A Critical Assessment of Cyclic Softening and Hardening Behavior in a Near-α Titanium Alloy During Thermomechanical Fatigue
Source abstract
Abstract
Thermomechanical fatigue behavior of Ti-alloy Timetal 834 has been studied at two temperature intervals viz. 573 K to 723 K (300 °C to 450 °C) and 723 K to 873 K (450 °C to 600 °C) under mechanical strain-controlled cycling. Among the temperatures studied, the alloy exhibited initial cyclic softening followed by cyclic hardening at 723 K (450 °C) in the temperature interval of 573 K to 723 K (300 °C to 450 °C). However, continuous cyclic hardening was observed at 723 K (450 °C) in 723 K to 873 K (450 °C to 600 °C). At 573 K (300 °C) and 873 K (600 °C), cyclic softening was observed in the cyclic stress response curves in both the temperature intervals. The dislocation substructure was observed to be planar in both the modes of TMF loading. Based on TEM microstructures and few unconventional fatigue tests, the observed cyclic hardening is attributed to dynamic strain aging. The reduced fatigue life at 723 K to 873 K (450 °C to 600 °C) under OP-TMF loading was attributed to the combined effect of cyclic hardening (leading to early strain localization and crack initiation), oxidation, and development of tensile mean stresses.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Nuclear Materials and Properties · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (64)
Show source-provided references
1. C. Soares, Gas Turbines: A Handbook of Air, Land and Sea applications. Butterworth-Heinemann, New York, NY, 2008, pp. 679-71610.1016/B978-075067969-5.50024-7 ↗
2. M. P. Boyce: Gas Turbine Engineering Handbook. 4th edition. Butterworth-Heinemann, New York, NY, 2012, pp. 803–883.10.1016/B978-0-12-383842-1.00021-4 ↗
3. R. C. Reed: The Superalloys: Fundamentals and Applications, Cambridge University Press, Cambridge, 200610.1017/CBO9780511541285 ↗
4. [4] H. Sehitoglu: J. Eng. Mater. Technol.,1985, vol. 107, pp. 221-22610.1115/1.3225805 ↗
5. [5] R. Viswanathan: Damage Mechanisms and Life Assessment of High Temperature Components, ASM International, 2nd Edition, Ohio, US, 1993
6. [6] R. J. Lancaster, M. T. Whittaker, and S. J. Williams: Mater. High Temperature.2013, vol. 30, pp. 2-1210.3184/096034013X13630238172260 ↗
7. [7] K. Prasad, and V. Kumar: Mater. Sci. Eng. A.,2011, vol. 528A, pp. 6263-627010.1016/j.msea.2011.04.085 ↗
8. K. Prasad, Phani. S. Karamched, A. Bhattacharjee, V. Kumar, K. Bhanu Sankara Rao, and M. Sundararaman: Mater. Design, 2015, vol. 65, pp. 297-31110.1016/j.matdes.2014.09.006 ↗
9. [9] K. Prasad, V. Kumar, K. Bhanu Sankara Rao, and M. Sundararaman: Metall. Mater. Trans. A., 2016, vol. 47, pp. 3713-373010.1007/s11661-016-3482-y ↗
10. D. F. Neal. Development and evaluation of high temperature titanium alloy IMI 834, in P. Lacombe, R. Tricot, G. Beranger (Eds.), Proceedings of 6th world conference on titanium, Cannes, France, 1988, p. 253-258
11. D. F. Neal, and S. P. Fox. The influence of Silicon and Silicides on the properties of Near Alpha Titanium Alloys, In: F. H. Froes and I. Caplan (Eds.), Titanium 92 Science and Technology, The Minerals, Metals & Materials Society, Warrendale, 1993, p. 287-294.
