Plastic Deformation and Ductility of AA7075 and AA6013 at Warm Temperatures Suitable to Retrogression Forming
Source abstract
Abstract
A warm forming process with a simultaneous retrogression heat treatment, termed retrogression forming, can achieve good formability in high-strength aluminum alloys and recover their high strength through a single reaging heat treatment after forming. Tensile data from two commercial aluminum alloy sheet materials, AA7075-T6 and AA6013-T6, are presented for conditions suitable to retrogression forming. AA7075-T6 sheet was tested at temperatures from 180 °C to 220 °C and strain rates from 3.2 × 10−3 to 10−1 s−1. AA6013-T6 sheet was tested from 230 °C to 250 °C and 3.2 × 10−3 to 10−1 s−1. Both materials exhibit nearly steady-state flow at these temperatures and produce a modest strain-rate sensitivity of m = 0.039. The activation energies for plastic flow under these conditions are 221 kJ/mol for AA7075-T6 and 253 kJ/mol for AA6013-T6. Test data are used to construct predictive models for flow stress as a function of temperature and strain rate. AA7075-T6 demonstrates an excellent potential for retrogression forming at 200 °C and strain rates up to 10−1 s−1 if time at temperature is held to under 12 minutes. AA6013-T6 exhibits a modest potential for retrogression forming at 240 °C and strain rates up to 10−1 s−1 if time at temperature is held to under 7 minutes.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Aluminum Alloy Microstructure Properties · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. R. S. Long, E. Boettcher, and D. Crawford: JOM, 2017, vol. 69, no. 12, pp. 2635-2639.10.1007/s11837-017-2554-9 ↗
2. K. Zheng, D. J. Politis, L. Wang, and J. Lin: Int. J. Light. Mater. Manuf., 2018, vol. 1, no. 2, pp. 55-90.10.1016/j.ijmachtools.2017.10.006 ↗
3. L. R. Morris and R. A. George: SAE Tech. Pap. Ser., 1977, no. 770206.
4. P. E. Krajewski: SAE Tech. Pap. Ser., 2006, no. 2006-01-0984.10.1055/s-2006-949337 ↗
5. N. R. Harrison and S. G. Luckey: SAE Int. J. Mater. Manuf., 2014, vol. 7, no. 3, pp. 567-573.10.4271/2014-01-0981 ↗
6. A. Keci, N. R. Harrison, and S. G. Luckey: SAE Tech. Pap. Ser., 2014, no. 2014-01-0984.
7. J. Mendiguren, E. S. de Argandona, L. Galdos: IOP Conf. Ser. Mater. Sci. Eng., 2016, 159, 1012016.10.1088/1757-899X/159/1/012026 ↗
8. W. Xiao, B. Wang, and K. Zheng: Int. J. Adv. Manuf. Tech., 2017, vol. 92, pp. 3299-3309.10.1007/s00170-017-0419-6 ↗
9. H. Wang, Y. Luo, P. Friedman, M. Chen, and L. Gao: Trans. Nonferr. Met. Soc. China, 2012, vol. 22, pp. 1-7.10.1016/S1003-6326(11)61131-X ↗
10. W. Huo, L. Huo, Y. Zhang, and J. Zhang: Mater. Sci. Eng. A, 2016, vol. 675, pp. 44-54.10.1016/j.msea.2016.08.054 ↗
11. H. Kim, L. Cronley, C. Reichert, P. Zelenak (2017) Int. Auto. Body Cong., 20, 1-11.
12. H. Kim, R. Hagnlen, T. Feister, and V. Tunga: IOP Conf. Ser. Mater. Sci. Eng., 2018, vol. 418, no. 012029, pp. 1-8.
13. T. A. Ivanoff, J. T. Carter, L. G. Hector, Jr., and E. M. Taleff: Metall. Mater. Trans. A, 2019, vol. 50, no. 3, pp. 1545-1561.10.1007/s11661-018-5084-3 ↗
14. E. M. Taleff, P. J. Nevland, and P. E. Krajewski: Metall. Mater. Trans. A, 2001, vol. 32, no. 5, pp. 1119-1130.10.1007/s11661-001-0123-9 ↗
15. ASM Handbook Committee: ASM Handbook, Volume 2: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM International, Materials Park, OH, 1990, pp. 62-122.
16. K. Anderson, J. Weritz, and J. G. Kaufman (eds.): ASM Handbook, Volume 2B: Properties and Selection of Aluminum Alloys, 2019, pp. 432-438.10.31399/asm.hb.v02b.9781627082105 ↗
17. M. B. Kannan, P. B. Srinivasan, and V. S. Raja: Stress Corrosion Cracking, Woodhead Publishing, 2011, pp. 307-340.
18. J. P. Immarigon, R. T. Holt, A. K. Koul, L. Zhao, W. Wallace, and J. C. Beddos: Mater. Char., 1995, vol. 35, pp. 41-67.10.1016/1044-5803(95)00066-6 ↗
19. N. C. Danh, K. Rajan, and W. Wallace: Metall. Trans. A, 1983, vol. 14, no. 9, pp. 1843-1850.10.1007/BF02645554 ↗
20. Alcoa Inc.: Alcoa Technical Fact Sheet: Alloy 6013 sheet: Maximum Strength 6xxx Series Sheet, Alcoa Inc., Bettendorf, Iowa, 2017.
