journal article·2009-12Open access

Effect of Microstructure on Cavitation during Hot Deformation of a Fine-Grained Aluminum-Magnesium Alloy as Revealed through Three-Dimensional Characterization

Jung-Kuei “Brian” Chang, Eric M. Taleff, Paul E. Krajewski

Abstract

The effect of microstructure on cavitation developed during hot deformation of a fine-grained AA5083 aluminum-magnesium alloy is investigated. Two-point correlation functions and three-dimensional (3-D) microstructure characterization reveal that cavitation depends strongly on the mechanism that controls plastic deformation. Grain-boundary-sliding (GBS) creep produces large, interconnected cavities rapidly during plastic straining. Solute-drag (SD) creep produces isolated cavities with less total volume fraction at a given strain. The 3-D microstructure data reveal adjacency between various microstructural features. Cavities are observed to be preferentially adjacent to large Al6(Mn,Fe) particles and to Mg-Si particles of all observed sizes. These data suggest that cavities preferentially nucleate at Mg-Si particles and at large Al6(Mn,Fe) particles. This result may be applied to reduce cavitation in commercial hot-forming operations utilizing aluminum-magnesium alloys.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. A.J. Barnes: J. Mater. Eng. Perform., 2007, vol. 16, pp. 440–54.10.1007/s11665-007-9076-5 ↗
2. Z. Li and H. Guo: Mater. Sci. Forum, 2005, vols. 475–479, pp. 3037–42.10.4028/www.scientific.net/MSF.475-479.3037 ↗
3. D.G. Sanders: Mater. Sci. Forum, 2001, vols. 357–359, pp. 17–22.10.4028/www.scientific.net/MSF.357-359.17 ↗
4. J.G. Schroth: in Advances in Superplasticity and Superplastic Forming, E.M. Taleff, P.A. Friedman, P.E. Krajewski, R.S. Mishra, and J.G. Schroth, eds., TMS, Warrendale, PA, 2004, pp. 9–20.
5. M.-A. Kulas, W.P. Green, E.M. Taleff, P.E. Krajewski, and T.R. McNelley: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 1249–61.10.1007/s11661-005-0217-x ↗
6. M.-A. Kulas, W.P. Green, E.M. Taleff, P.E. Krajewski, and T.R. McNelley: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 645–55.10.1007/s11661-006-0036-8 ↗
7. M.-A. Kulas, P.E. Krajewski, J.R. Bradley, and E.M. Taleff: J. Mater. Eng. Perform., 2007, vol. 16, pp. 308–13.10.1007/s11665-007-9057-8 ↗
8. A. Ball and M.M. Hutchison: Met. Sci. J., 1969, vol. 3, pp. 1–7.10.1016/0036-9748(69)90167-7 ↗
9. J.S. Vetrano, C.A. Lavender, C.H. Hamilton, M.T. Smith, and S.M. Bruemmer: Scripta Metall. Mater., 1994, vol. 30, pp. 565–70.10.1016/0956-716X(94)90430-8 ↗
10. P.A. Friedman and A.K. Ghosh: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3827–39.10.1007/BF02595632 ↗
11. H. Iwasaki, H. Hosokawa, T. Mori, T. Tagata, and K. Higashi: Mater. Sci. Eng., A, 1998, vol. 252, pp. 199–202.10.1016/S0921-5093(98)00678-9 ↗
12. I.C. Hsiao, J.C. Huang, and S.W. Su: Mater. Trans., JIM, 1999, vol. 40, pp. 744–53.10.2320/matertrans1989.40.744 ↗
13. R.M. Cleveland, A.K. Ghosh, and J.R. Bradley: Mater. Sci. Eng., A, 2003, vol. 351, pp. 228–36.10.1016/S0921-5093(02)00848-1 ↗
14. D. Weinstein: Trans. AIME, 1969, vol. 245, pp. 2041–46.
15. C.W. Humphries and N. Ridley: J. Mater. Sci., 1974, vol. 9, pp. 1429–35.10.1007/BF00552928 ↗
16. N. Ridley and D.W. Livesey: Res Mech. Lett., 1981, vol. 1, pp. 73–77.
17. J.J. Blandin, B. Hong, A. Varloteaux, M. Suery, and G. L’Esperance: Acta Mater., 1996, vol. 44, pp. 2317–26.10.1016/1359-6454(95)00340-1 ↗
18. A.H. Chokshi: Mater. Sci. Eng., A, 2005, vols. 410–411, pp. 95–99.10.1016/j.msea.2005.08.069 ↗
19. M. Mabuchi, Y. Chino, and H. Iwasaki: Mater. Sci. Forum, 2005, vols. 475–479, pp. 2945–48.10.4028/www.scientific.net/MSF.475-479.2945 ↗