12. G. Lütjering, and J. C. Williams: Titanium, 2nd Edition, Springer, New York, 2007.
13. [13] E. S. Sounim: Metall. Mater. Trans. A,2001, vol. 32A, 285-29310.1007/s11661-001-0260-1 ↗
14. [14] S. Hardt, H. J. Maier, and H. J. Christ:Int. J. Fatigue.1999, vol. 21, pp. 779-78910.1016/S0142-1123(99)00042-0 ↗
15. [15] K. Prasad, and V. K. Varma: Mater. Sci. Eng. A.,2008, vol. 486A, pp. 158-166.10.1016/j.msea.2007.09.020 ↗
16. [16] K. Prasad, and S. V. Kamat: Mater. Sci. Eng. A,2008, vol. 490A, pp. 477-48010.1016/j.msea.2008.01.005 ↗
17. [17] K. Prasad, R. Sarkar, P. Ghosal, and V. K. Varma: Mater. Sci. Eng. A.,2008, vol. 494A, pp. 227-3110.1016/j.msea.2008.04.025 ↗
18. [18] K. Prasad, and V. Kumar: Mater. Design.2011, vol. 32, pp. 1710-1510.1016/j.matdes.2010.08.044 ↗
19. [19] N. Singh and V. Singh: Mater. Sci. Eng. A,2008, vol. 485A, pp. 130-13910.1016/j.msea.2007.07.064 ↗
20. [20] P. Pototzky, H. J. Maier, and H. J. Christ:Metall. Mater. Trans. A.,1998, vol. 29A, pp. 2995-300410.1007/s11661-998-0207-x ↗
21. P. Pototzky, H. J. Maier, and H.J. Christ. Behavior of the high temperature titanium alloy IMI 834 under thermomechanical and isothermal fatigue conditions. In: Third symposium on thermo-mechanical fatigue behavior of materials, H. Sehitoglu and H. J. Maier (Eds.), ASTM STP 1371, West Conshohocken (PA): 1999, pp. 18–3510.1520/STP15251S ↗
22. Christ HJ (2007). Materials Science and Engineering: A, 468, 98-108.10.1016/j.msea.2006.08.132 ↗
23. [23] H. J. Maier, and H. J. Christ:Int. J. Fatigue.1997, vol. 19, pp. S267-S27410.1016/S0142-1123(97)00022-4 ↗
24. ASTM Standard E 2368-10: Standard practice for strain controlled thermomechanical fatigue testing, In: Annual book of ASTM standards, vol. 3.01, ASTM International, West Conshohocken, 2010
25. C. Ramchandra, A. K. Singh, and G. V. K. Sharma: Metall. Trans. A,1993, vol. 24, pp. 1273-128010.1007/BF02668196 ↗
26. N. Singh, PhD Thesis, Banaras Hindu University, Varanasi, 2004, India
27. [27] K. Prasad, R. Sarkar, V. Kumar, K. Bhanu Sankara Rao, and M. Sundararaman: Mater. Sci. Eng. A., 2016, vol. 662, pp. 373-38410.1016/j.msea.2016.03.079 ↗
28. H. Renner, H. Kestler, and H. Mughrabi, Influence of heat treatment and microstructure on the low cycle fatigue properties of the hot forgerd near –α titanium alloy IMI 834, In: Fatigue ’96, Procrrdings of the sixth international congress. G. Lütjering and H Nowack (Eds.), Oxford: Pergamo, 1996, pp. 935-94010.1016/B978-008042268-8/50033-2 ↗
29. [29] M. E. Nixon, O Cazacu, and R A Lebensohn: Int. J. Plasticity, 2010, vol. 26, pp. 516-53210.1016/j.ijplas.2009.08.007 ↗
30. [30] T. Neeraj, M F Savage, J. Tatalovich, L. Kovarik, R. W. Hayes, and M. J. Mills: Phil. Mag., 2005, vol. 85, pp. 279-29510.1080/14786430412331315707 ↗
31. [31] A. S. Beranger, X. Feaugas, and M. Clavel: Mater. Sci. Eng. A.,1993, vol. 172A, pp. 31-4110.1016/0921-5093(93)90423-C ↗
32. [32] J. C. Williams, R. G. Baggerly, and N. E. Paton: Metall. Mater. Trans. A.,2002, vol. 33A, pp. 837-85010.1007/s11661-002-0153-y ↗
33. M. J. Blackburn: Trans. Met. Soc. AIME,1967, vol. 239, pp. 1200-1208.
34. [34] F. A. Crossley: Metall. Trans.,1970, vol. 1, pp. 1921-192910.1007/BF02642792 ↗
35. [35] C. E. Shamblen, and T. K. Redden: Metall. Trans.,1972, vol. 3, 1299-130510.1007/BF02642464 ↗
36. [36] D. J. Truax, and C. J. McMahon Jr: Mater. Sci. Eng. A.,1974, vol. 13A, pp. 12510.1016/0025-5416(74)90181-5 ↗
37. [37] T. K. G. Namboodhiri, C. J. McMahon Jr, and H. Herman: Metall. Trans.,1973, vol. 4, pp. 1323-133110.1007/BF02644528 ↗
38. [38] W. J. Donlon, J. E. Allison, J. V. Laseki. The influence of thermal exposure on properties and microstructure of elevated temperature titanium alloys, In: F. H. Froes, I. Caplan (Eds.), Titanium ’92 Science and Technology, TMS, Warrendale, 1993, pp. 295-302
39. M. T. Cope, M. J. Hill, The influence of aging temperature on the mechanical properties of IMI 834, In: Proceedings of the sixth world conf. on titanium, P Lacombe, R. Tricot, G. Beranger (Eds.)., France, 1988, pp. 153-158.
