Near-Surface Microstructure on Twin-Roll Cast 8906 Aluminum Alloy
Source abstract
Abstract
The microstructure of the near-surface region of twin-roll cast foil stock 8906 AlFeSi alloy has been investigated. It was revealed that a near-surface layer with microstructure differing from that of the underlying bulk alloy was generated due to severe surface shear strain during twin-roll casting. Scanning and transmission electron microscopy showed that the near-surface layer consists of nano-sized grains with diameters varying in the range of 50 to 600 nm. Energy dispersive X-ray spectroscopy revealed that grain boundaries within the near-surface layer were decorated by aluminum oxide particles and carbon-containing lubricant inclusions. Preferential precipitation of a high population density of cubic α-AlFeSi dispersoids, of 30 to 150 nm diameter, was observed within the near-surface layer. The near-surface layer was associated with shingles on the twin-roll cast alloy surface and the maximum layer thickness of approximately 6 µm was observed at the shingles. Other areas of the surface were either free of the near-surface layer or had a thinner near-surface layer.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. R. Cook, P.G. Grocock, P.M. Thomas, D.V. Edmonds, and J.D. Hunt: J. Mater. Process. Technol., 1995, vol. 55, pp. 76–84.10.1016/0924-0136(95)01788-7 ↗
2. E.F. Emley: Int. Met. Rev., 1976, vol. 21, pp. 75–115.10.1179/imr.1976.21.1.75 ↗
3. D.V. Edmonds, J.D. Hunt, D.J. Monaghan, X. Yang, M. Yun, D.J. Browne, R. Cook, and P.M. Thomas: Proc. 4th Int. Symp. Extr., Refin. Fabr. Light Met., Ottawa, Canada, 1991, pp. 257–71.10.1016/B978-0-08-041444-7.50027-5 ↗
4. M. Yun, D.J. Monagham, X. Yang, J. Jang, D.V. Edmonds, J.D. Hunt, R. Cook, and P.M. Thomas: Cast Met., 1991, vol. 4, pp. 108–11.10.1080/09534962.1991.11819065 ↗
5. M. Fishkis and J.C. Lin: Wear, 1997, vol. 206, pp. 156–70.10.1016/S0043-1648(96)07480-7 ↗
6. H. Leth-Olsen, J.H. Nordlien, and K. Nisancioglu: Corros. Sci., 1998, vol. 40, pp. 2051–63.10.1016/S0010-938X(98)00094-8 ↗
7. G. Plassart and M. Aucouturier: Proc. 2nd Int. Conf. Alum. Surf. Sci. Technol., Manchester, UK, 2000, pp. 29–35.
8. G.M. Scamans, A. Afseth, G.E. Thompson, and X. Zhou: Proc. 2nd Int. Conf. Alum. Surf. Sci. Technol., Manchester, UK, 2000, pp. 9–16.
9. G.M. Scamans, M.F. Frolish, W.M. Rainforth, Z. Zhou, Y. Liu, X. Zhou, and G.E. Thompson: Surf. Interface Anal., 2010, vol. 42, pp. 175–79.10.1002/sia.3204 ↗
10. Y. Liu, M.F. Frolish, W.M. Rainforth, X. Zhou, G.E. Thompson, G.M. Scamans, and J.A. Hunter: Surf. Interface Anal., 2010, vol. 42, pp. 180–84.10.1002/sia.3135 ↗
11. X. Zhou, Y. Liu, G.E. Thompson, G. Scamans, P. Skeldon, and J. Hunter: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 1373–85.10.1007/s11661-010-0538-2 ↗
12. K. Li, X. Zhou, G.E. Thompson, J.A. Hunter, and Y. Yuan: Mater. Sci. Forum, 2013, vol. 765, pp. 358–62.10.4028/www.scientific.net/MSF.765.358 ↗
13. B. Liu and X. Zhou: Mater. Sci. Forum, 2014, vol. 794–796, pp. 217–22.10.4028/www.scientific.net/MSF.794-796.217 ↗
14. Y. Liu, A. Laurino, T. Hashimoto, X. Zhou, P. Skeldon, G.E. Thompson, G.M. Scamans, C. Blanc, W.M. Rainforth, and M.F. Frolish: Surf. Interface Anal., 2010, vol. 42, pp. 185–88.10.1002/sia.3136 ↗
15. Y. Liu, X. Zhou, G.E. Thompson, T. Hashimoto, G.M. Scamans, and A. Afseth: Acta Mater., 2007, vol. 55, pp. 353–60.10.1016/j.actamat.2006.08.025 ↗
16. Premendra, J.H. Chen, F.D. Tichelaar, H. Terryn, J.H.W. deWit, and L. Katgerman: Surf. Coat. Technol., 2007, vol. 201, pp. 4561–70.10.1016/j.surfcoat.2006.09.090 ↗
17. X. Zhou, G.E. Thompson, and G.M. Scamans: Corros. Sci., 2003, vol. 45, pp. 1767–77.10.1016/S0010-938X(03)00003-9 ↗
18. A. Afseth, J.H. Nordlien, G.M. Scamans, and K. Nisancioglu: Corros. Sci., 2001, vol. 43, pp. 2093–2109.10.1016/S0010-938X(01)00014-2 ↗
19. K. Nisancioglu, J.H. Nordlien, A. Afseth, and G.M. Scamans: Mater. Sci. Forum, 2000, vol. 331–337, pp. 111–26.10.4028/www.scientific.net/MSF.331-337.111 ↗
