journal article·2018-07

Production and Characterization of WC-Reinforced Co-Based Superalloy Matrix Composites

Özgür Özgün, İlyas Dinler

Publisher page

Abstract

Cobalt-based superalloy matrix composite materials were produced through the powder metallurgy technique using element powders at high purity and nano-sized wolfram carbide (WC) reinforcement in this study. An alloy that had the same chemical composition as the Stellite 6 alloy but not containing carbon was selected as the matrix alloy. The powder mixtures obtained as a result of mixing WC reinforcing member and element powders at the determined ratio were shaped by applying 300 MPa of pressure. The green components were sintered under argon atmosphere at 1240 °C for 120 minutes. The densities of the sintered components were determined by the Archimedes’ principle. Microstructural characterization was performed via X-ray diffraction analysis, scanning electron microscope examinations, and energy-dispersive spectrometry. Hardness measurements and tensile tests were performed for determining mechanical characteristics. The relative density values of the sintered components increased by increasing the WC reinforcement ratio and they could almost reach the theoretical density. It was determined from the microstructural examinations that the composite materials consisted of fine and equiaxed grains and coarse carbides demonstrating a homogeneous dispersion along the microstructure at the grain boundaries. As it was the case in the density values, the hardness and strength values of the composites increased by increasing the WC ratio.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. C.T. Sıms, N.S. Stoloff and W.C. Hagel: Superalloys II, Wiley-Interscience, New York, 1987.
2. U. Malayoglu and A. Neville: Wear, 2003, vol. 255, pp. 181–194.10.1016/S0043-1648(03)00287-4 ↗
3. Khoddamzadeh, R. Liu, M. Liang and Q. Yang: Mater. Design, 2014, vol. 56, pp. 487–494.10.1016/j.matdes.2013.11.034 ↗
4. A. Khoddamzadeh, R. Liu, M. Liang and Q. Yang: Compos. Part A 2012, vol. 43, pp. 344–352.10.1016/j.compositesa.2011.11.023 ↗
5. V. Kuzucu, M. Ceylan, H. Celik and I. Aksoy: J. Mater. Process. Technol., 1998, vol. 79, pp. 47–51.10.1016/S0924-0136(97)00452-4 ↗
6. R. Ahmed, H.D.V. Lovelock, N.H. Faisal and S. Davies: Tribol. Int., 2014, vol. 80, pp. 98–114.10.1016/j.triboint.2014.06.015 ↗
7. N.S. Mcintyre, D. Zetaruk and E.V. Murphy: J. Electrochem. Soc., 1979, vol. 126, pp. 750–760.10.1149/1.2129132 ↗
8. F. Rosalbino and G. Scavino: Electrochim. Acta, 2013, vol. 111, pp. 656–662.10.1016/j.electacta.2013.08.019 ↗
9. R. Ahmed, A. Ashraf, M. Elameen, N.H. Faisal, A.M. El-Sherik, Y.O. Elakwah and M.F.A. Goosen: Wear, 2014, vol. 312, pp. 70-82.10.1016/j.wear.2014.02.006 ↗
10. H.Ö. Gülsoy, Ö. Özgün and S. Bilketay: Mater. Sci. Eng. A, 2016, vol. 651, pp. 914-924.10.1016/j.msea.2015.11.058 ↗
11. V. Kuzucu, M. Ceylan, H. Çelik and I. Aksoy: J. Mater. Process. Tech., 1997, vol. 69, pp. 257–263.10.1016/S0924-0136(97)00027-7 ↗
12. L. Wang and D.Y. Li: Wear, 2003, vol. 255 (1-6), pp. 535-544.10.1016/S0043-1648(03)00057-7 ↗
13. J. Shin, J. Doh, J. Yoon, D. Lee and J. Kim: Surf. Coat. Technol., 2003, vol. 166, pp. 117–126.10.1016/S0257-8972(02)00853-8 ↗
14. M.J. Donachie and S.J. Donachie: Superalloys: A technical guide, ASM International, Materials Park, 2002.10.31399/asm.tb.stg2.9781627082679 ↗
15. P. Waldner, E. Knigsberger and H. Gamsjfiger: J. Alloy. Compd., 1995, vol. 220, pp. 148–151.10.1016/0925-8388(94)06016-9 ↗
16. D. Lou, J. Hellman and J. Limatainen: Mater. Sci. Eng. A, 2003, vol. 340, pp. 155–162.10.1016/S0921-5093(02)00173-9 ↗
17. W.H. Jiang, X.D. Yao, H.R. Guan and Z.Q. Hu: J. Mater. Sci., 1999, vol. 34, pp. 2859–2864.10.1023/A:1004683301816 ↗
