journal article·2013-05

Ratcheting Behavior of a Titanium-Stabilized Interstitial Free Steel

P. S. De, P. C. Chakraborti, B. Bhattacharya, M. Shome, D. Bhattacharjee

Publisher page

Abstract

Engineering stress-control ratcheting behavior of a titanium-stabilized interstitial free steel has been studied under different combinations of mean stress and stress amplitude at a stress rate of 250 MPa s−1. Tests have been done up to 29.80 pct true ratcheting strain evolution in the specimens at three maximum stress levels. It is observed that this amount of ratcheting strain is more than the uniform tensile strain at a strain rate of 10−3 s−1 and evolves without showing tensile instability of the specimens. In the process of ratcheting strain evolution at constant maximum stresses, the effect of increasing stress amplitude is found to be more than that of increasing the mean stress component. Further, the constant maximum stress ratcheting test results reveal that the number of cycles (N) required for 29.80 pct. true ratcheting strain evolution exponentially increases with increase of stress ratio (R). Post-ratcheting tensile test results showing increase of strength and linear decrease in ductility with increasing R at different constant maximum stresses indicate that stress parameters used during ratcheting tests influence the size of the dislocation cell structure of the steel even with the same amount of ratcheting strain evolution. It is postulated that during ratcheting fatigue, damage becomes greater with the increase of R for any fixed amount of ratcheting strain evolution at constant maximum stress.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (73)

