Analysis of Slip Activity and Deformation Modes in Tension and Tension-Creep Tests of Cast Mg-10Gd-3Y-0.5Zr (Wt Pct) at Elevated Temperatures Using In Situ SEM Experiments
Source abstract
Abstract
The tension and tension-creep deformation behavior at elevated temperatures of a cast Mg-10Gd-3Y-0.5Zr (wt pct, GW103) alloy was investigated using in situ scanning electron microscopy. The tests were performed at temperatures ranging from 473 K to 598 K (200 °C to 325 °C). The active slip systems were identified using an EBSD-based slip trace analysis methodology. The results showed that for all of the tests, basal slip was the most likely system to be activated, and non-basal slip was activated to some extent depending on the temperature. No twinning was observed. For the tension tests, non-basal slip consisted of ~35 pct of the deformation modes at low temperatures (473 K and 523 K (200 °C and 250 °C)), while non-basal slip accounted for 12 and 7 pct of the deformation modes at high temperatures (573 K and 598 K (300 °C and 325 °C)), respectively. For the tension-creep tests, non-basal slip accounted for 31 pct of the total slip systems at low temperatures, while this value decreased to 10 to 16 pct at high temperatures. For a given temperature, the relative activity for prismatic slip in the tension-creep tests was slightly greater than that for the tension tests, while the activity for pyramidal slip was lower. Slip-transfer in neighboring grains was observed for the low-temperature tests. Intergranular cracking was the main cracking mode, while some intragranular cracks were observed for the tension-creep tests at high temperature and low stress. Grain boundary ledges were prevalently observed for both the tension and tension-creep tests at high temperatures, which suggests that besides dislocation slip, grain boundary sliding also contributed to the deformation.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (56)
Show source-provided references
1. H. Friedrich and S. Schumann: J. Mater. Process. Tech., 2001, vol. 117, pp. 276-81.10.1016/S0924-0136(01)00780-4 ↗
2. B.L. Mordike: J. Mater. Process. Tech., 2001, vol. 117, pp. 391-4.10.1016/S0924-0136(01)00793-2 ↗
3. N. Zeumer, B. Mordike and K.U. Kainer, eds.: in Proceedings of the Magnesium Alloys and their Applications, Werkstoff-Information-Sgesellschaft, Wolfsburg, Germany, 1998, pp. 125–132.
4. L.L. Rokhlin: Magnesium Alloys Containing Rare Earth Metals, Taylor and Francis, London, UK, 2003, p. 1.10.1201/9781482265163 ↗
5. B.L. Mordike: Mater. Sci. Eng. A, 2002, vol. 324, pp. 103-12.10.1016/S0921-5093(01)01290-4 ↗
6. A.A. Luo: Int. Mater. Rev., 2004, vol. 49, pp. 13-30.10.1179/095066004225010497 ↗
7. M. Pekguleryuz and M. Celikin: Int. Mater. Rev., 2010, vol. 55, pp. 197-217.10.1179/095066010X12646898728327 ↗
8. J.G. Wang, L. M. Hsiung, T.G. Nieh and M. Mabuchi: Mater. Sci. Eng. A, 2001, vol. 315, pp. 81-8.10.1016/S0921-5093(01)01209-6 ↗
9. A. Kielbusa and T. Rzychonb: Procedia Eng., 2011, vol. 10, pp. 1835-40.10.1016/j.proeng.2011.04.305 ↗
10. J.F. Nie, X. Gao and S.M. Zhu: Scripta Mater., 2005, vol. 53, pp. 1049-53.10.1016/j.scriptamat.2005.07.004 ↗
11. W.F. Xu, Y. Zhang, J.R. Terbush, L.M. Peng, W.J. Ding and J.F. Nie: Metall. Mater. Trans. A, 2014, vol. 45, pp. 4103-16.10.1007/s11661-014-2335-9 ↗
12. D.D. Yin, Q.D. Wang, C.J. Boehlert and V. Janik: Metall. Mater. Trans. A, 2013, vol. 43, pp. 3338-50.
13. S. Kamado, Y. Kojima, R. Ninomiya and K. Kubota, in Proceedings of the Third International Magnesium Conference, G.W. Lorimer, ed., Institute of Materials, Mancherster, UK, 1997, p. 327.