21. V. Burt: ASM Handbook, Volume 2A: Aluminum Science and Technology, 2018, pp. 336–356.10.31399/asm.hb.v02a.a0006527 ↗
22. M. Kumar and N. G. Ross: J. Mater. Process. Tech., 2016, vol. 231, pp. 189-198.10.1016/j.jmatprotec.2015.12.026 ↗
23. M. Aumüller (2014) AluReport, 24: 14-15.
24. K. E. Rader, T. A. Ivanoff, H. Shin, J. Carter, L. G. Hector, Jr., and E. M. Taleff: Light Metals 2018, 2018, pp. 241-246.
25. K. E. Rader, J. Carter, L. Hector, Jr., and E. M. Taleff: Light Metals 2019, 2019, pp. 159-164.
26. K. E. Rader, M. Schick, J. Carter, L. Hector, Jr., and E. M. Taleff: Light Metals 2019, 2019, pp. 187-191.
27. K. E. Rader, J. Carter, L. Hector, Jr., and E. M. Taleff: Light Metals 2020, 2020, pp. 400-405.
28. K. E. Rader, J. Carter, L. Hector, Jr., and E. M. Taleff: Light Metals 2020, 2020, pp. 247-252.
29. K. E. Rader, J. Carter, L. Hector, Jr., and E. M. Taleff: Light Metals, 2021.
30. K. E. Rader, J. Carter, L. Hector, Jr., and E. M. Taleff: Metall. Mater. Trans. A, 2021.
31. J. K. Park and A. J. Ardell: Metall. Trans. A, 1984, vol. 15, pp. 1531-1543.10.1007/BF02657792 ↗
32. Alcoa Inc.: Alcoa Technical Fact Sheet: Alloy 7075 Plate and Sheet, Alcoa Inc., Bettendorf, Iowa, 2017
33. ASTM E8: ASTM International, West Conshohocken, PA, 2017.
34. ASTM E2448: ASTM International, West Conshohocken, PA, 2017.
35. ASTM E385-17: ASTM International, West Conshohocken, PA, 2017.
36. ASTM E6: ASTM International, West Conshohocken, PA, 2017.
37. V. W. Köster: Zeitschrift fut Metall., 1948, vol. 39, pp. 1-12.
38. R. N. Lumley, A. J. Morton, R. G. O’Donnell, and I. J. Polmear: Heat Treat. Prog., 2005, vol. 5, no. 2, pp. 23-29.
39. L. Zhuang, R. de Haan, J. Bottema, C. T. W. Lahaye, and P. De Smet: Mater. Sci. Forum, 2000, vol. 331-337, pp. 1309-1314.10.4028/www.scientific.net/MSF.331-337.1309 ↗
40. D. C. Balderach, J. A. Hamilton, E. Leung, M. C. Trejeda, J. Qiao, and E. M. Taleff: Mater. Sci. Eng. A, 2002, vol. 339, pp. 194-204.10.1016/S0921-5093(02)00158-2 ↗
41. J. H. Hollomon: Trans. AIME, 1945, vol. 162, pp. 268-290.
42. The MathWorks, Inc.: MATLAB [Software], Version R2016b, 2016, Available from https://www.mathworks.com/products/matlab.
43. O. G. Sherby and P. M. Burke: Prog. Mater. Sci., 1968, vol. 13, pp. 325-390.10.1016/0079-6425(68)90024-8 ↗
44. M. E. Kassner (2015) Fundamentals of Creep in Metals and Alloys, Butterworth Heinemann,Waltham.
45. O. D. Sherby, R. L. Orr, and J. E. Dorn: Trans. AIME, 1954, vol. 1954, pp. 71-80.
46. J. J. Jonas, C. M. Sellars, W. J. McG. Tegart: Metall. Rev., 1969, vol. 14, no. 1, pp. 1-24.10.1179/095066069790138056 ↗
47. E. U. Lee, H. H. Kranzlein, E. E. Underwood: Mater. Sci. Eng., 1971, vol. 7, no. 6, pp. 348-356.10.1016/0025-5416(71)90018-8 ↗
48. T. G. Langdon: Metall. Trans. A, 1982, vol. 13, pp. 689-701.10.1007/BF02642383 ↗
49. J. Noder: Master’s Thesis, 2017, Univ. of Waterloo, Canada.
50. H. Rong, P. Hu, L. Ying, W. Hou, and J. Zhang: Int. J. Mech. Sci., 2019, vol. 156, pp. 59-73.10.1016/j.ijmecsci.2019.03.027 ↗
51. C. Zener and J. H. Hollomon: J. Appl. Phys., 1944, vol. 15, no. 1, pp. 22-32.10.1063/1.1707363 ↗
52. D. A. Woodford: Trans. ASM, 1969, vol. 62, pp. 291-293.
53. M. A. Burke and W. D. Nix: Acta Metall., 1975, vol. 23, pp. 793-798.10.1016/0001-6160(75)90195-9 ↗
54. J. W. Hutchinson and H. Obrecht: Fracture, 1977, vol. 1, pp. 101-116.
55. J. W. Hutchinson and K. W. Neale (1983) J. Mech. Phys. Solids, 31(5), 405-426.10.1016/0022-5096(83)90007-8 ↗