Show source-provided references
1. Z. Xia, D. Kujawski, and F. Ellyin: Int. J. Fatigue, 1996, vol. 18, pp. 335–41.10.1016/0142-1123(96)00088-6 ↗
2. J. Polak: Cyclic Plasticity and Low Cycle Fatigue Life of Metals, Elsevier Science Ltd, Amsterdam, 1991.
3. N.E. Dowling: Mechanical Behavior of Materials, Prentice Hall, Upper Saddle River, New Jersey, 1999.
4. R.J. Rider, S.J. Harvey, H.D. Chandler: Int. J. Fatigue, 1995, vol. 17, pp. 507–11.10.1016/0142-1123(95)00046-V ↗
5. X. Yang: Int. J. Fatigue, 2005, vol. 27, pp. 1124–32.10.1016/j.ijfatigue.2005.01.004 ↗
6. M. Karadag and R.I. Stephens: Int. J. Fatigue, 2003, vol. 25, pp. 191–200.10.1016/S0142-1123(02)00116-0 ↗
7. C. Gupta, J. Chakravartty, G. Reddy and S. Banerjee: Int. J. Press. Vessels Pip., 2005, vol. 82, pp. 459–69.10.1016/j.ijpvp.2005.01.005 ↗
8. S. Kulkarni: Int. J. Press. Vessels Pip., 2003, vol. 80, pp. 179–85.10.1016/S0308-0161(03)00029-2 ↗
9. S. Sinha and S. Ghosh: Int. J. Fatigue, 2006, vol. 28, pp. 1690–1704.10.1016/j.ijfatigue.2006.01.008 ↗
10. C. L. Xie, S. Ghosh and M. Groeber: J. Eng. Mater. Technol., 2004, vol. 126, pp. 339.10.1115/1.1789966 ↗
11. X. Feaugas and C. Gaudin: Int. J. Plast., 2004, vol. 20, pp. 643–62.10.1016/S0749-6419(03)00076-7 ↗
12. C. Gaudin, X. Feaugas: Acta Mater., 2004, vol. 52, pp. 3097–3110.10.1016/j.actamat.2004.03.011 ↗
13. G. Kang, Q. Gao, X. Yang: Mech Mater, 2002, vol. 34, pp. 145–59.10.1016/S0167-6636(01)00099-0 ↗
14. G. Kang, Y. Liu, Z. Li: Mater. Sci. Eng. A, 2006, vol. 435-436, pp. 396–404.10.1016/j.msea.2006.07.006 ↗
15. J.L. Chaboche and D. Nouailhas: J. Eng. Mater. Technol., 1989, vol. 111, pp. 384–92.10.1115/1.3226484 ↗
16. M.B. Ruggles and E. Krempl: J. Eng. Mater. Technol., 1989, vol. 111, pp. 378–83.10.1115/1.3226483 ↗
17. M.B. Ruggles and E. Krempl: J. Mech. Phys. Solids, 1990, vol. 38, pp. 575–85.10.1016/0022-5096(90)90015-V ↗
18. N. Ohno and M. Abdel-Karim: J. Eng. Mater. Technol., 2000, vol. 122, pp. 35–41.10.1115/1.482762 ↗
19. G. Kang and Y. Liu: Mater. Sci. Eng. A, 2008, vol. 472, pp. 258–68.10.1016/j.msea.2007.03.029 ↗
20. G. Kang, Y. Liu, J. Ding and Q. Gao: Int. J. Plast., 2009, vol. 25, pp. 838–60.10.1016/j.ijplas.2008.06.004 ↗
21. L. Kunz and P. Lukas: Mater. Sci. Eng. A, 2001, vol. 319-321, pp. 555–58.10.1016/S0921-5093(01)01094-2 ↗
22. M. Yaguchi and Y. Takahashi: Int. J. Plast., 2005, vol. 21, pp. 43–65.10.1016/j.ijplas.2004.02.001 ↗
23. P.J. Armstrong and C.O. Frederick: Technical Report RD/B/N/731, C.E.G.B, Central Electricity Generating Board, Berkeley, 1966.
24. J.L. Chaboche: Int. J. Plast., 1991, vol. 7, pp. 661–78.10.1016/0749-6419(91)90050-9 ↗
25. J.L. Chaboche: Eur. J. Mech. A. Solids, 1994, vol. 13, pp. 501–18.
26. N. Ohno and J.D. Wang: Int. J. Plast., 1993, vol. 9, pp. 375–89.10.1016/0749-6419(93)90042-O ↗
27. N. Ohno and J.D. Wang: Int. J. Plast., 1993, vol. 9, pp. 390–403.
28. N. Ohno and J.D. Wang: Eur. J. Mech. A. Solids, 1994, vol. 13, pp. 519–31.
29. Y. Jiang and H. Sehitoglu: Int. J. Plast., 1994, vol. 10, pp. 579–608.10.1016/0749-6419(94)90015-9 ↗
30. Y. Jiang and H. Sehitoglu: J. Eng. Mater. Technol., 1996, vol. 63, pp. 720–33.
31. Y. Jiang and P. Kurath: Int. J. Plast., 1996, vol. 12, pp. 387–415.10.1016/S0749-6419(96)00013-7 ↗
32. M. Abdel-Karim and N. Ohno: Int. J. Plast., 2000, vol. 16, pp. 225–40.10.1016/S0749-6419(99)00052-2 ↗
33. G.Z. Kang, Q. Gao and X.J. Yang: Int. J. Non Linear Mech., 2004, vol. 39, pp. 843–57.10.1016/S0020-7462(03)00060-X ↗
34. G.Z. Kang and Q. Gao: Mech. Mater., 2002, vol. 34, pp. 809–20.10.1016/S0167-6636(02)00198-9 ↗
35. G.Z. Kang: Mech. Mater., 2004, vol. 36, pp. 299–312.10.1016/S0167-6636(03)00024-3 ↗
36. X. Chen and R. Jiao: Int. J. Plast., 2004, vol. 20, pp. 871–98.10.1016/j.ijplas.2003.05.005 ↗
37. X. Chen, R. Jiao and K.S. Kim: Int. J. Plast., 2005, vol. 21, pp. 161–84.10.1016/j.ijplas.2004.05.005 ↗
38. T. Hassan and S. Kyriakides: Int. J. Plast., 1992, vol. 8, pp. 91–116.10.1016/0749-6419(92)90040-J ↗
