Laser Wire Deposition of Thick Ti-6Al-4V Buildups: Heat Transfer Model, Microstructure, and Mechanical Properties Evaluations
Source abstract
Abstract
This paper investigates the effect of depositing thick laser wire Ti-6Al-4V samples on the developed microstructure and subsequent mechanical properties. First, a thermal model is proposed to get a better understanding on the typical thermal cycles that the material has undergone. It is followed by a discussion on the typical structural features that developed in the as-built condition and following three post deposition heat treatments. A stress relief cycle did not substantially affect the morphology of the developed α platelets. Annealing and HIP followed by aging favored the coarsening of the post-deposited microstructure. A strengthening in terms of hardness has been observed only after the stress relief heat treatment. Developed static tensile properties were globally below the wrought levels. Stress-relieved specimens developed the higher strengths, whereas the annealed or HIPed samples followed by aging were associated with a better elongation. Charpy impact properties were higher in the annealed or HIPed condition followed by aging when compared with the stress-relieved ones. No anisotropy in the impact toughness properties was observed. The annealed and aged samples and the HIPed and aged samples produced overall very similar results showing that HIP is not required for enhance materials properties of laser wire deposition applications.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (60)
Show source-provided references
1. G. Lütjering and J.C. Williams: Titanium, 2nd ed., Springer, Verlag Berlin Heidelberg, 2007, pp. 1-52.
2. F.H.S. Froes, M.N. Gungor and M.A. Imam: JOM, 2007, vol. 59, pp. 28-31.10.1007/s11837-007-0074-8 ↗
3. I. Gibson, D.W. Rosen and B. Stucker: Additive Manufacturing Technologies, Springer, New York, 2015, pp. 1-62.10.1007/978-1-4939-2113-3 ↗
4. C.K. Chua and K.F. Leong: 3D Printing and Additive Manufacturing Principles and Applications, 4th ed., World Scientific, Singapore, 2014.10.1142/9008 ↗
5. E. Brandl, F. Palm, V. Michailov, B. Viehweger and C. Leyens: Mater. Des., 2011, vol. 32, pp. 4665-75.10.1016/j.matdes.2011.06.062 ↗
6. E. Brandl, B. Baufeld, C. Leyens and R. Gault: Physcs. Proc., 2010, vol. 5, pp. 595-606.10.1016/j.phpro.2010.08.087 ↗
7. P. Åkerfeldt, M.-L. Antti and R. Pederson: Mater. Sci. Eng. A, 2016, vol. 674, pp. 428-37.10.1016/j.msea.2016.07.038 ↗
8. B. Baufeld, E. Brandl and O. Van der Biest: J. Mater. Process. Tech., 2011, vol. 211, pp. 1146-58.10.1016/j.jmatprotec.2011.01.018 ↗
9. E. Brandl and D. Greitemeier: Mater. Lett., 2012, vol. 81, pp. 84-87.10.1016/j.matlet.2012.04.116 ↗
10. E. Brandl, A. Schoberth and C. Leyens: Mater. Sci. Eng. A, 2012, vol. 532, pp. 295-307.10.1016/j.msea.2011.10.095 ↗
11. E. Brandl, V. Michailov, B. Viehweger and C. Leyens: Surf. Coat. Tech., 2011, vol. 206, pp. 1120-29.10.1016/j.surfcoat.2011.07.095 ↗
12. E. Brandl, V. Michailov, B. Viehweger and C. Leyens: Surf. Coat. Tech., 2011, vol. 206, pp. 1130-41.10.1016/j.surfcoat.2011.07.094 ↗
