journal article·2016-04

Evolution of Microstructure and Stress Corrosion Cracking Behavior of AA2219 Plate to Ring Weld Joints in 3.5 Wt Pct NaCl Solution

A. Venugopal, P. Ramesh Narayanan, S. C. Sharma

Publisher page

Abstract

AA2219 aluminum alloy plate (T87) and ring (T851) were joined by tungsten inert gas (TIG) welding using multi-pass welding. The mechanical properties and stress corrosion cracking (SCC) resistance of the above base metals (BMs) in different directions (L, LT, and ST) were examined. Similarly, the weld metal joined by plate to plate and plate to ring (PR) joints was evaluated. The results revealed that the mechanical properties of the ring were comparatively lower than the plate. This was found to be due to the extremely coarse grain size of the ring along with severe Cu-rich segregation along the grain boundaries when compared to the plate material. The SCC resistance of the base and weldments were found to be good and not susceptible to SCC. This was shown to be due to high values of SCC index (>0.9) and the typical ductile cracking morphology of the BM and the weld joints after SCC test in the environment (3.5 wt pct NaCl) when compared to test performed in the control environment (air). However, the corrosion resistance of the weld interface between the FZ and ring was inferior to the FZ–plate interface.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. D.O. Sprowls and R.H. Brown: in Proc. Conf. on “Fundamental Aspects of Stress Corrosion Cracking” OH, Sept. 11–15, NACE, Houston, TX, 1967, pp. 478–86
2. M.O. Speidel Metall. Trans. A, 1975, vol.6A, pp. 633-52
3. J.R. Simmons, L. Johnson, A. Daech, and R. Merschel: Mater. Perf., 1982, pp. 14–18
4. C.H. Crane and W.G. Smith: Weld. Res. Suppl., 1961, pp. 33s–40s
5. K. Srinivasa Rao, G. Madhusudhan Reddy and K. Prasad Rao, Mater. Sci. Eng. A, 2005, vol.403, pp.69-7610.1016/j.msea.2005.04.041 ↗
6. C. Huang and S. Kou: Weld. Res. Suppl., 2001, pp. 46s–53s
7. C. Huang and S. Kou: Weld. J., 2003, pp. 184s–94s
8. C. Huang and S. Kou: Weld. Res. Suppl., 2000, pp. 113s–20s
9. C. Huang and S. Kou: Weld. Res. Suppl., 2001, pp. 9s–17s
10. K. Srinivasa Rao and K. Prasad Rao, Mater. Sci. Tech. 2005, vol.21 pp. 1199-20710.1179/174328405X51848 ↗
11. J.A. Hartman, R.J. Beil, and G.T. Hahn: Weld. Res. Suppl., 1987, pp. 73s–83s
12. A. Venugopal, K. Sreekumar and V.S. Raja, Metall. Trans. A, 2012, vol.43A, pp.3135-314810.1007/s11661-012-1117-5 ↗
13. A. Venugopal, K. Sreekumar and V.S. Raja, Metall. Trans. A, 2010, vol.41A, pp.3151-316010.1007/s11661-010-0377-1 ↗
14. C.S. Paglia and R.G. Buchheit: Mater. Sci. Eng. A, 2006, vol.429, pp. 107-1410.1016/j.msea.2006.05.036 ↗
15. W. Hu and EI Meletis: Mater. Sci. Forum, 2000, Vols. 331-227, pp. 1683-8810.4028/www.scientific.net/MSF.331-337.1683 ↗
16. P. Bala Srinivasan, K. S. Arora, W. Dietzel, S. Pandey and M.K. Schaper, J. Alloy. Compd., 2009, vol. 492, pp. 631-3710.1016/j.jallcom.2009.11.198 ↗
17. AMS 2772E: Heat Treatment of Aluminium Alloy Raw Material, 2008–02
18. T.F. Morgeneyer, M.J. Starink, S.C. Wang and I. Sinclair, Acta Materialia, 2008, vol. 56, pp.2872-288410.1016/j.actamat.2008.02.021 ↗
19. A.K. Vasudevan and R.D. Doherty, Acta. Metall. 1987, vol.35, pp.1193-121910.1016/0001-6160(87)90001-0 ↗
20. S.D. Liu, B. Chen, C.B. Li, Y. Dai, YlL. Deng and X.M. Zhang: Corros. Sci., 2015, vol.91, pp.203-1210.1016/j.corsci.2014.11.024 ↗
21. F. Song, X. Zhang, S. Liu and K. Li, Corros. Sci., 2014, Vol.78, pp.276-8610.1016/j.corsci.2013.10.010 ↗
22. T. Ramgopal, P.I. Gouma and G.S. Frankel: Corrosion, 2002, vol.58, pp.687-9710.5006/1.3287699 ↗
23. N. Birbilis, M.K. Cavanaugh and R.G. Buchheit, Corros. Sci., 2006, vol.48, pp.4202-1410.1016/j.corsci.2006.02.007 ↗
24. G.O. Llevbare and J.R. Scully, Corrosion 2001, vol.57, pp.134-5210.5006/1.3290339 ↗
25. X.Y. Zhu, C.Y. Deng, Y. Wang, Z.W. Yang, J.K. Ding and D.P. Wang, Materials & Design 2015, vol.65, pp.1075-8210.1016/j.matdes.2014.10.056 ↗