journal article·2020-12

Effect of Pin Length and Rotation Speed on the Microstructure and Mechanical Properties of Friction Stir Welded Lap Joints of AZ31B-H24 Mg Alloy and AA6061-T6 Al Alloy

Anil Bandi, Srinivasa R. Bakshi

Publisher page

Abstract

In the present work, friction stir welding of 3-mm-thick AA6061-T6 Al alloy and AZ31B-H24 Mg alloy sheets was carried out in lap configuration with Al alloy on top. Experiments were carried out by varying the pin length (3.25, 3.75, and 4.25 mm) and tool rotation speed (600, 800, and 1000 RPM). Microstructures of the joint cross-section revealed the presence of a compound intermetallic layer along the interface consisting of Al-rich (Al3Mg2) intermetallic compound near the Al alloy side, and Mg-rich intermetallic compound (Mg17Al12) near the Mg alloy side. The formation of a eutectic mixture of Mg solid solution and Mg17Al12 was observed at the hook on either side. Two modes of failure were observed; Mode 1 through the interface and Mode 2 due to failure of the sheet. The Mode 1 failure strengths obtained were the highest (148 ± 6 N/mm) compared to the literature and were obtained for the 3.25 and 3.75 mm pin at 800 RPM. A lap shear strength of 212 ± 6 N/mm was obtained with 4.25 mm pin length at 600 RPM, which is the highest reported so far and was attributed to Mode 2 failure. The effect of interface pull-up, angle of the interface at the advancing side, and distribution of intermetallic compounds on the lap-shear strength are discussed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · MXene and MAX Phase Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. 1 B.L. Mordike and T. Ebert: Mater. Sci. Eng. A, 2001, vol. 302, pp. 37–45.10.1016/S0921-5093(00)01351-4 ↗
2. B. Guang, L. Song, and A. Atrens: Adv. Eng. Mater., 1999, pp. 11–33.
3. 3 H. Friedrich and S. Schumann: J. Mater. Process. Technol., 2001, vol. 117, pp. 276–81.10.1016/S0924-0136(01)00780-4 ↗
4. Murray J.L: Bin. Alloy Phase Diagrams, Second Ed., T.B. Massalski, ed., ASM International, Materials Park, Ohio, 1990, pp. 169–71.
5. 5 R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng. R Reports, 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
6. 6 C.M. Chen and R. Kovacevic: Int. J. Mach. Tools Manuf., 2004, vol. 44, pp. 1205–14.10.1016/j.ijmachtools.2004.03.011 ↗
7. 7 J. Ouyang, E. Yarrapareddy, and R. Kovacevic: J. Mater. Process. Technol., 2006, vol. 172, pp. 110–22.10.1016/j.jmatprotec.2005.09.013 ↗
8. 8 Y.C. Chen and K. Nakata: Mater. Des., 2009, vol. 30, pp. 469–74.10.1016/j.matdes.2008.06.008 ↗
9. 9 M. Fazel-Najafabadi, S.F. Kashani-Bozorg, and A. Zarei-Hanzaki: Mater. Des., 2010, vol. 31, pp. 4800–7.10.1016/j.matdes.2010.05.003 ↗
10. 10 Y. Li, L.E. Murr, and J.C. McClure: Mater. Sci. Eng. A, 1999, vol. 271, pp. 213–23.10.1016/S0921-5093(99)00204-X ↗
11. 11 A.C. Somasekharan and L.E. Murr: Mater. Charact., 2004, vol. 52, pp. 49–64.10.1016/j.matchar.2004.03.005 ↗
12. 12 Y.S. Sato, S.H.C. Park, M. Michiuchi, and H. Kokawa: Scr. Mater., 2004, vol. 50, pp. 1233–6.10.1016/j.scriptamat.2004.02.002 ↗
13. 13 N. Yamamoto, J. Liao, S. Watanabe, and K. Nakata: Mater. Trans., 2009, vol. 50, pp. 2833–8.10.2320/matertrans.M2009289 ↗
14. S. Ji, X. Meng, Z. Liu, R. Huang, and Z. Li (2017) Mater. Lett., https://doi.org/10.1016/j.matlet.2017.05.011.10.1016/j.matlet.2017.05.011 ↗
15. 15 Z. Liu, X. Meng, S. Ji, Z. Li, and L. Wang: J. Manuf. Process., 2018, vol. 31, pp. 552–9.10.1016/j.jmapro.2017.12.022 ↗