14. I.A. Anyanwu, S. Kamado and Y. Kojima: Mater. Trans., 2001, vol. 42, pp. 1206-11.10.2320/matertrans.42.1206 ↗
15. I.A. Anyanwu, S. Kamado and Y. Kojima: Mater. Trans., 2001, vol. 42, pp. 1212-8.10.2320/matertrans.42.1212 ↗
16. S.M. He, X.Q. Zeng, L.M. Peng, X. Gao, J.F. Nie and W.J. Ding: J. Alloy Compd., 2006, vol. 421, pp. 309-13.10.1016/j.jallcom.2005.11.046 ↗
17. S.M. He, X.Q. Zeng, L.M. Peng, X. Gao, J.F. Nie and W.J. Ding: J. Alloy Compd., 2007, vol. 427, pp. 316-23.10.1016/j.jallcom.2006.03.015 ↗
18. V. Janik, D.D. Yin, Q.D. Wang, S.M. He, C.J. Chen, Z. Chen and C.J. Boehlert: Mater. Sci. Eng. A, 2011, vol. 528, pp. 3105-12.10.1016/j.msea.2010.12.089 ↗
19. H. Wang, Q.D. Wang, D.D. Yin, J. Yuan and B. Ye: Mater. Sci. Eng. A, 2013, vol. 578, pp. 150-9.10.1016/j.msea.2013.04.068 ↗
20. H. Wang, Q.D. Wang, C.J. Boehlert, D.D. Yin and J. Yuan: Mater. Charact., 2015, vol. 99, pp. 25-37.10.1016/j.matchar.2014.11.006 ↗
21. H. Wang, Q.D. Wang, D.D. Yin, J. Yuan and B. Ye: Mater. Sci. Forum, 2013, vol. 765, pp. 568-73.10.4028/www.scientific.net/MSF.765.568 ↗
22. H. Wang, Q.D. Wang, C.J. Boehlert, J. Yang, D.D. Yin, J. Yuan and W.J. Ding: Mater. Sci. Eng. A, 2016, vol. 649, pp. 313-24.10.1016/j.msea.2015.10.001 ↗
23. H. Yoshinaga and R. Horiuchi: T. Jpn. I. Met., 1964, vol 5, pp. 14-21.10.2320/matertrans1960.5.14 ↗
24. J.A. Del Valle and O.A. Ruano: Mater. Lett., 2008, vol. 62, pp. 3391-4.10.1016/j.matlet.2008.03.023 ↗
25. J.A. Del Valle, M.T. Perez-Prado and O.A. Ruano: Metall. Mater. Trans. A, 2005, vol. 36, pp. 1427-38.10.1007/s11661-005-0235-8 ↗
26. S.R. Agnew and Ö. Duygulu: Int. J. Plast., 2005, vol. 21, pp. 1161-93.10.1016/j.ijplas.2004.05.018 ↗
27. S.R. Agnew and M.H. Yoo: Acta Mater., 2001, vol. 49, pp. 4277-89.10.1016/S1359-6454(01)00297-X ↗
28. S.R. Agnew, C.N. Tomé, D.W. Brown, T.M. Holden and S.C. Vogel: Scripta Mater., 2003, vol. 48, pp. 1003-8.10.1016/S1359-6462(02)00591-2 ↗
29. J.W. Christian and S. Mahajan: Prog. Mater. Sci., 1995, vol. 39, pp. 1-157.10.1016/0079-6425(94)00007-7 ↗
30. Q. Ma, B. Li, W.R. Whittington, A.L. Oppedal, P.T. Wang and M.F. Horstemeyer: Acta Mater., 2014, vol. 67, pp. 102-15.10.1016/j.actamat.2013.12.025 ↗
31. Q. Ma, B. Li, A.L. Oppedal, W.R. Whittington, S.J. Horstemeyer, E.B. Marin, P.T. Wang and M.F. Horstemeyer: Mater. Sci. Eng. A, 2013, vol. 559, pp. 314-8.10.1016/j.msea.2012.08.104 ↗
32. Q. Ma, B. Li, Z. Mcclelland and S.J. Horstemeyer: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 4480-5.10.1007/s11661-013-1948-8 ↗
33. S.S. Vagarali and T.G. Langdon: Acta Metall., 1981, vol. 29, pp. 1969-82.10.1016/0001-6160(81)90034-1 ↗
34. S.S. Vagarali and T.G. Langdon: Acta Metall., 1982, vol. 30, pp. 1157-70.10.1016/0001-6160(82)90009-8 ↗
35. W.B. Hutchinson and M.R. Barnett: Scripta Mater., 2010, vol. 63, pp. 737-40.10.1016/j.scriptamat.2010.05.047 ↗
