journal article·2021-08

Effect of Heat Treatment on the Microstructural Evolution and Properties of 3D-Printed and Conventionally Produced Medical-Grade Ti6Al4V ELI Alloy

Niyousha Azgomi, Francis Tetteh, Solomon Hanson Duntu, Solomon Boakye-Yiadom

Publisher page

Abstract

Medical-grade Ti6Al4V extra-low interstitial (ELI) alloy has widespread applications in the biomedical industry due to its excellent corrosion and wear resistance. Even though 3D printing offers geometry flexibility and rapid means of fabricating customized parts, 3D-printed parts are often plagued with defects including porosity, high residual stresses, and non-equilibrium structures. Thus, post-processing heat treatments may be required to optimize its properties for engineering applications. In this study, the effect of post-processing heat treatment on the microstructure, hardness, and wear properties of 3D-printed and conventionally produced medical-grade Ti6Al4V ELI alloy samples was investigated. In general, distinct α (alpha) lath and basket-weave lath structures with a high degree of orientation were observed within the microstructure of the as-printed samples. Heat treatment led to the growth of distinct continuous and discontinuous α-lath structures along prior β (beta) grain boundaries as well as basket-weave lath and the coalescence of V-shaped structures within the prior β-grains. The hardness of both the 3D-printed and conventionally produced samples increased after heat treatment (≥ 400 HV), regardless of the cooling rate and aging temperature. After being water quenched/aged, the 3D-printed samples at 500 °C had the highest hardness values owing to the presence of coarse V-shaped structures. Furthermore, the V-shaped structures were always harder than all other structures regardless of the heat treatment and manufacturing process used, indicating that these structures dictate the overall mechanical integrity of the material. X-ray diffraction and electron probe microanalysis indicated that the V-shaped structures are rich in aluminum and titanium content, which can form hcp α′ (AlTi3) intermetallic phases. The 3D-printed samples had higher wear resistance overall than the conventionally produced samples regardless of the heat treatment used. Aging at 500 °C led to a higher coefficient of friction after 3D printing owing to an increase in α-phases. Therefore, during heat treatment, the microstructure and properties of medical-grade Ti6Al4V ELI alloy are significantly affected by the starting microstructure, the rate of cooling below the β-transus, and aging temperature and time, regardless of the manufacturing process used.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Titanium Alloys Microstructure and Properties · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. LW Meyer L Krüger K Sommer T Halle M Hockauf 2008 Mech. Time Depend. Mater. 12 237 24710.1007/s11043-008-9060-y ↗
2. MT Jovanović S Tadić S Zec Z Mišković I Bobić 2006 Mater. Des. 27 192 19910.1016/j.matdes.2004.10.017 ↗
3. MJ Bermingham SD McDonald MS Dargusch DH Stjohn 2010 Mater. Sci. Forum 654–656 1472 147510.4028/www.scientific.net/MSF.654-656.1472 ↗
4. LW Tsay CY Tsay 1997 Int. J. Fatigue 19 713 72010.1016/S0142-1123(97)00113-8 ↗
5. FJ Gil MP Ginebra JM Manero JA Planell 2001 J. Alloys Compd. 329 142 15210.1016/S0925-8388(01)01571-7 ↗
6. PN Poondle 2009 T S, Srivatsan and A Patnail J. Alloys Compd. 486 162 16710.1016/j.jallcom.2009.06.172 ↗
7. R Huang M Riddle D Graziano J Warren S Das S Nimbalkar J Cresko E Masanet 2016 J. Clean. Prod. 135 1559 157010.1016/j.jclepro.2015.04.109 ↗
8. G Lutjering JC Williams 2007 Titanium 2 Springer Berlin 6221
9. S Liu YC Shin 2019 Mater. Des. 164 10755210.1016/j.matdes.2018.107552 ↗
10. WW Wits JRR García JMJ Becker 2016 Procedia CIRP 40 693 69810.1016/j.procir.2016.01.156 ↗
11. AM Platform: Additive Manufacturing: Strategic research Agenda, 2014.
12. S Ford M Despeisse 2016 J. Clean. Prod. 137 1573 158710.1016/j.jclepro.2016.04.150 ↗
13. GF Sun XT Shen ZD Wang MJ Zhan S Yao R Zhou ZH Ni 2019 Opt. Laser Technol. 109 71 8310.1016/j.optlastec.2018.07.051 ↗
14. ASTM International 2012 ASTM F2792-12a, Standard Terminology for Additive Manufacturing Technologies ASTM International West Conshohocken, PA
15. International Organization for Standardization: ISO/ASTM 52900:2015—Additive Manufacturing—General Principles—Terminology, International Organization for Standardization, 2015.
