Transient-Liquid-Phase Bonding of H230 Ni-Based Alloy Using Ni-P Interlayer: Microstructure and Mechanical Properties
Source abstract
Abstract
Transient-liquid-phase bonding using Ni-P as an interlayer has been developed for H230 Ni-Cr-W solid-solution-strengthened Ni-based alloy. Two process parameters—composition of the interlayer and bonding time—have been varied to optimize the mechanical properties. H230 has been bonded into two sets of stacks (set I and II) for 8 and 4 hours using Ni-12P and Ni-6P interlayer, respectively, (wt pct) at 1423 K (1150 °C) and 12.7 MPa. The microstructure of both the stacks has three distinct regions—the joint centerline which showed the presence of pores, an isothermally solidified zone (ISZ) which did not have any carbide precipitates and base H230. Transmission electron microscopy and atom probe tomography showed a uniform microstructure, and an absence of any deleterious phases at the joint and in ISZ. Set I and set II had a yield strength of 76 and 86 pct of that of the H230 sheet, tested at 1023 K (750 °C). The measured elongation at fracture was negligible, but the fracture surfaces revealed a ductile cup-and-cone-type fracture occurring through the ISZ/joint region. Examination of broken tensile samples revealed that the plastic strain was constrained to within one joint region through which fracture occurred.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Advanced Materials Characterization Techniques · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. R.J. Allam: NET Power’s CO2 cycle: the breakthrough that CCS needs, www.modernpowersystems.com/features/, 2013.
2. R. Dennis: EPRI International Conference on Corrosion in Power Plants, Palo Alto, CA, USA, 2015, pp. 2-136-132-153.
3. B.K. Paul: Micro Energy and Chemical Systems (MECS) and Multiscale Fabrication, Springer, Berlin, 2006, pp. 299–355.10.1007/3-540-29339-6_14 ↗
4. [4] L.M. Pike, S.K. Srivastava: Adv. Mat. Res., 2011, vol.278, pp. 327-332.10.4028/www.scientific.net/AMR.278.327 ↗
5. [5] H.M. Tawancy, D.L. Klarstrom, M.F. Rothman: JOM, 1984, vol.36, pp. 58-62.10.1007/BF03338564 ↗
6. D. Klarstrom, H. Tawancy, D. Fluck, and M. Rothman: ASME 1984 International Gas Turbine Conference and Exhibit, American Society of Mechanical Engineers, 1984, pp. V005T11A003–V005T11A003.
7. [7] M.A. Arafin, M. Medraj, D.P. Turner, P. Bocher: Mater. Chem. Phys., 2007, vol.106, pp. 109-119.10.1016/j.matchemphys.2007.05.049 ↗
8. [8] M.A. Arafin, M. Medraj, D.P. Turner, P. Bocher: Mater. Sci. Eng., A, 2007, vol.447, pp. 125-133.10.1016/j.msea.2006.10.045 ↗
9. [9] A. Egbewande, C. Chukwukaeme, O. Ojo: Mater. Charact., 2008, vol.59, pp. 1051-1058.10.1016/j.matchar.2007.08.023 ↗
10. [10] A. Ekrami, S. Moeinifar, A.H. Kokabi: Mater. Sci. Eng., A, 2007, vol.456, pp. 93-98.10.1016/j.msea.2006.12.044 ↗
11. [11] O.A. Idowu, N.L. Richards, M.C. Chaturvedi: Mater. Sci. Eng., A, 2005, vol.397, pp. 98-112.10.1016/j.msea.2005.01.055 ↗
12. Y. Natsume, K. Ohsasa, and T. Narita: Mater. Trans., JIM, 2003, vol.44, pp. 819–823.10.2320/matertrans.44.819 ↗
