Improvement of Quench Factor Analysis in Phase and Hardness Prediction of a Quenched Steel
Source abstract
Abstract
The accurate prediction of alloys’ properties introduced by heat treatment has been considered by many researchers. The advantages of such predictions are reduction of test trails and materials’ consumption as well as time and energy saving. One of the most important methods to predict hardness in quenched steel parts is Quench Factor Analysis (QFA). Classical QFA is based on the Johnson–Mehl–Avrami-Kolmogorov (JMAK) equation. In this study, a modified form of the QFA based on the work by Rometsch et al. is compared with the classical QFA, and they are applied to prediction of hardness of steels. For this purpose, samples of CK60 steel were utilized as raw material. They were austenitized at 1103 K (830 °C). After quenching in different environments, they were cut and their hardness was determined. In addition, the hardness values of the samples were fitted using the classical and modified equations for the quench factor analysis and the results were compared. Results showed a significant improvement in fitted values of the hardness and proved the higher efficiency of the new method.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. A. Zehtab Yazdi, S.A. Sajjadi, S.M. Zebarjad, S.M. Moosavi Nezhad (2008) J. Mater. Proc. Technol. 199:124-129.10.1016/j.jmatprotec.2007.08.035 ↗
2. J.W. Evancho and J.T. Staley: Metall Trans, 1974, vol. 5, pp. 43-47.10.1007/BF02642924 ↗
3. S.D. Liu, X.M. Zhang, Z.B. Huang and J.H. You: Materials Science Forums, 2007, vol. 546-549, pp. 881-884.10.4028/www.scientific.net/MSF.546-549.881 ↗
4. J.D. Bernardin and I. Mudawar: Inter. J. Heat Mass. Transfer, 1995, vol. 38, pp. 863-873.10.1016/0017-9310(94)00204-9 ↗
5. J.T. Staley and R.D. Doherty: Metall. Trans. A, 1993, vol. 24, pp. 2417-2427.10.1007/BF02646521 ↗
6. J.S. Robinson, D.A. Tanner, van S. Petegem, A. Evans (2012) Mater. Sci. Technol. 28:420-430.10.1179/1743284711Y.0000000063 ↗
7. S.H. Ma and R.D. Sisson: International Heat Treatment & Surface Engineering, 2007, vol. 1, pp. 81-87.10.1179/174951507X193666 ↗
8. S. Ma, M.D. Maniruzzaman, D.S. MacKenzie and R.D. Sisson: Metallurgical and Materials Transactions B, 2007, vol.38, pp.583-589.10.1007/s11663-007-9044-3 ↗
9. P.A. Rometsch and G.B. Schaffer: International Journal of Cast Melals Research, 2000, vol. 12, pp. 431-439.10.1080/13640461.2000.11819380 ↗
10. M. Tiryakioğlu and R.T. Shuey: Metallurgical and Materials Transactions A, 2010, vol. 41, pp. 2984-2991.10.1007/s11661-010-0359-3 ↗
11. M. Tiryakioğlu and R.T. Shuey: Materials Science and Engineering: A, 2010, vol. 527, pp. 5033–5037.10.1016/j.msea.2010.04.060 ↗
12. C.E. Bates and G.E. Totten: Conf. on ‘ Quenching and Distortion Control’, Chicago, USA, 1992, pp. 33–39.
13. G.E. Totten, L.C.F. Canale, A.C. Canale and C.E. Bates: ‘Proceedings - 15th International Federation for Heat Treatment and Surface Engineering Congress’, SAE International, Sao Paulo - Brazil, 2006.
14. G.E. Totten, Y.H. Sun and C.E. Bates: 3rd Int. Conf. on ‘ Quenching and Control of Distortion’, Prague - Czech, 1999.
15. G.E. Totten, Y.H. Sun, G.M. Webster, C.E. Bates and L.M. Jarvis: ‘Quenching and Distortion Control Technology’, Society of Manufacturing Engineers, Chicago - USA, 1998.
16. G.E. Totten, Y.H. Sun and C.E. Bates: 19th Conf. ASM Heat Treating Society, Ohaio, USA, 2000.
17. G.S. Sarmiento, C. Bronzini, A.C. Canale, L.C.F. Canale and G.E. Totten: J. ASTM Int., 2009, vol. 6, pp. 1–18.10.1520/JAI102098 ↗
18. C.E. Bates: J. Heat Treat., 1988, vol. 6, pp. 27-45.10.1007/BF02833162 ↗
19. M. Avrami: J. Chem. Phys., 1939, vol. 7, pp. 1103-1112.10.1063/1.1750380 ↗
20. C.E. Bates: J. Heat Treat., 1987, vol. 5, pp. 27-40.10.1007/BF02831618 ↗
21. J.W. Cahn: Acta Metall., 1956, vol. 4, pp. 449-575.10.1016/0001-6160(56)90041-4 ↗
22. P.A. Rometsch, M.J. Starink and P.J. Gregson: Mater. Sci. Eng. A, 2003, vol. 339, pp. 255-264.10.1016/S0921-5093(02)00110-7 ↗
23. M.J. Starink and A.M. Zahra: Thermochemica Acta, 1996, vol. 292, pp. 159-168.10.1016/S0040-6031(96)03135-8 ↗
24. M.J. Starink: J. Mater. Sci., 2001, vol. 36, pp. 4433-4441.10.1023/A:1017974517877 ↗
25. M.J. Starink (2007) Mater. Sci. Forum 539-543:2365–2370.10.4028/www.scientific.net/MSF.539-543.2365 ↗
26. J.T. Staley: Mater. Sci. technol., 1987, vol. 3, pp. 923-934.10.1179/026708387790220991 ↗
27. C.R. Brooks, Principle of the heat treatment of plain carbon and low alloy steel, ASM international, US, 1996, p.392.10.31399/asm.tb.phtpclas.9781627083539 ↗