13. S.H. Mok, G. Bi, J. Folkes and I. Pashby: Surf. Coat. Tech., 2008, vol. 202, pp. 3933-39.10.1016/j.surfcoat.2008.02.008 ↗
14. S.H. Mok, G. Bi, J. Folkes, I. Pashby and J. Segal: Surf. Coat. Tech., 2008, vol. 202, pp. 4613-19.10.1016/j.surfcoat.2008.03.028 ↗
15. N. Chekir, Y. Tian, R. Gauvin, N. Brodusch, JJ Sixsmith and M. Brochu: Mater. Sci. Eng. A, 2018, vol: 724, pp. 335-47.10.1016/j.msea.2018.03.101 ↗
16. S.M. Thompson, L. Bian, N. Shamsaei and A. Yadollahi: Addit. Manuf., 2015, vol. 8, pp. 36-62.10.1016/j.addma.2015.07.001 ↗
17. C. Qiu, G.A. Ravi, C. Dance, A. Ranson, S. Dilworth and M.M. Attallah: J. Alloy. Compd., 2015, vol. 629, pp. 351-61.10.1016/j.jallcom.2014.12.234 ↗
18. B. Baufeld: J. Eng. Manuf., 2011, vol. 226, pp. 126-36.10.1177/0954405411403669 ↗
19. J.S. Keist and T.A. Palmer: Mater. Des., 2016, vol.106, pp. 482-94.10.1016/j.matdes.2016.05.045 ↗
20. S. Wolff, T. Lee, E. Faierson, K. Ehmann and J. Cao: J. Manuf. Process., 2016, vol. 24, pp. 397-405.10.1016/j.jmapro.2016.06.020 ↗
21. B.E. Carroll, T.A. Palmer and A.M. Beese: Acta Mater., 2015, vol. 87, pp. 309-20.10.1016/j.actamat.2014.12.054 ↗
22. N. Shamsaei, A. Yadollahi, L. Bian and S.M. Thompson: Addit. Manuf., 2015, vol. 8, pp. 12-35.10.1016/j.addma.2015.07.002 ↗
23. E.R. Denlinger, J. Irwin and P. Michaleris: J. Manuf. Sci. Eng., 2014, vol. 136, 061007.10.1115/1.4028669 ↗
24. Q. Yang, P. Zhang, L. Cheng, Z. Min, M. Chyu and A.C. To: Addit. Manuf., 2016, vol. 12, pp. 169-177.10.1016/j.addma.2016.06.012 ↗
25. M. Labudovic, D. Hu and R. Kovacevic: J. Mater. Sci., 2003, vol. 38, pp. 35-49.10.1023/A:1021153513925 ↗
26. Dr. Amimul Ahsan: Convection and Conduction Heat Transfer, InTech, Shanghai, 2011, pp. 315-40.10.5772/1041 ↗
27. J.C. Heigel, P. Michaleris and E.W. Reutzel: Addit. Manuf., 2015, vol. 5, pp. 9-19.10.1016/j.addma.2014.10.003 ↗
28. G. Mi, Y. Wei, X. Zhan, C. Gu and F. Yu: J. Mater. Process. Tech., 2014, vol. 214, pp. 2434-43.10.1016/j.jmatprotec.2014.05.011 ↗
29. R. Rai, J.W. Elmer, T.A. Palmer and T. DebRoy: J. Phys. D Appl. Phys., 2007, vol. 40, pp. 5753-66.10.1088/0022-3727/40/18/037 ↗
30. M.J. Donachie: Titanium: A Technical Guide, 2nd ed., ASM international, Materials Park, OH, 2000, pp. 13-24.10.31399/asm.tb.ttg2.t61120013 ↗
31. I. Katzarov, S. Malinov and W. Sha: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 1027-40.10.1007/s11661-002-0204-4 ↗
32. S.M. Kelly and S.L. Kampe: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 1869-79.10.1007/s11661-004-0095-7 ↗
33. G.P. Dinda, L. Song and J. Mazumder: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 2914-22.10.1007/s11661-008-9634-y ↗
34. J.J. Lin, Y.H. Lv, Y.X. Liu, B.S. Xu, Z. Sun, Z.G. Li and Y.X. Wu: Mater. Des., 2016, vol. 102, pp. 30-40.10.1016/j.matdes.2016.04.018 ↗
35. J.J. Lin, Y.H. Lv, Y.X. Liu, Z. Sun, K.B. Wang, Z.G. Li, Y.X. Wu and B.S. Xu: J. Mech. Behav. Biomed. Mater., 2017, vol. 69, pp. 19-29.10.1016/j.jmbbm.2016.12.015 ↗
36. N. Chekir, Y. Tian, JJ Sixsmith and M. Brochu: Mater. Sci. Eng. A, 2018, vol. 724; pp. 376-84.10.1016/j.msea.2018.03.100 ↗