16. 16 X. Lv, C.S. Wu, C. Yang, and G.K. Padhy: J. Mater. Process. Technol., 2018, vol. 254, pp. 145–57.10.1016/j.jmatprotec.2017.11.031 ↗
17. 17 K.P. Mehta, P. Carlone, A. Astarita, F. Scherillo, F. Rubino, and P. Vora: Mater. Sci. Eng. A, 2019, vol. 759, pp. 252–61.10.1016/j.msea.2019.04.120 ↗
18. 18 Y.C. Chen and K. Nakata: Scr. Mater., 2008, vol. 58, pp. 433–6.10.1016/j.scriptamat.2007.10.033 ↗
19. 19 V. Firouzdor and S. Kou: Supp. to Weld. J., 2009, vol. 88, pp. 213–24.
20. 20 J. Mohammadi, Y. Behnamian, A. Mostafaei, H. Izadi, T. Saeid, A.H. Kokabi, and A.P. Gerlich: Mater. Charact., 2015, vol. 101, pp. 189–207.10.1016/j.matchar.2015.01.008 ↗
21. 21 S. Ji, Z. Li, L. Zhang, Z. Zhou, and P. Chai: Mater. Des., 2016, vol. 103, pp. 160–70.10.1016/j.matdes.2016.04.066 ↗
22. 22 H.M. Rao, B. Ghaffari, W. Yuan, J.B. Jordon, and H. Badarinarayan: Mater. Sci. Eng. A, 2016, vol. 651, pp. 27–36.10.1016/j.msea.2015.10.082 ↗
23. 23 S. Tan, F. Zheng, J. Chen, J. Han, Y. Wu, and L. Peng: J. Magnes. Alloy., 2017, vol. 5, pp. 56–63.10.1016/j.jma.2016.11.005 ↗
24. 24 S. Niu, S. Ji, D. Yan, X. Meng, and X. Xiong: J. Mater. Process. Technol., 2019, vol. 263, pp. 82–90.10.1016/j.jmatprotec.2018.08.009 ↗
25. 25 S. Ji, S. Niu, J. Liu, and X. Meng: J. Mater. Process. Technol., 2019, vol. 267, pp. 141–51.10.1016/j.jmatprotec.2018.12.010 ↗
26. 26 Y. Gao, K. Nakata, K. Nagatsuka, Y. Shibata, and M. Amano: J. Mater. Process. Technol., 2016, vol. 229, pp. 313–21.10.1016/j.jmatprotec.2015.09.029 ↗
27. 27 S.D. Ji, Q. Wen, and Z.W. Li: J. Mater. Sci. Technol., 2020, vol. 48, pp. 23–30.10.1016/j.jmst.2020.01.042 ↗
28. 28 L. Cederqvist and A.P. Reynolds: Supp. to Weld. J., 2001, vol. 80, pp. 281–7.
29. 29 G. Buffa, G. Campanile, L. Fratini, and A. Prisco: Mater. Sci. Eng. A, 2009, vol. 519, pp. 19–26.10.1016/j.msea.2009.04.046 ↗
30. 30 A. Chapuis and J.H. Driver: Acta Mater., 2011, vol. 59, pp. 1986–94.10.1016/j.actamat.2010.11.064 ↗
31. 31 T.U. Seidel and A.P. Reynolds: Metall. Mater. Trans. A, 2001, vol. 32, pp. 2879–84.10.1007/s11661-001-1038-1 ↗
32. 32 J.W. Pew, T.W. Nelson, and C.D. Sorensen: Sci. Technol. Weld. Join., 2007, vol. 12, pp. 341–7.10.1179/174329307X197601 ↗
33. Y.K. Y.K. Yang, H. Dong, H. Cao, Y.A. Chang, and S. Kou: Supp. to Weld. J., 2008, vol. 87, pp. 167–77.
34. V. Firouzdor and S. Kou: Metall. Mater. Trans. A Phys. Metall. Mater. Sci., 2010, vol. 41, pp. 2914–35.10.1007/s11661-010-0340-1 ↗
35. 35 R. Nandan, G.G. Roy, and T. Debroy: Met. Mater. Trans. A, 2006, vol. 37A, pp. 1247–59.10.1007/s11661-006-1076-9 ↗
36. 36 R. Nandan, T. Debroy, and H.K.D.H. Bhadeshia: Prog. Mater. Sci., 2008, vol. 53, pp. 980–1023.10.1016/j.pmatsci.2008.05.001 ↗
37. 37 J.L. Song, S.B. Lin, C.L. Yang, and C.L. Fan: J. Alloys Compd., 2009, vol. 488, pp. 217–22.10.1016/j.jallcom.2009.08.084 ↗
38. S. Babu, S.K. Panigrahi, G.D. JanakiRam, P. V. Venkitakrishnan, and R. SureshKumar: J. Mater. Process. Technol., 2018, vol. 266, pp. 155–64.10.1016/j.jmatprotec.2018.10.034 ↗
39. 39 L. Boccarusso, A. Astarita, P. Carlone, F. Scherillo, F. Rubino, and A. Squillace: J. Manuf. Process., 2019, vol. 44, pp. 376–88.10.1016/j.jmapro.2019.06.022 ↗
40. V. Firouzdor and S. Kou: Metall. Mater. Trans. A Phys. Metall. Mater. Sci., 2010, vol. 41, pp. 3238–51.10.1007/s11661-010-0366-4 ↗
41. 41 H.M. Rao, W. Yuan, and H. Badarinarayan: Mater. Des., 2015, vol. 66, pp. 235–45.10.1016/j.matdes.2014.10.065 ↗
42. 42 H. Schmidt, J. Hattel, and J. Wert: Model. Simul. Mater. Sci. Eng., 2004, vol. 12, pp. 143–57.10.1088/0965-0393/12/1/013 ↗