36. M.R. Barnett, Z. Keshavar and X. Ma: Metall. Mater. Trans. A, 2006, vol. 37, pp. 2283-93.10.1007/BF02586147 ↗
37. M.R. Barnett: Metall. Mater. Trans. A, 2003, vol 34, pp. 1799-806.10.1007/s11661-003-0146-5 ↗
38. A. Chapuis and J.H. Driver: Acta Mater., 2011, vol. 59, pp. 1986-94.10.1016/j.actamat.2010.11.064 ↗
39. C.J. Boehlert, Z. Chen, I. Gutiérrez-Urruti, J. Llorca and M.T. Pérez-Prado: Acta Mater., 2012, vol. 60, pp. 1889-904.10.1016/j.actamat.2011.10.025 ↗
40. B. Raeisinia and S.R. Agnew: Scripta Mater., 2010, vol. 63, pp. 731-6.10.1016/j.scriptamat.2010.03.054 ↗
41. A.H. Blake and C.H. Cáceres: Mater. Sci. Eng. A, 2008, vol. 483, pp. 161-3.10.1016/j.msea.2006.10.205 ↗
42. J.D. Robson, A.M. Twier, G.W. Lorimer and P. Rogers: Mater. Sci. Eng. A, 2011, vol. 528, pp. 7247-56.10.1016/j.msea.2011.05.075 ↗
43. T. Al-Samman and X. Li: Mater. Sci. Eng. A, 2011, vol. 528, pp. 3809-22.10.1016/j.msea.2011.01.080 ↗
44. C.J. Boehlert, Z. Chen, A. Chakkedath, A. Gutiérrez-Urrutia, J. Llorca, J. Bohlen, S. Yi, D. Letzig and M.T Pérez-Prado: Phil. Mag., 2013, vol. 93, pp. 598-617.10.1080/14786435.2012.725954 ↗
45. N.V. Dudamell, P. Hidalgo-Manrique, A. Chakkedath, Z. Chen, C.J. Boehlert, F. Gálvez, S. Yi, J. Bohlen, D. letzig and M.T. Pérez-Prado: Mater. Sci. Eng. A, 2013, vol. 583, pp. 220-31.10.1016/j.msea.2013.07.003 ↗
46. A. Chakkedath, J. Bohlen, S. Yi, D. Letzig, Z. Chen and C.J. Boehlert: Metall. Mater. Trans. A, 2014, vol. 45, pp. 3254-74.10.1007/s11661-013-2143-7 ↗
47. J. Bohlen, M.R. Nürnberg, J.W. Senn, D. Letzig and S.R. Agnew: Acta Mater., 2007, vol. 55, pp. 2101-12.10.1016/j.actamat.2006.11.013 ↗
48. A.J. Schwartz, M. Kumar, B.L. Adams, and D.P. Field, eds.: Electron Backscatter Diffraction in Materials Science, 2nd edn., Springer, New York, 2009, pp. 329–36.10.1007/978-0-387-88136-2 ↗
49. H. Li, D.E. Mason, T.R. Bieler, C.J. Boehlert and M.A. Crimp: Acta Mater., 2013, vol. 61, pp. 7555-67.10.1016/j.actamat.2013.08.042 ↗
50. H. Li, C.J. Boehlert, T.R. Bieler and M.A. Crimp: Metall. Mater. Trans. A, 2014, vol. 45, pp. 6053-66.10.1007/s11661-014-2576-7 ↗
51. H. Li, D.E. Mason, Y. Yang, T.R. Bieler, M.A, Crimp and C.J. Boehlert: Phil. Mag., 2013, vol. 93, pp. 2875-95.10.1080/14786435.2013.791752 ↗
52. G.E. Dieter: Mechanical Metallurgy, 3rd ed., McGraw-Hill Book Co., New York, USA, 1986.
53. B.A. Simkin, M.A. Crimp and T.R. Bieler: Scripta Mater., 2003, vol. 49, pp. 149-54.10.1016/S1359-6462(03)00216-1 ↗
54. A. Fallahi, D.E. Mason, D. Kumar, T.R. Bieler and M.A. Crimp: Mater. Sci. and Eng. A, 2006, vol. 432, pp. 281-91.10.1016/j.msea.2006.06.046 ↗
55. J.R. Seal, M.A. Crimp, T.R. Bieler and C.J. Boehlert: Mater. Sci. Eng. A, 2012, vol. 552, pp. 61-8.10.1016/j.msea.2012.04.114 ↗
56. T.R. Bieler, P. Eisenlohr, C. Zhang, H.J. Phukan and M.A. Crimp: Curr. Opin. Solid St. M., 2014, vol. 18, pp. 212-26.10.1016/j.cossms.2014.05.003 ↗