesium Technol. 2004, Proc. Symp., 2004, pp. 181–86.
23. E. Dubensky, D. Koss, Metall. Trans. A, 18A (1987) 1887–95.10.1007/BF02647018 ↗
24. A.E. Miller, D.M. Maijer, Mater. Sci. Eng. A 435A (2006) 100–11.10.1016/j.msea.2006.07.052 ↗
25. A.E. Miller: Investigation of Erosive-Corrosive Wear in the Low Pressure Die Casting of Aluminum A356, 2005.10.1016/j.msea.2006.07.052 ↗
26. J. Duan: Physical and Computational Models of Free Surface Related Defects in Low-Pressure Die-Cast Aluminum Alloy Wheels, 2011.10.1002/9781118062050.ch3 ↗
27. I. ANSYS, ANSYS CFX Release 12.0 Documentation, 2009.
28. L.D. Landau and E.M. Lifshitz: Fluid Mechanics, 2, 2 English, rev ed., Pergamon Press, Oxford, 1987.
29. R.W. Fox, Fox and McDonald’s Introduction to Fluid Mechanics, 8th ed., John Wiley & Sons, Hoboken, NJ, 2011.
30. CRC Handbook of Chemistry and Physics, 91st edn., CRC Press, Cleveland, OH, 2010–2011.
31. J.R. Davis, J.R. Davis & Associates: ASM International. Handbook Committee, Aluminum and Aluminum Alloys, ASM International, Materials Park, OH, 1993.
32. Swift R.E., Jackson J.H., Eastwood L.W: AFS Trans. 93 (1949) 76–88.
33. N.D. Perkins, C.J. Bain, J. Aust. Inst. Met. 10 (1965) 160–68.