40. [40] A. P. Woodfield, P. J. Postans, M. H. Loretto, and R. E. Smallman: Acta Metall., 1988, vol. 36, pp. 507-1510.1016/0001-6160(88)90082-X ↗
41. A. Madsen, E. Andrieu, and H. Ghonem: Mater. Sci. Eng. A.,1993, vol. 171A, pp. 191-19710.1016/0921-5093(93)90406-5 ↗
42. [42] X. D. Zhang, J. M. K. Wiezorek, W. A. Baeslack, D. J. Evans, and H. L. Fraser: Acta Mater.,1998, vol. 46, pp. 4485-4495.10.1016/S1359-6454(98)00158-X ↗
43. [43] G. J. Baxter, W. M. Rainforth, and L. Grabowski: Acta Mater., 1996, vol.44, pp.3453-346310.1016/1359-6454(96)00024-9 ↗
44. K. Gopinath, A. K. Gogia, S. V. Kamat, R. Balamuralikrishnan, and U. Ramamurty: Acta. Mater., 2009, vol. 57, pp. 3450-345910.1016/j.actamat.2009.03.046 ↗
45. [45] P. G. McCormick: Acta. Metall.,1972, vol. 20, pp. 351-35410.1016/0001-6160(72)90028-4 ↗
46. [46] A Van den Beukel: Physica status Solidi,1975, vol. 30, pp. 19710.1002/pssa.2210300120 ↗
47. [47] A Van den Beukel, and U. F. Kocks: Acta Metall.,1982, vol. 30, pp. 1027-103410.1016/0001-6160(82)90211-5 ↗
48. [48] Y. Estrin, and L. P. Kubin: Mater. Sci. Eng. A.,1991, vol. 137A, pp. 125-13410.1016/0921-5093(91)90326-I ↗
49. [49] P. Hähner: Mater. Sci. Eng. A.,1996, vol. 207A, pp. 208-21510.1016/0921-5093(95)10033-4 ↗
50. [50] K. Prasad, S. Amrithapandian, B. K. Panigrahi, V. Kumar, K. Bhanu Sankara Rao, and M. Sundararaman: Mater. Sci. Eng. A.,2015, vol. 638A, pp. 90-9610.1016/j.msea.2015.04.060 ↗
51. [51] M. A. Soare, and W. A. Curtin: Acta Mater.,2008, vol. 56,pp. 4046-406110.1016/j.actamat.2008.04.027 ↗
52. [52] T. Tabata, H. Fujita, and Y. Nakajima: Acta Metall.,1980, vol. 28, pp. 795-80510.1016/0001-6160(80)90156-X ↗
53. [53] H. Fujita, and T. Tabata: Acta Metall.1977, vol. 25, pp. 793-80010.1016/0001-6160(77)90094-3 ↗
54. [54] K. Tsuzaki, T. Hori, T. Maki, and I. Tamura: Mater. Sci. Eng. A.,1983, vol. 61A, pp. 247-26010.1016/0025-5416(83)90107-6 ↗
55. [55] K. Tsuzaki, Y. Matsuzaki, T. Maki, and I. Tamura: Mater Sci Eng. A.,1991, vol. 142A, pp. 63-7010.1016/0921-5093(91)90754-B ↗
56. M.G. Castelli, R.V. Miner, and D.N. Robinson: Thermomechanical fatigue deformation behavior of a dynamic strain aging alloy, Hastelloy X, In: Thermomechanical fatigue behavior of materials, Sehitoglu H (Ed.,), ASTM STP 1186, Philadelphia (PA), 1993, pp. 107–2510.1520/STP24252S ↗
57. [57] Z. Y. Huang, J-L Chaboche, Q. Y. Wang, D. Wagner, and C. Bathias: Mater Sci Eng. A., 2014, vol. 589A, pp. 34-4010.1016/j.msea.2013.09.058 ↗
58. [58] H. M. Rosenberg: Vacancies and other point defects in metals and alloys, Institute of metals, London, 1958, p. 206
59. [59] H. Mecking, and Y. Estrin: Scripta Metall.,1980, vol. 14, pp. 815-81910.1016/0036-9748(80)90295-1 ↗
60. R. E. Reed-Hill, R. Abbaschian, and L. Abbaschian: Physical metallurgy principles. 3rd edition. Thomson Asia (P) Ltd., Singapore. 2003
61. [61] T. H. Sanders, and E. A. Starke Jr.: Metall. Trans. A.,1976, vol. 7A, pp. 1407-140810.1007/BF02658827 ↗
62. [62] K. Bhanu Sankara Rao, H. Schiffers, H. Schuster, and G. R. Halford: Metall. Mater. Trans. A.,1996, vol. 27A, pp. 255-26710.1007/BF02648404 ↗
63. [63] S. D. Antolovich, and R. W. Armstrong: Prog. Mater. Sci.,2014, vol. 59, pp. 1-160.10.1016/j.pmatsci.2013.06.001 ↗
64. [64] K. Prasad, S. Abhaya, G. Amarendra, Vikas Kumar, K. V. Rajulapati, and K. Bhanu Sankara Rao: Eng. Fract. Mech.,2013, vol. 102, pp. 194-20610.1016/j.engfracmech.2013.02.017 ↗