20. D.H. Bae and A.K. Ghosh: Acta Mater., 2002, vol. 50, pp. 511–23.10.1016/S1359-6454(01)00375-5 ↗
21. N. Chandra, M.K. Khraisheh, and P. Kalu: Mater. Sci. Forum, 2005, vol. 475–479, pp. 2931–36.10.4028/www.scientific.net/MSF.475-479.2931 ↗
22. C.F. Martin, C. Josserond, L. Salvo, J.J. Blandin, P. Cloetens, and E. Boller: Scripta Mater., 2000, vol. 42, pp. 375–81.10.1016/S1359-6462(99)00355-3 ↗
23. H.Q. Yu, J.J. Blandin, and L. Salvo: Mater. Sci. Forum, 2004, vols. 447–448, pp. 55–60.10.4028/www.scientific.net/MSF.447-448.55 ↗
24. E.M. Taleff, T. Leon-Salamanca, R.A. Ketcham, R. Reyes, and W.D. Carlson: J. Mater. Res., 2000, vol. 15, pp. 76–84.10.1557/JMR.2000.0015 ↗
25. J. Hu, K. Ikeda, and T. Murakami: J. Jpn. Inst. Light Met., 1996, vol. 46, pp. 126–31.10.2464/jilm.46.126 ↗
26. Y.S. Sato, S.H.C. Park, and H. Kokawa: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 3033–42.10.1007/s11661-001-0178-7 ↗
27. D.H. Bae and A.K. Ghosh: Acta Mater., 2002, vol. 50, pp. 993–1009.10.1016/S1359-6454(01)00399-8 ↗
28. C.F. Martin, C. Josserond, L. Salvo, J.J. Blandin, P. Cloetens, and E. Boller: Acta Metall., 2000, vol. 42, pp. 375–81.
29. T.R. McNelley, K. Oh-Ishi, A.P. Zhilyaev, S. Swaminthan, P.E. Krajewski, and E.M. Taleff: Metall. Mater. Trans. A, 2008, vol. 39, pp. 50–64.10.1007/s11661-007-9401-5 ↗
30. ASM Specialty Handbook: Aluminium and Aluminum Alloys, J.R. Davids, ed., ASM International, Materials Park, OH, 1993, pp. 3–5.
31. ANSI H35.1. “American National Standard Alloy and Temper Designation Systems for Aluminum,” American National Standards Institute, Washington, DC, 2004.
32. ASTM E112-96 (2004) e2. “Standard Test Methods for Determining Average Grain Size,” ASTM International, West Conshohocken, PA, 2004.
33. N. Chawla, V.V. Ganesh, and B. Wunsch: Scripta Mater., 2004, vol. 51, pp. 161–65.10.1016/j.scriptamat.2004.03.043 ↗
34. M. Li, S. Ghosh, T.N. Rouns, H. Weiland, O. Richmond, and W. Hunt: Mater. Charact., 1998, vol. 41, pp. 81–95.10.1016/S1044-5803(98)00023-0 ↗
35. M.V. Krala, M.A. Manganb, G. Spanosb, and R.O. Rosenberg: Mater. Charact., 2000, vol. 45, pp. 17–23.10.1016/S1044-5803(00)00046-2 ↗
36. J.C. Fiala: J. Microsc., 2005, vol. 218, pp. 52–61.10.1111/j.1365-2818.2005.01466.x ↗
37. J. Hu, K. Ikeda, and T. Murakami: J. Jpn. Inst. Light Met., 1996, vol. 46, pp. 126–31.10.2464/jilm.46.126 ↗
38. N. Llorca-Isern, C. Luis-Perez, P.A. Gonzalea, L. Laborde, and D. Patino: Rev. Adv. Mater. Sci., 2005, vol. 10, pp. 473–78.
39. M. Czechowski: J. Mater. Process. Technol., 2005, vols. 164–165, pp. 1001–06.10.1016/j.jmatprotec.2005.02.078 ↗
40. S. Kim, M.P. Balogh, and R.A. Waldo: in Advances in Superplasticity and Superplastic Forming, E.M. Taleff, P.A. Friedman, P.E. Krajewski R.S. Mishra, and J.G. Schroth, eds., TMS, Warrendale, PA, 2004, pp. 139–49.
41. G. Lucadamo, N.Y.C. Yang, C. San Marchi, and E.J. Lavernia: Mater. Sci. Eng., A, 2006, vol. 430A, pp. 230–41.10.1016/j.msea.2006.05.039 ↗
42. H. Singh, Y. Mao, A. Sreeranganathan, and A.M. Gokhale: Modell. Simul. Mater. Sci. Eng., 2006, vol. 14, pp. 351–63.10.1088/0965-0393/14/3/002 ↗
43. K. Marthinsen, J.M. Fridy, T.N. Rouns, K.B. Lippert, and E. Nes: Scripta Mater., 1998, vol. 39, pp. 1177–83.10.1016/S1359-6462(98)00315-7 ↗
44. H. Singh, A.M. Gokhale, Y. Mao, and J.E. Spowart: Acta Mater., 2006, vol. 54, pp. 2131–43.10.1016/j.actamat.2005.12.037 ↗
45. A. Tewari, A.M. Gokhale, J.E. Spowart, and D.B. Miracle: Acta Mater., 2004, vol. 52, pp. 307–19.10.1016/j.actamat.2003.09.016 ↗
46. A.D. Rollett, R. Campman, and D. Saylor: Mater. Sci. Forum, 2006, vols. 519–521, pp. 1–10.10.4028/www.scientific.net/MSF.519-521.1 ↗
47. P.A. Friedman and A.K. Ghosh: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3827–39.10.1007/BF02595632 ↗