journal article·2018-11

Mechanical and Microstructural Characterization of AF955 (UNS N09955) Nickel-Based Superalloy After Different Heat Treatments

Andrea Serafini, Giuliano Angella, Carlo Malara, Maria Francesca Brunella

Publisher page

Abstract

The mechanical and strain-hardening behaviors of the new AF955 nickel-based superalloy were investigated through two different heat treatments. The first consisted of a solubilization with a subsequent precipitation heat treatment at 746 °C for 4 hours, while the second included an additional precipitation treatment at 621 °C for 8 hours, which further increased the AF955 yield stress by about 15 pct and the ultimate stress by about 9 pct. However, through analyzing the true stress and true strain flow curves, the Considére's stresses of AF955 after the heat treatments were similar and the strain-hardening behaviors at high stresses were surprisingly comparable. The AF955 microstructures were observed after the two different heat treatments through transmission electron microscopy. The dimensions and volume fractions of the strengthening ?? and ?? particles were quantified through the imaging analysis technique, finding that there were only ?? particles in AF955 with heat treatment at 746 °C, while with the additional heat treatment at 621 °C, there was a higher total volume fraction of the ?? + ?? phases. The microstructure quantification allowed modeling of the different yield behaviors of the alloy after the heat treatments through the Orowan model for nondeformable particles and the weak coupled dislocation (WCD) and strong coupled dislocation models for deformable particles. The WCD model for deformable particles described the yield behaviors of AF955 very well after both heat treatments. Moreover, the deformability of the ?? and ?? particles also explained the comparable strain-hardening behaviors at high stresses of AF955 after the two different heat treatments. Although mechanical properties are correctly assumed to be key parameters for classifying materials, the analysis of true stress and true strain flow curves always should be performed to properly rationalize the mechanical behaviors of metallic alloys.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. R.B. Bhavsar, A. Collins, and S. Silverman: Superalloys 718, 625, 706 Var. Deriv., 2001, pp. 47–55.10.7449/2001/Superalloys_2001_47_55 ↗
2. B.D. Craig, and L. Smith: Nickel Institute Technical Series No 10073, 2011, pp. 1–12.
3. 3. P.R. Rhodes: Corrosion, 2001, vol. 57, pp. 923–66.10.5006/1.3290320 ↗
4. 4. L. Popoola, A. Grema, G. Latinwo, B. Gutti, and A. Balogun: Int. J. Ind. Chem., 2013, vol. 4, pp. 1–15.10.1186/2228-5547-4-35 ↗
5. R.W. Evans, J.D. Parker, and B. Wilshire: in Recent Advances in Creep and Fracture of Engineering Materials and Structure, B. Wilshire and D.R.J. Oven, eds., Pineridge Press, United Kingdom, 1982.
6. B.F. Dyson, and M. McLean: in Creep in Structures, S. Murakami and N. Ohno, eds., Kluwer Academic Publishers, South Holland, The Netherlands, 2001.
7. M. Maldini, V. Lupinc, and G. Angella: Kov. Mater.-Metallic Mater., 2004, vol. 42, pp. 21–30.
8. 8. M. Maldini, G. Angella, and V. Lupinc: Mater. Sci. Eng. A, 2007, vol. 462, p. 463.10.1016/j.msea.2005.11.084 ↗
9. 9. G. Angella, R. Donnini, D. Ripamonti, and M. Maldini: Mater. Sci. Forum, 2017, vol. 879, pp. 448–53.10.4028/www.scientific.net/MSF.879.448 ↗
10. API Standard 6ACRA—First Edition, Age-hardened nickel-based alloys for oil and gas drilling and production equipment, API Publishing Services, Washington, DC.
11. NACE MR0175/ISO 15156-3, Petroleum and Natural Gas Industries—Material for Use in H2S-Containing Environments in Oil and Gas Production—Part 3: Cracking-Resistant CRAs (Corrosion Resistant Alloys) and Other Alloys, 2009 (Second Edition), NACE International, Houston, TX.
12. L. Foroni, C. Malara, R. Montani, and S. Gregory: Paper presented at CORROSION 2015, NACE International, Houston, TX, 2015.
13. L. Foroni, C. Malara, R. Montani, and S. Gregory: Paper presented at CORROSION 2016, NACE International, Vancouver, BC, Canada, 2016.
14. 14. A. Devaux, L. Nazé, R. Molins, A. Pineau, A. Organista, J.Y. Guédou, J.F. Uginet, and P. Héritier: Mater. Sci. Eng. A, 2008, vol. 486, pp. 117–22.10.1016/j.msea.2007.08.046 ↗
15. 15. M. Sundararaman, P. Mukhopadhyay, and S. Banerjee: Metall. Trans. A, 1992, vol. 23A, pp. 2015–28.10.1007/BF02647549 ↗
