Influence of Stored Strain on Fabricating of Al/SiC Nanocomposite by Friction Stir Processing
Source abstract
Abstract
In this work, 1050 aluminum (Al) sheets were annealed and severely deformed by 1, 2, and 3 passes of constrained groove pressing process to obtain the various initial stored strain values of 0, 1.16, 2.32, and 3.48, respectively. Friction stir processing (FSP) was then applied using SiC nanoparticles to fabricate Al/SiC nanocomposite with approximately 1.5 vol pct reinforced particles. Microstructural examinations revealed that an increase in the initial stored strain of the base metal led to the formation of finer grain structure after 1 pass of FSP. The finer grain structure occurred in the stir zone where a sufficient amount of nanoparticles with a relatively proper distribution existed. However, the initial stored strain value had a contrary influence in the regions with low volume fraction of nanoparticles. In fact, more stored strain in the base metal provided more driving force for both nucleation and grain growth of newly recrystallized grains at the stir zone. Pinning effect of well-distributed nanoparticles could effectively retard grain growth leading to the formation of very fine grain structure. Also it was observed that the initial stored strain values did not have impressive rule in the microstructural evolutions at the stir zone during the second and third FSP passes signifying that all of the stored energy in the base metal would be released after 1 pass of FSP. The results obtained with microhardness measurement at the stir zone were fairly in agreement with those achieved by the microstructure assessments.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (58)
Show source-provided references
1. R. Bauri, D. Yadav, and G. Suhas: Mater. Sci. Eng. A, 2011, vol. 528, pp. 4732–39.10.1016/j.msea.2011.02.085 ↗
2. J. Guo, S. Amira, P. Gougeon, and X.-G. Chen: Mater. Charact., 2011, vol. 62, pp. 865–77.10.1016/j.matchar.2011.06.007 ↗
3. L. Ke, C. Huang, L. Xing, and K. Huang: J. Alloys Compd., 2010, vol. 503, pp. 494–99.10.1016/j.jallcom.2010.05.040 ↗
4. M.A. Moghaddas and S.F. Kashani-Bozorg: Mater. Sci. Eng. A, 2013, vol. 559, pp. 187–93.10.1016/j.msea.2012.08.073 ↗
5. C. Hu and T.N. Baker: J. Mater. Sci., 1995, vol. 30, pp. 891–97.10.1007/BF01178422 ↗
6. C. Hu and T. N.Baker: J. Mater. Sci., 1997, vol. 32, pp. 5047–51.10.1023/A:1018653030270 ↗
7. S.-H. Choo, S. Lee, and S.-J. Kwon: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1211–21.10.1007/s11661-999-0271-x ↗
8. K. Shin and S. Lee: Met. Mater. Int., 2003, vol. 9, pp. 549–53.10.1007/BF03027254 ↗
9. S.-H. Choo, S. Lee, and S.-J. Kwon: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 3131–41.10.1007/s11661-999-0224-4 ↗
10. M. Gui and S.B. Kang: Mater. Lett., 2000, vol. 46, pp. 296–302.10.1016/S0167-577X(00)00191-9 ↗
11. M. Gui, S.B. Kang, and K. Euh: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 2471–80.10.1007/s11661-005-0121-4 ↗
12. A.N. Attia: Mater. Des., 2001, vol. 22, pp. 459–66.10.1016/S0261-3069(00)00080-7 ↗
13. C.J. Hsu, C.Y. Chang, P.W. Kao, N.J. Ho, and C.P. Chang: Acta Mater., 2006, vol. 54, pp. 5241–49.10.1016/j.actamat.2006.06.054 ↗
14. M. Sharifitabar, A. Sarani, S. Khorshahian, and M. Shafiee Afarani: Mater. Des., 2011, vol. 32, pp. 4164–72.10.1016/j.matdes.2011.04.048 ↗
15. R.S. Mishra, Z.Y. Ma, and I. Charit: Mater. Sci. Eng. A, 2003, vol. 341, pp. 307–10.10.1016/S0921-5093(02)00199-5 ↗