16. YC Shin N Bailey C Katinas W Tan 2018 Comput. Mech. 61 617 63610.1007/s00466-018-1545-1 ↗
17. M Zenou L Grainger 2018 Additive Manufacturing Elsevier Amsterdam 53 10310.1016/B978-0-12-812155-9.00003-7 ↗
18. A Iveković N Omidvari B Vrancken K Lietaert L Thijs K Vanmeensel J Vleugels JP Kruth 2017 Int. J. Refract. Met. Hard Mater. 72 27 3210.1016/j.ijrmhm.2017.12.005 ↗
19. T Vilaro C Colin JD Bartout 2011 Metall. Mater. Trans. A 42A 3190 319910.1007/s11661-011-0731-y ↗
20. LE Murr SA Quninones SM Gaytan MI Lopez A Rodela EY Martinez DH Hernandez E Martinez F Medina RB Wicker 2009 J. Mech. Behav. Biomed. Mater. 2 20 3210.1016/j.jmbbm.2008.05.004 ↗
21. L Facchini E Magalini P Robotti A Molinari S Höges K Wissenbach 2010 Rapid Prototyp. J. 16 450 45910.1108/13552541011083371 ↗
22. L Facchini E Magalini P Robotti A Molinari 2009 Rapid Prototyp. J. 15 171 17810.1108/13552540910960262 ↗
23. L Thijs F Verhaeghe T Craeghs J Humbeeck Van JP Kruth 2010 Acta Mater. 58 3303 331210.1016/j.actamat.2010.02.004 ↗
24. E Chlebus B Kuźnicka T Kurzynowski B Dybała 2011 Mater. Charact. 62 488 49510.1016/j.matchar.2011.03.006 ↗
25. YL Hao SJ Li R Yang 2016 Rare Met. 37 191 201
26. L Ciocca M Fantini F Crescenzio De G Corinaldesi R Scotti 2011 Med. Biol. Eng. Comput. 49 1347 135210.1007/s11517-011-0813-4 ↗
27. L Parry IA Ashcroft RD Wildman 2016 Addit. Manuf. 12 1 15
28. S Tammas-Williams H Zhao F Léonard F Derguti I Todd PB Prangnell 2015 Mater. Charact. 102 47 6110.1016/j.matchar.2015.02.008 ↗
29. PH Li WG Guo WD Huang Y Su X Lin KB Yuan 2015 Mater. Sci. Eng. A 647 32 3410.1016/j.msea.2015.07.028 ↗
30. H Galarraga DA Lados RR Dehoff MM Kirka P Nandwana 2016 Addit. Manuf. 10 47 57
31. M Peter K Jean-Pierre 2006 Rapid Prototyp. J. 12 254 26510.1108/13552540610707013 ↗
32. M Yan P Yu 2015 Sintering Techniques of Materials InTech London
33. GA Longhitano MA Arenas A Conde MA Larosa AL Jardini CAC Zavaglia JJ Damborenea 2018 J. Alloys Compd. 765 961 96810.1016/j.jallcom.2018.06.319 ↗
34. SA Bello I Jesús-Maldonado De E Rosim-Fachini PA Sundaram N Diffoot-Carlo 2010 J. Mater. Sci. Mater. Med. 21 1739 175010.1007/s10856-010-4016-6 ↗
35. H Galarraga RJ Warren DA Lados RR Dehoff MM Kirka P Nandwana 2017 Mater. Sci. Eng. A 685 417 42810.1016/j.msea.2017.01.019 ↗
36. T Ahmed HJ Rack 1998 Mater. Sci. Eng. A 243 206 21110.1016/S0921-5093(97)00802-2 ↗
37. JV Vaerenbergh 2008 Process Optimization in Selective Laser Melting University of Twente Twente
38. B Vandenbroucke 2008 Selective Laser Melting of Biocompatible Metals for Rapid Manufacturing of Medical Parts KU Leuven Leuven
39. R Petzold HF Zeilhofer WA Kalender 1999 Comput. Med. Imaging Graph. 23 277 28410.1016/S0895-6111(99)00025-7 ↗
40. H Liang D Xie Y Mao J Shi C Wang L Shen Z Tian 2019 Metals (Basel) 9 41610.3390/met9040416 ↗
41. G Lütjering JC Williams 2003 Titanium Springer Berlin10.1007/978-3-540-71398-2 ↗
42. KG Budinski 1991 Wear 151 203 21710.1016/0043-1648(91)90249-T ↗
43. WQ Toh P Wang X Tan MLS Nai E Liu SB Tor 2016 Metals (Basel) 6 9 1310.3390/met6110284 ↗
44. JK Ervin 2008 Post Heat Treatment of Ti6AL4V Produced via Solid Freeform Electron Beam Melting North Carolina State University Raleigh
45. W Sha Z Guo 1999 J. Alloys Compd. 290 4 810.1016/S0925-8388(99)00199-1 ↗
46. B Vrancken L Thijs JP Kruth J Humbeeck Van 2012 J. Alloys Compd. 541 177 18510.1016/j.jallcom.2012.07.022 ↗
47. S Malinov W Sha Z Guo CC Tang AE Long 2002 Mater. Charact. 48 279 29510.1016/S1044-5803(02)00286-3 ↗
48. Y. Fan, W. Tian, Y. Guo, Z. Sun, and J. Xu: Adv. Mater. Sci. Eng., 2016, 1687-8434.10.1155/2016/7278267 ↗
49. MJ Donachie 2000 Titanium: A Technical Guide ASM International Materials Park10.31399/asm.tb.ttg2.9781627082693 ↗
50. R. Pederson: Microstructure and Phase Transformation of Ti–6Al–4V. Thesis, 2002.
51. R Sahoo S Mantry TK Sahoo S Mishra BB Jha 2013 Tribol. Trans. 56 555 56010.1080/10402004.2013.767400 ↗
52. M Emiliani R Brown 1984 Wear 94 323 33810.1016/0043-1648(84)90134-0 ↗
53. M Naim S Bahadur 1986 Wear 112 217 23410.1016/0043-1648(86)90242-5 ↗
54. M Naim S Bahadur 1988 Wear 128 239 24710.1016/0043-1648(88)90061-0 ↗
55. L Ambrosini S Bahadur 1987 Wear 117 37 4810.1016/0043-1648(87)90243-2 ↗
56. I Cvijović-Alagić S Mitrović Z Cvijović D Veljović M Babić M Rakin 2009 Tribol. Ind. 31 17 22