16. A. Strondl, R. Fischer, G. Frommeyer, and A. Schneider: Mater. Sci. Eng. A, 2008, vol. 480, 138–147.10.1016/j.msea.2007.07.012 ↗
17. 17. G.A. Rao, M. Kumar, M. Srinivas, and D.S. Sarma: Mater. Sci. Eng. A, 2003, vol. 355, pp. 114–25.10.1016/S0921-5093(03)00079-0 ↗
18. 18. B. Dubiel, A. Kruk, E. Stepniowska, G. Cempura, D. Geiger, P. Formanek, J. Hernandez, P. Midgley, and A. Czyrska-Filemonowicz: J. Microsc., 2009, vol. 236, pp. 149–57.10.1111/j.1365-2818.2009.03283.x ↗
19. 19. K. Kulawik, P.A. Buffat, A. Kruk, A.M. Wusatowska-Sarnek, and A. Czyrska-Filemonowicz: Mater. Charact., 2015, vol. 100, pp. 74–80.10.1016/j.matchar.2014.12.012 ↗
20. 20. P. Sarosi, G. Viswanathan, D. Whitis, and M. Mills: Superalloys 2004,TMS Publications, Warrendale, PA, 2004, pp. 989–96.10.7449/2004/Superalloys_2004_989_996 ↗
21. AMS 2750E (2012–07), Pyrometry, SAE International, PA.
22. ASTM E8/E8M-15a, Standard Test Method for Tension Testing of Metallic Material, ASTM International, West Conshohocken, PA.
23. 23. P.M. Kelly, A. Jostsons, R.G. Blake, and J.G. Napier: Phys. Status Solidi, 1975, vol. 31, pp. 771–80.10.1002/pssa.2210310251 ↗
24. 24. C.A. Schneider, W.S. Rasband, and K.W. Eliceiri: Nat. Methods, 2012, vol. 9, pp. 671–75.10.1038/nmeth.2089 ↗
25. 25. U.F. Kocks: J. Eng. Mater. Technol., 1976, vol. 98, pp. 76–85.10.1115/1.3443340 ↗
26. 26. U.F. Kocks and H. Mecking: Acta Metall., 1985, vol. 29, pp. 1865–75.
27. 27. U.F. Kocks and H. Mecking: Progr. Mater. Sci., 2003, vol. 48, pp. 171–273.10.1016/S0079-6425(02)00003-8 ↗
28. 28. G. Angella, B.P. Wynne, W.M. Rainforth, and J.H. Beynon: Mater. Sci. Eng. A, 2008, vol. 475, pp. 257–67.10.1016/j.msea.2007.05.089 ↗
29. 29. G. Angella: Mater. Sci. Eng. A, 2012, vol. 532, pp. 381–91.10.1016/j.msea.2011.10.108 ↗
30. 30. G. Angella, R. Donnini, M. Maldini, and D. Ripamonti: Mater. Sci. Eng. A, 2014, vol. 594, pp. 381–88.10.1016/j.msea.2013.11.088 ↗
31. 31. M. Sundararaman, R. Kishore, and P. Mukhopadhyay: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 653–56.10.1007/BF02651609 ↗
32. 32. K.V.U. Praveen, G.V.S. Sastry, and V. Singh: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 65–78.10.1007/s11661-007-9375-3 ↗
33. 33. Shaik Khaja, K.K. Mehta, R. Veera Babu, S. Sri Rama Devi, and A.K. Singh: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 1140–53.10.1007/s11661-014-2706-2 ↗
34. Y. Estrin: in Unified Constitutive Laws of Plastic Deformation, A.S. Krausz and K. Krausz, eds., Elsevier, New York, 1996, pp. 69–106.10.1016/B978-012425970-6/50003-5 ↗
35. 35. A.J. Ardell: Metall. Trans., 1985, vol. 16, pp. 2131–65.10.1007/BF02670416 ↗
36. 36. R. Schnitzer, S. Zinner, and H. Leitner: Scripta Mater., 2010, vol. 62, pp. 286–89.10.1016/j.scriptamat.2009.11.020 ↗
37. 37. R.C. Reed: The Superalloys, Fundamentals and Applications, Cambridge University Press, Cambridge, United Kingdom, 2006.10.1017/CBO9780511541285 ↗
38. M.R. Ahmadi, M. Rath, E. Povoden-Karadeniz, S. Primig, T. Wojcik, A. Danninger, M. Stockinger, and E. Kozeschnik: Model. Simul. Mater. Sci. Eng., 2017, vol. 25, Art. No. 055005.10.1088/1361-651X/aa6f54 ↗
39. 39. B. Sonderegger and E. Kozeschnik: Scripta Mater., 2012, vol. 66, pp. 52–55.10.1016/j.scriptamat.2011.10.003 ↗
40. 40. R. Sharghi-Moshtaghin and S. Asgar: J. Mater. Proc. Technol., 2004, vol. 147, pp. 343–50.10.1016/j.jmatprotec.2004.01.006 ↗
41. A. deVaucorbeil, W.J. Poole, and C.W. Sinclair: Mater. Sci. Eng. A, 2013, vol. 582, pp. 147–54.10.1016/j.msea.2013.06.032 ↗
42. 42. Yung-Ta Chen, An-Chou Yeh, Ming-YenLi, and Shih-Ming Kuo: Mater. Design, 2017, vol. 119, pp. 235–43.10.1016/j.matdes.2017.01.069 ↗
43. 43. H.F. Merrick: Metall. Trans.,1974, vol. 5, pp. 891–97.10.1007/BF02643144 ↗
44. 44. M. Sundararaman, P. Mukhopadhyay, and S. Banerjee: Acta Metall., 1988, vol. 36, pp. 847–64.10.1016/0001-6160(88)90139-3 ↗
45. 45. Y. Mishima, S. Ochiai, N. Hamao, M. Yodogawa, and T. Suzuki: Trans. Jpn. Inst. Mater., 1986, vol. 27, pp. 656–64.10.2320/matertrans1960.27.656 ↗
46. 46. H.A. Roth, C.L. Davis, and R.C. Thompson: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 1329–35.10.1007/s11661-997-0268-2 ↗
47. 47. G. Lütjering and S. Weissman: Acta Metall., 1970, vol. 18, pp. 785–95.10.1016/0001-6160(70)90043-X ↗
48. 48. P.J. Gregson and H.M. Flower: Acta Metall., 1985, vol. 33, pp. 527–37.10.1016/0001-6160(85)90095-1 ↗
49. F.J. Humphreys, and M. Hatherly: Recrystallisation and Related Phenomena, 2nd ed., Elsevier, Boston, 2004.