Differential Scanning Calorimetry (DSC) and Thermodynamic Prediction of Liquid Fraction vs Temperature for Two High-Performance Alloys for Semi-Solid Processing (Al-Si-Cu-Mg (319s) and Al-Cu-Ag (201))
Source abstract
Abstract
Abstract There is a need to extend the application of semi-solid processing (SSP) to higher performance alloys such as 319s (Al-Si-Cu-Mg) and 201 (Al-Cu-Ag). The melting of these two alloys was investigated using differential scanning calorimetry (DSC) and thermodynamic prediction. The alloys had been processed by magneto-hydrodynamic (MHD) stirring before receipt to produce a microstructure suitable for SSP. The DSC results for the as-received MHD material were compared with those for material which has been taken through a complete DSC cycle and then reheated for a second DSC run. The effects of microsegregation were then analyzed. A higher liquid fraction for a particular temperature is found in the second DSC run than the first. Microstructural observations suggest this is because the intermetallics which form during the first cooling cycle tend to co-located. Quaternary and ternary reactions then occur during the second DSC heat and the co-location leads to enhanced peaks. The calculated liquid fraction is lower with 10 K/min DSC heating rate comparing with 3 K/min at a given temperature. The DSC scan rate must therefore be carefully considered if it is to be used to identify temperature parameters or the suitability of alloys for SSP. In addition, the starting material for DSC must represent the starting material for the SSP. With thermodynamic prediction, the equilibrium condition will provide better guidance for the thixoforming of MHD stirred starting material than the Scheil condition. The Scheil mode approximates more closely with a strongly microsegregated state.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Solidification and crystal growth phenomena · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. H.V. Atkinson: Mater. Sci. Technol., 2010, vol. 26, pp. 1401–1413.10.1179/026708310X12815992418012 ↗
2. I Polmear, Light alloys: from traditional alloys to nanocrystals, 4th ed., Butterworth-Heinemann, Oxford 2005, pp. 205-23510.1016/B978-075066371-7/50008-6 ↗
3. G. Wallace, A.P. Jackson, S.P. Midson and Q.Zhu: Trans. Nonferrous Mater. Soc. of China, 2010, vol. 20, pp. 1786-1791.10.1016/S1003-6326(09)60375-7 ↗
4. D.Liu, H.V. Atkinson, P. Kapranos and H. Jones: J. Mater. Sci., 2004, vol. 39, pp. 99-105.10.1023/B:JMSC.0000007732.04363.81 ↗
5. Bäckerud L, Chai G, Tamminen J (1990) Solidification characteristics of aluminium alloys: foundry alloys. American Foundrymen’s Society, Inc., Schaumburg
6. F.H. Samuel, A.M. Samuel and H.W. Doty, AFS Trans., 1996, vol. 104, pp. 893–901.
7. E.J. Martinez D., M.A. Cisneros G., S. Valtierra and J. Lacaze, Scripta Mater., 2005, vol. 52, pp. 439-443.10.1016/j.scriptamat.2004.11.012 ↗
8. A.A. Kazakov: Adv. Mater. Processes, 2000, vol. 157, pp. 31-34.
9. Y. Q. Liu, A. Das and Z. Fan: Mater. Sci. Technol., 2004, vol. 20, pp. 35-41.10.1179/026708304225011973 ↗
10. D. Liu, H.V. Atkinson and H. Jones: Acta Mater., 2005, vol. 53, pp. 3807-3819.10.1016/j.actamat.2005.04.028 ↗
11. L. Lasa and J. M. Rodriguez-Ibabe: Mater. Charact., 2002, vol. 48, pp. 371-378.10.1016/S1044-5803(02)00283-8 ↗
12. F.H. Samuel: J. Mater. Res., 1998, vol. 33, pp. 2283-2297.
13. G. Wang, X. Bian, W. Wang and J. Zhang: Mater. Lett., 2003, vol. 57, pp. 4083-4087.10.1016/S0167-577X(03)00270-2 ↗
14. Z. Li, A.M. Samuel, F.H. Samuel, C. Ravindran and S. Valtierra, J. Mater. Sci., 2003, vol. 38, pp. 1203-1218.10.1023/A:1022857703995 ↗
15. S. Nafisi, D. Emadi and R. Ghomashchi, Mater. Sci. Eng., A, 2009, vol. 507, pp. 87-92.10.1016/j.msea.2008.11.052 ↗
16. Y. Birol: J. Alloys Compd., 2009, vol. 486, pp. 173-177.10.1016/j.jallcom.2009.06.165 ↗
17. M.A.M. Arif, M.Z. Omar, N. Muhamad, J. Syarif and P. Kapranos: J. Mater. Sci. & Tech., 2013, vol. 29, pp. 765-74.
18. G.L. Brollo, C.T.W. Proni and L.C. de Paula: Thermochimica Acta, 2017, vol. 651, pp. 22-33.10.1016/j.tca.2017.02.010 ↗
19. D. Zhang, H.V. Atkinson, H.B. Dong and Q. Zhu: Solid State Phenom., 2015, vol. 217-218, pp, 442-449.
20. G. Gottardi, A. Pola, and G.M. La Vecchia: La Metallurgia Italiana, 2015, vol. 5, pp. 11-16.
21. A. Lombardi, A. Elsayed, D. Sediako and C. Ravindran: J. Alloys Compd., 2017, vol. 695, pp. 2628-2636.10.1016/j.jallcom.2016.11.175 ↗
22. Kaufman JG, Rooy EL (2004) Aluminum Alloy Castings: Properties, Processes, and Applications. ASM International, Ohio.10.31399/asm.tb.aacppa.9781627083355 ↗
23. D. Larouche, C. Laroche and M. Bouchard: Acta Mater., 2003 vol. 51, pp. 2161-2170.10.1016/S1359-6454(03)00003-X ↗
24. H.B. Dong, M.R.M. Shin, E.C. Kurum, H. Cama and J.D. Hunt: Fluid phase equilib., 2003, vol. 212, pp. 199-208.10.1016/S0378-3812(03)00257-7 ↗
25. Information on http://www.thermocalc.com/products-services/databases/thermodynamic
26. M.C. Flemings: Metall. Trans., 1974, vol. 5, pp. 2121-2134.10.1007/BF02643923 ↗
27. A. Samuel, J. Gauthier and F. Samuel: Metall. Mater. Trans. A, 1996, vol. 27, pp. 1785-1798.10.1007/BF02651928 ↗
28. Höhne G, Hemminger WF, Flammersheim HJ (2003) Differential scanning calorimetry, 2nd ed., Springer, New York10.1007/978-3-662-06710-9 ↗