37. N. Stefansson, S.L. Semiatin and D. Eylon: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3527-34.10.1007/s11661-002-0340-x ↗
38. N. Stefansson and S.L. Semiatin: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 691-98.10.1007/s11661-003-0103-3 ↗
39. S.L. Semiatin, B.C. Kirby and G.A. Salishchev: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 2809-19.10.1007/s11661-004-0228-z ↗
40. T. Ahmed and H.J. Rack: Mater. Sci. Eng. A, 1998, vol. 243, pp. 206-11.10.1016/S0921-5093(97)00802-2 ↗
41. Y. Zhai, H. Galarraga and D.A. Lados: Eng. Fail. Anal., 2016, vol. 69, pp. 3-14.10.1016/j.engfailanal.2016.05.036 ↗
42. J. Yu, M. Rombouts, G. Maes and F. Motmans: Physcs. Proc., 2012, vol. 39, pp. 416-24.10.1016/j.phpro.2012.10.056 ↗
43. J. Alcisto, A. Enriquez, H. Garcia, S. Hinkson, T. Steelman, E. Silverman, P. Valdovino, H. Gigerenzer, J. Foyos, J. Ogren, J. Dorey, K. Karg, T. McDonald and O.S. Es-Said: J. Mater. Eng. Perform., 2011, vol. 20, pp. 203-12.10.1007/s11665-010-9670-9 ↗
44. Q. Zhang, J. Chen, Z. Qi, X. Lin, H. Tan and W. Huang: Metall. Mater. Trans. A, 2018, vol. 49A, pp. 3651-62.10.1007/s11661-018-4695-z ↗
45. F. Wang, S. Williams, P. Colegrove and A.A. Antonysamy: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 968-77.10.1007/s11661-012-1444-6 ↗
46. M. Simonelli, Y.Y. Tse and C. Tuck: Mater. Sci. Eng. A, 2014, vol. 616, pp. 1-11.10.1016/j.msea.2014.07.086 ↗
47. C. Buirette, J. Huez, N. Gey, A. Vassel and E. Andrieu: Mater. Sci. Eng. A, 2014, vol. 618, pp. 546-57.10.1016/j.msea.2014.09.048 ↗
48. B. Baufeld, O. Van der Biest and S. Dillien: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 1917-27.10.1007/s11661-010-0255-x ↗
49. D. Bhattacharyya, G.B. Viswanathan and H.L. Frase: Acta Mater., 2007, vol. 55, pp. 6765-78.10.1016/j.actamat.2007.08.029 ↗
50. M. Niinomi, T. Kobayashi and N. Sasaki: Mater. Sci. Eng., 1998, vol. 100, pp. 45-55.10.1016/0025-5416(88)90238-8 ↗
51. J.M. Gómez de Salazar, A. Ureña and J.G. Carrión: Scripta Mater., 1996, vol. 35, pp. 479-84.10.1016/1359-6462(96)00177-7 ↗
52. M. Balasubramanian, V. Jayabalan and V. Balasubramanian: Mater. Lett., 2008, vol. 62, pp. 1102-06.10.1016/j.matlet.2007.07.065 ↗
53. D.-G. Lee, S. Lee and Y. Lee: Mater. Sci. Eng. A, 2008, vol. 486, pp. 19-26.10.1016/j.msea.2007.08.053 ↗
54. T.J. Ma, W.-Y. Li and S.Y. Yang: Mater. Des., 2009, vol. 30, pp. 2128-32.10.1016/j.matdes.2008.08.029 ↗
55. W. Zhou and K.G. Chew: Mater. Sci. Eng. A, 2003, vol. 347, pp. 180-85.10.1016/S0921-5093(02)00596-8 ↗
56. K.P. Rao, K. Angamuthu and P.B. Srinivasan: J. Mater. Process. Tech., 2008, vol. 199, pp. 185-92.10.1016/j.jmatprotec.2007.08.001 ↗
57. L.W. Meyer, L. Krüger, K. Sommer, T. Halle and M. Hockauf: Mech. Time-Depend. Mat., 2008, vol. 12, pp. 237-47.10.1007/s11043-008-9060-y ↗
58. T. Akahori, M. Niinomi and K.-I. Fukunaga: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1937-48.10.1007/s11661-000-0221-0 ↗
59. M.-W. Wu and P.-H. Lai: Mater. Sci. Eng. A, 2016, vol. 658, pp. 429-38.10.1016/j.msea.2016.02.023 ↗
60. E. Yasa, J. Deckers, J.-P. Kruth, M. Rombouts and J. Luyten: Virtual Phys. Prototyp., 2010, vol. 5, pp. 89-98.10.1080/17452751003703894 ↗