16. H.S. Arora, H. Singh, and B.K. Dhindaw: Int. J. Adv. Manuf. Technol., 2011, vol. 61, pp. 1043–55.10.1007/s00170-011-3758-8 ↗
17. P. Asadi, M.K.B. Givi, K. Abrinia, M. Taherishargh, and R. Salekrostam: J. Mater. Eng. Perform., 2011, vol. 20, pp. 1554–62.10.1007/s11665-011-9855-x ↗
18. M. Barmouz, P. Asadi, M.K. Besharati Givi, and M. Taherishargh: Mater. Sci. Eng. A, 2011, vol. 528, pp. 1740–49.10.1016/j.msea.2010.11.006 ↗
19. M. Barmouz and M.K.B. Givi: Compos. A, 2011, vol. 42, pp. 1445–53.10.1016/j.compositesa.2011.06.010 ↗
20. G. Faraji and P. Asadi: Mater. Sci. Eng. A, 2011, vol. 528, pp. 2431–40.10.1016/j.msea.2010.11.065 ↗
21. C.J. Hsu, P.W. Kao, and N.J. Ho: Scripta Mater., 2005, vol. 53, pp. 341-45.10.1016/j.scriptamat.2005.04.006 ↗
22. I.S. Lee, P.W. Kao, and N.J. Ho: Intermetallics, 2008, vol. 16, pp. 1104–08.10.1016/j.intermet.2008.06.017 ↗
23. A. Shamsipur, S.F. Kashani-Bozorg, and A. Zarei-Hanzaki: Surf. Coat. Technol., 2011, vol. 206, pp. 1372–81.10.1016/j.surfcoat.2011.08.065 ↗
24. C.M. Hu, C.M. Lai, X.H. Du, N.J. Ho, and J.C. Huang: Scripta Mater., 2008, vol. 59, pp. 1163–66.10.1016/j.scriptamat.2008.06.040 ↗
25. J. Qu, H. Xu, Z. Feng, D.A. Frederick, L. An, and H. Heinrich: Wear, 2011, vol. 271, pp. 1940–45.10.1016/j.wear.2010.11.046 ↗
26. A. Shafiei-Zarghani, S.F. Kashani-Bozorg, and A.Z. Hanzaki: Wear, 2011, vol. 270, pp. 403–12.10.1016/j.wear.2010.12.002 ↗
27. B. Zahmatkesh and M.H. Enayati: Mater. Sci. Eng. A, 2010, vol. 527, pp. 6734–40.10.1016/j.msea.2010.07.024 ↗
28. Y. Mazaheri, F. Karimzadeh, and M.H. Enayati: J. Mater. Process. Technol., 2011, vol. 211, pp. 1614–19.10.1016/j.jmatprotec.2011.04.015 ↗
29. A. Dolatkhah, P. Golbabaei, M.K. Besharati Givi, and F. Molaiekiya: Mater. Des., 2012, vol. 37, pp. 458–64.10.1016/j.matdes.2011.09.035 ↗
30. W. Wang, Q.-y. Shi, P. Liu, H.-k. Li, and T. Li: J. Mater. Process. Technol., 2009, vol. 209, pp. 2099-2103.10.1016/j.jmatprotec.2008.05.001 ↗
31. R.Z. Valiev and T.G. Langdon: Prog. Mater. Sci., 2006, vol. 51, pp. 881–981.10.1016/j.pmatsci.2006.02.003 ↗
32. Y. Saito, N. Tsuji, H. Utsunomiya, T. Sakai, and R.G. Hong: Scripta Mater., 1998, vol. 39, pp. 1221–27.10.1016/S1359-6462(98)00302-9 ↗
33. M.S. Khorrami, M. Kazeminezhad, and A.H. Kokabi: Mater. Sci. Eng. A, 2012, vol. 543, pp. 243–48.10.1016/j.msea.2012.02.082 ↗
34. M. Sarkari Khorrami, M. Kazeminezhad, and A.H. Kokabi: Mater. Des., 2012, vol. 40, pp. 364–72.10.1016/j.matdes.2012.04.016 ↗
35. M. Sarkari Khorrami, M. Kazeminezhad, A.H. Kokabi: Mater. Sci. Eng. A, 2014, vol. 602, pp. 110-18.10.1016/j.msea.2014.02.067 ↗
36. Y. Sun, H. Fujii, Y. Takada, N. Tsuji, K. Nakata, and K. Nogi: Mater. Sci. Eng. A, 2009, vol. 527, pp. 317–21.10.1016/j.msea.2009.07.071 ↗
37. D.H. Shin, J. Park, Y. Kim, and K. Park: Mater. Sci. Eng. A, 2002, vol. 328, pp. 98–103.10.1016/S0921-5093(01)01665-3 ↗
38. E. Hosseini and M. Kazeminezhad: Mater. Des., 2011, vol. 32, pp. 487–94.10.1016/j.matdes.2010.08.033 ↗
39. M. Kazeminezhad and E. Hosseini: Mater. Des., 2010, vol. 31, pp. 94–103.10.1016/j.matdes.2009.07.008 ↗
40. J. Zrnik, T. Kovarikb, Z.Novya, and M. Cieslarc: Mater. Sci. Eng. A, 2009, vol. 503, pp. 126–29.10.1016/j.msea.2008.03.050 ↗
41. E. Hosseini and M. Kazeminezhad: Mater. Sci. Eng. A, 2009, vol. 526, pp. 219–24.10.1016/j.msea.2009.07.028 ↗
42. M.J. Starink, X.G. Qiao, J. Zhang, and N. Gao: Acta Mater., 2009, vol. 57, pp. 5796–5811.10.1016/j.actamat.2009.08.006 ↗