13. [13] W. Gale, E. Wallach: Metall. Trans. A, 1991, vol.22, pp. 2451-2457.10.1007/BF02665011 ↗
14. D.M. Jacobson and G. Humpston: Principles of Brazing, ASM International, 2005.10.31399/asm.tb.pb.9781627083515 ↗
15. [15] F. Jalilian, M. Jahazi, R.A.L. Drew: Mater. Sci. Eng., A, 2006, vol.423, pp. 269-281.10.1016/j.msea.2006.02.030 ↗
16. [16] M. Pouranvari, A. Ekrami, A.H. Kokabi: J. Alloys Compd., 2009, vol.469, pp. 270-275.10.1016/j.jallcom.2008.01.101 ↗
17. [17] G.O. Cook, C.D. Sorensen: J Mater. Sci., 2011, vol.46, pp. 5305-5323.10.1007/s10853-011-5561-1 ↗
18. [18] A. Ghoneim, O. Ojo: Mater. Charact., 2011, vol.62, pp. 1-7.10.1016/j.matchar.2010.09.011 ↗
19. [19] O.A. Ojo, N.L. Richards, M.C. Chaturvedi: Sci. Technol. Weld. Joining, 2004, vol.9, pp. 532-540.10.1179/174329304X8702 ↗
20. [20] R. Bakhtiari, A. Ekrami: Mater. Des., 2012, vol.40, pp. 130-137.10.1016/j.matdes.2012.03.036 ↗
21. [21] T.C. Illingworth, I.O. Golosnoy, T.W. Clyne: Mater. Sci. Eng., A, 2007, vol.445-446, pp. 493-500.10.1016/j.msea.2006.09.090 ↗
22. [22] N.S. Bosco, F.W. Zok: Acta Mater., 2004, vol.52, pp. 2965-2972.10.1016/j.actamat.2004.02.043 ↗
23. [23] N.S. Bosco, F.W. Zok: Acta Mater., 2005, vol.53, pp. 2019-2027.10.1016/j.actamat.2005.01.013 ↗
24. [24] M. Tseng, D. Williams, K. Soni, R. Levi-Setti: J Mater. Sci., 1999, vol.34, pp. 5187-5197.10.1023/A:1004707812417 ↗
25. M. Kapoor, Ö. Doğan, K. Rozman, J. Hawk, A. Wilson, T. L’Estrange, V. Narayanan: Proceedings of the 5th International Symposium on Supercritical CO 2 Power Cycles, San Antonio, Texas, 2016.
26. [26] J.-O. Andersson, T. Helander, L. Höglund, P. Shi, B. Sundman: Calphad, 2002, vol.26, pp. 273-312.10.1016/S0364-5916(02)00037-8 ↗
27. [27] E.E. Underwood: Quantitative stereology, Addison-Wesley, Massachusetts, 1970.
28. [28] ASTM standard E8, 2013 “Standard test methods for tension testing of metallic materials” ASTM International, West Conshohocken, PA.
29. [29] H. Chuang, J. Yu, M. Kuo, H. Tong, C. Kao: Scripta Mater., 2012, vol.66, pp. 171-174.10.1016/j.scriptamat.2011.10.032 ↗
30. [30] A. Lis, C. Leinenbach: J. Electron. Mater., 2015, vol.44, pp. 4576-4588.10.1007/s11664-015-3982-3 ↗
31. [31] A. Sakamoto: Weld. J, 1989, vol.69, pp. 63-71.
32. M.K. Miller: Atom Probe Tomography: Analysis at the Atomic Level, Springer, 2012.
33. [33] D.J. Larson, T.J. Prosa, R.M. Ulfig, B.P. Geiser, T.F. Kelly: Local electrode atom probe tomography, Springer Science, New York, USA, 2013.10.1007/978-1-4614-8721-0 ↗
34. W. Cao and R. Kennedy: Superalloys 718, 625, 706 and Various Derivatives, 1994, pp. 463–77.10.7449/1994/Superalloys_1994_463_477 ↗
35. [35] M. Wang, J. Du, Q. Deng, Z. Tian, J. Zhu: Mater. Sci. Eng., A, 2015, vol.626, pp. 382-389.10.1016/j.msea.2014.12.094 ↗
36. J. Goldstein, D.E. Newbury, P. Echlin, D.C. Joy, A.D. Romig Jr, C.E. Lyman, C. Fiori, and E. Lifshin: Scanning electron microscopy and X-ray microanalysis: a text for biologists, materials scientists, and geologists, Springer, 2012.
37. T.H. Courtney: Mechanical Behavior of Materials, Waveland Press, Long Grove, 2005.