39. T. Hassan, E. Corona and S. Kyriakides: Int. J. Plast., 1992, vol. 8, pp. 117–46.10.1016/0749-6419(92)90010-A ↗
40. G. Chen, X. Chen and C. Niu: Mater. Sci. Eng. A, 2006, vol. 421, pp. 238–44.10.1016/j.msea.2006.01.052 ↗
41. S.J. Park, K.S. Kim and H.S. Kim: Fatigue Fract. Eng. Mater. Struct., 2007, vol. 30, pp. 1076–83.10.1111/j.1460-2695.2007.01177.x ↗
42. S.K. Paul, S. Sivaprasad, S. Dhar and S. Tarafder: Mater. Sci. Eng. A, 2011, vol. 528, pp. 4873–82.10.1016/j.msea.2011.03.048 ↗
43. S.K. Paul, S. Sivaprasad, S. Dhar and S. Tarafder: Int. J. Press. Vessels Pip., 2010, vol. 87, pp. 440–46.10.1016/j.ijpvp.2010.07.008 ↗
44. H. Mughrabi and H.J. Christ: ISIJ Int., 1997, vol. 37, pp. 1154–69.10.2355/isijinternational.37.1154 ↗
45. N. Narasaiah, P.C. Chakraborti, R. Maity and K.K. Ray: ISIJ Int., 2005, vol. 45, pp. 127–32.10.2355/isijinternational.45.127 ↗
46. S. Majumdar, D. Bhattacharjee and K.K. Ray: Metall. Mater. Trans. A, 2008, vol. 39A, pp 1676–90.10.1007/s11661-008-9537-y ↗
47. S. Majumdar, D. Bhattacharjee and K.K. Ray: Scripta Mater., 2011, vol. 64, pp. 288–91.10.1016/j.scriptamat.2010.10.001 ↗
48. M.T. Milan, D. Spinelli and W.W.B. Filho: Int. J. Fatigue, 2001, vol. 23, pp. 129–33.10.1016/S0142-1123(00)00076-1 ↗
49. C.-C. Shih, N.-J. Ho and H.-L. Huang: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 1995–2001.10.1007/s11661-010-0186-6 ↗
50. M.A. Islam and Y. Tomota: Adv. Mater. Res., 2007, vol. 15-17, pp. 804–09.10.4028/www.scientific.net/AMR.15-17.804 ↗
51. M.N. James: Eng. Fract. Mech., 2010, vol. 77, pp. 1998–2007.10.1016/j.engfracmech.2009.12.006 ↗
52. M.A. Islam and Y. Tomota: Int. J. Mater. Res., 2006, vol. 97, pp. 1559–65.10.1515/ijmr-2006-0243 ↗
53. A. Daniélou, J. Rivat, M. Robillard, J. Stolarz and T. Magnin: Mater. Sci. Eng. A, 2001, vol. 319-321, pp. 550–5410.1016/S0921-5093(01)01090-5 ↗
54. Surajit Kumar Paul: Mater. Sci. Eng., A, 2012, vol. 538, pp. 349–55.10.1016/j.msea.2012.01.058 ↗
55. F. Lorenzo and C. Laird: Acta Metall., 1984, vol. 32, pp. 681–92.10.1016/0001-6160(84)90142-1 ↗
56. M. Caul and V. Randle : Mater. Char., 1997, vol. 38, pp. 155–63.10.1016/S1044-5803(97)00038-7 ↗
57. M Caul, V Randle and L Burrows: Ironmaking Steelmaking, 1997, vol. 24, pp. 368–72.
58. S. Sivaprasad, S.K. Paul, S. K. Gupta, V. Bhasin, N. Narasaiah, S. Tarafder: Int. J. Press. Vessels Pip., 2010, vol. 87, pp. 464–69.10.1016/j.ijpvp.2010.06.002 ↗
59. F. Lorenzo and C. Laird: Acta Metall., 1984, vol. 32, pp. 671–80.10.1016/0001-6160(84)90141-X ↗
60. H.D. Chandler and J.V. Bee: Acta Metall., 1985, vol. 33, pp. 1121–27.10.1016/0001-6160(85)90206-8 ↗
61. C.E. Feltner: Acta Metall., 1963, vol. 11, pp. 817––28.10.1016/0001-6160(63)90021-X ↗
62. G. Kang, Y. Dong, H. Wang, Y. Liu, and X. Cheng: Mater. Sci. Eng. A, 2010, vol. 527, pp. 5952–61.10.1016/j.msea.2010.06.020 ↗
63. S.I. Hong and C. Laird: Mater. Sci. Eng. A, 1990, vol. 124, pp. 183–201.10.1016/0921-5093(90)90148-V ↗
64. S.I. Hong and C. Laird: Mater. Sci. Eng. A, 1990, vol. 128, pp. 155–69.10.1016/0921-5093(90)90224-Q ↗
65. V. Kliman and M. Bily: Mater. Sci. Eng., 1980, vol. 44, pp. 73–79.10.1016/0025-5416(80)90232-3 ↗
66. S.K. Paul, S. Sivaprasad, S. Dhar and S. Tarafder: J. Nucl. Mater., 2010, vol. 401, pp. 17–24.10.1016/j.jnucmat.2010.03.014 ↗
67. A.P.L. Turner and T.J. Martin: Metall. Trans. A, 1980, vol. 11A, pp. 475–81.10.1007/BF02654571 ↗
68. F. Lorenzo and C. Laird: Mater. Sci. Eng., 1984, vol. 62, pp. 205–10.10.1016/0025-5416(84)90223-4 ↗
69. R. Eckert, C. Laird and J. Bassani: Mater. Sci. Eng., 1987, vol. 91, pp. 81–88.10.1016/0025-5416(87)90285-0 ↗
70. P. Lukas and L. Kunz: Int. J. Fatigue, 1989, vol. 11, pp. 55–58.10.1016/0142-1123(89)90048-0 ↗
71. C. Holste, W. Kleinert, R. Gurth and K. Mecke: Mater. Sci. Eng. A, 1994, vol. 187, pp. 113–23.10.1016/0921-5093(94)90338-7 ↗
72. C. Lim, K. Kim and J. Seong: Int. J. Fatigue, 2009, vol. 31, pp. 501–07.10.1016/j.ijfatigue.2008.04.008 ↗
73. K. Dutta, S. Sivaprasad, S. Tarafder and K.K. Ray: Mater. Sci. Eng. A, 2010, vol. 527, pp. 7571–79.10.1016/j.msea.2010.07.107 ↗