43. K. Colligan: Weld. J., 1999, vol. July, pp. 229s–37s.
44. J.A. Schneider and A.C. Nunes Jr.: Metall. Mater. Trans. B, 2004, vol. 35B, pp. 777–83.10.1007/s11663-004-0018-4 ↗
45. M. Guerra, C. Schmidt, J.C. McClure, L.E. Murr, and A.C. Nunes: Mater. Charact., 2002, vol. 49, pp. 95–101.10.1016/S1044-5803(02)00362-5 ↗
46. M.N. Avettand-Fènoël, A. Simar, R. Shabadi, R. Taillard, and B. de Meester: 9th International Symposium on Friction Stir Welding, May 2012, Huntsville, United States.
47. M. Salehi, H. Farnoush, and J.A. Mohandesi: Mater. Des., 2014, vol. 63, pp. 419–26.10.1016/j.matdes.2014.06.013 ↗
48. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng. R, 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
49. M. Azizieh, A.H. Kokabi, and P. Abachi: Mater. Des., 2011, vol. 32, pp. 2034–41.10.1016/j.matdes.2010.11.055 ↗
50. T.R. McNelley, S. Swaminathan, and J.Q. Su: Scripta Mater., 2008, vol. 58, pp. 349–54.10.1016/j.scriptamat.2007.09.064 ↗
51. M.N. Avettand-Fènoël, A. Simar, R. Shabadi, R. Taillard, and B. de Meester: Mater. Des., 2014, vol. 60, pp. 343–57.10.1016/j.matdes.2014.04.012 ↗
52. J.F. Guo, J. Liu, C.N. Sun, S. Maleksaeedi, G. Bi, M.J. Tan, and J. Wei: Mater. Sci. Eng. A, 2014, vol. 602, pp. 143–49.10.1016/j.msea.2014.02.022 ↗
53. R.D. Doherty, M.E. Kassner, D.A. Hughes, W.E. King, F.J. Humphreys, T.R. McNelley, J.J. Jonas, H.J. McQueen, D.J. Jensen, and A.D. Rollett: Mater. Sci. Eng. A, 1997, vol. 238, pp. 219–74.10.1016/S0921-5093(97)00424-3 ↗
54. C.I. Chang, C.J. Lee, and J.C. Huang: Scripta Mater., 2004, vol. 51, pp. 509–14.10.1016/j.scriptamat.2004.05.043 ↗
55. L.P. Troeger and E.A. Starke Jr: Mater. Sci. Eng. A, 2000, vol. 293, pp. 19–29.10.1016/S0921-5093(00)01235-1 ↗
56. M. Amirizad, A.H. Kokabi, M.A. Gharacheh, R. Sarrafi, B. Shalchi, and M. Azizieh: Mater. Lett., 2006, vol. 60, pp. 565–68.10.1016/j.matlet.2005.09.035 ↗
57. D.-H. Choi, Y.-I. Kim, D.-U. Kim, and S.-B. Jung: Trans. Nonferrous Met. Soc. China, 2012, vol. 22, pp. 614–18.10.1016/S1003-6326(12)61773-7 ↗
58. D.J. Lloyd: Int. Mater. Rev., 1994, vol. 39, pp. 1–24.10.1179/imr.1994.39.1.1 ↗