18. R. Liu, M.X. Yao and X.J. Wu: J. Eng. Mater. Technol., 2004, vol. 126, pp. 204–212.10.1115/1.1651096 ↗
19. R.C. Gassmann: Mater. Sci. Tech., 1996, vol. 12, pp. 691-696.10.1179/026708396790122459 ↗
20. B. Mill: J. Mater. Proc. Tech., 1996, vol. 56, pp. 16-2310.1016/0924-0136(95)01816-6 ↗
21. C.D. Opris, R. Liu, M.X. Yao and X.J. Wu: Mater. Design, 2007, vol. 28, pp. 581–591.10.1016/j.matdes.2005.08.004 ↗
22. Y. Zhan and G. Zhang: Mater. Lett., 2003, vol. 57 (29), pp. 4583–4591.10.1016/S0167-577X(03)00365-3 ↗
23. K.S. Foo, W.M. Banks and A.J. Craven: Composites, 1994, vol. 25 (7), pp. 677-683.10.1016/0010-4361(94)90201-1 ↗
24. V.T. Pham, H.T. Bui, B.T. Tran, V.T. Nguyen, D.Q. Le, X.T. Than, V.C. Nguyen, D.P. Doan and N.M. Phan: Adv. Nat. Sci: Nanosci. Nanotechnol., 2011, vol. 2 (1), pp. 1-4.
25. S.M. Uddin, T. Mahmud, C. Wolf, C. Glanz, I. Kolaric, C. Volkmer, H. Höller, U. Wienecke, S. Roth and H-J. Fecht: Compos. Sci. Technol., 2010, vol. 70 (16), pp. 2253–2257.10.1016/j.compscitech.2010.07.012 ↗
26. G.C. Efe, T. Yener, I. Altinsoy, M. Ipek, S. Zeytin and C. Bindal: J. Alloy. Compd., 2011, vol. 509, pp. 6036-6042.10.1016/j.jallcom.2011.02.170 ↗
27. Y. Ning, P.C. Patnaik, R. Liu, M.X. Yao and X.J. Wu: Mater. Sci. Eng. A, 2005, vol. 391, pp. 313–324.10.1016/j.msea.2004.08.083 ↗
28. T.P.D. Rajan, R.M. Pillai and B.C. Pai: J. Mater. Sci., 1998, vol. 33 (14), pp. 3491-3503.10.1023/A:1004674822751 ↗
29. Ö. Özgün, H.Ö. Gülsoy, F. Findik and R. Yilmaz: Powder Metall., 2012, vol. 55, pp. 405–414.10.1179/1743290112Y.0000000010 ↗
30. Ö. Özgün, H.Ö. Gülsoy, R. Yilmaz and F. Findik: J. Alloy. Comp., 2013, vol. 546, pp. 192–207.10.1016/j.jallcom.2012.08.069 ↗
31. Sh. Zangeneh and H. Farhangi: Mater. Design, 2010, vol. 31, pp. 3504–3511.10.1016/j.matdes.2010.02.021 ↗
32. J.V. Giacchi, C.N. Morando, O. Fornaro and H.A. Palacio, Mater. Charact., 2011, vol. 62, pp. 53–61.10.1016/j.matchar.2010.10.011 ↗
33. G.L. Erickson: Polycrystalline cast superalloys, in: ASM Handbook: Properties and Selection: Irons, Steels, and High Performance Alloys. 2005, vol. 1, pp. 1528–50.
34. A. Parasiris and K.T. Hartwig: Int. J. Ref. Met. H. Mater., 2000, vol. 18, pp. 23-31.10.1016/S0263-4368(00)00005-6 ↗
35. Mccandlish, LE (1996) Met. Powder Rep 51(4):16–2010.1016/S0026-0657(99)80792-9 ↗
36. I Azcona, A Ordóñez, JM Sánchez, F Castro (2002) J. Mater. Sci. 37:4189–95.10.1023/A:1020048105585 ↗
37. B. Wittmann, W-D. Schubert and B. Lux: Int. J. Refract. Met. Hard Mater., 2002, vol. 20, pp. 51–60.10.1016/S0263-4368(01)00070-1 ↗
38. X. Wang, Z.Z. Fang and H.Y. Sohn: Int. J. Refract. Met. Hard Mater., 2008, vol. 26, pp. 232–241.10.1016/j.ijrmhm.2007.04.006 ↗
39. J.R. Fincke, W.D. Swank, and D.C. Haggard: Proc. 7th Nat. Thermal Spray Conf., 1994, ASM International, Boston, pp. 325–30.
40. R.J. Mitchell, C.M.F. Rae and S. Tin: Mater. Sci. Technol., 2005, vol. 21, pp. 125–132.10.1179/174328405X16261 ↗
41. Tu D, Chang S., Chao C, Lin C (1985) J. Vac. Sci. Technol. A vol. 3(6), 2479–82.10.1116/1.572862 ↗
42. H.S. Lee, D.S. Kim, K.B. Yoo and K.S. Song: Met. Mater. Int., 2012, vol. 18 (2), pp. 287–293.10.1007/s12540-012-2012-8 ↗
43. N.S. Stoloff, Wrought and powder metallurgy (P/M) superalloys, in: ASM Handbook: Properties and Selection: Irons, Steels, and High Performance Alloys, vol. 1, 2005, pp. 1478–1527.
44. P. Crook: Cobalt and Cobalt Alloys, in: ASM Handbook: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, vol. 2, 1990, pp. 1404–24.10.31399/asm.hb.v02.a0001073 ↗
45. H. Yu, R. Ahmed, H.D.V. Lovelock and S. Davies: J. Tribol., 2009, vol. 131, pp. 1–12.10.1115/1.2991122 ↗
46. W.S. da Silva, R.M. Souza, J.D.B. Mello and H. Goldenstein: Wear, 2011, vol. 271, pp. 1819–1827.10.1016/j.wear.2011.02.030 ↗
47. Ö. Özgün, R. Yılmaz, H.Ö. Gülsoy and F. Findik: Mater. Charact., 2015, vol. 108, pp. 8–15.10.1016/j.matchar.2015.08.006 ↗