20. I. Lindseth: PhD Thesis, Norwegian University of Science and Technology, Trondheim, 1999.
21. H. Leth-Olsen and K. Nisancioglu: Corros. Sci., 1998, vol. 40, pp. 1179–94.10.1016/S0010-938X(98)00026-2 ↗
22. H. Leth-Olsen, A. Afseth, and K. Nisancioglu: Corros. Sci., 1998, vol. 40, pp. 1195–1214.10.1016/S0010-938X(98)00025-0 ↗
23. J. Wang, X. Zhou, G.E. Thompson, J.A. Hunter, and Y. Yuan: Mater. Charact., 2015, vol. 99, pp. 109–17.10.1016/j.matchar.2014.11.011 ↗
24. C. Gras, M. Meredith, and J.D. Hunt: J. Mater. Process. Technol., 2005, vol. 169, pp. 156–63.10.1016/j.jmatprotec.2005.03.034 ↗
25. C. Gras, M. Meredith, K. Gatenby, and J.D. Hunt: Mater. Sci. Forum, 2002, vol. 396–402, pp. 89–94.10.4028/www.scientific.net/MSF.396-402.89 ↗
26. N.A. Belov, D.G. Eskin and A.A. Axenov: Multicomponent Phase Diagrams: Applications for Commercial Aluminum Alloys, Elsevier, Amsterdam, 2005, pp. 1–10.10.1016/B978-008044537-3/50001-9 ↗
27. C.M. Allen, K.A.Q. O’Reilly, B. Cantor, and P.V. Evans: Prog. Mater. Sci., 1998, vol. 43, pp. 89–170.10.1016/S0079-6425(98)00003-6 ↗
28. P. Skjerpe: Matall. Mater. Trans. A, 1987, vol. 18A, pp. 189–200.10.1007/BF02825700 ↗
29. L.F. Mondolfo: Aluminum Alloys: Structure and Properties, Butterworth, London, 1976.
30. A.D. Howells, G. Hoellrigl, A. Danielou, and F. Lauret: U.S. Patent, US 20110165015 A1, 2011.
31. H.W.L. Philips: Equilibrium Diagrams of Aluminum Alloy Systems, The Aluminum Development Association, London, 1961, pp. 91–96.
32. I. Yarita, L. Mallett, and E.H. Lee: Proc. 1st Int. Conf. Technol. Plast., Tokyo, Japan, 1984, pp. 1126–31.
33. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, 2nd ed., Elsevier, Amsterdam, 2004.
34. H.R. Le, M.P.F. Sutcliffe, P.Z. Wang, and G.T. Burstein: Acta Mater., 2004, vol. 52, pp. 911–20.10.1016/j.actamat.2003.10.027 ↗
35. M.F. Frolish, M. Krzyzanowski, W.M. Rainforth, and J.H. Beynon: J. Mater. Process. Technol., 2006, vol. 177, pp. 36–40.10.1016/j.jmatprotec.2006.03.224 ↗
36. M. Krzyzanowski, J.H. Beynon, M.F. Frolish, and S. Clowe: Mater. Sci. Forum, 2007, vol. 539–543, pp. 2461–66.10.4028/www.scientific.net/MSF.539-543.2461 ↗
37. M. Krzyzanowski and W.M. Rainforth: Ironmak. Steelmak., 2010, vol. 37, pp. 276–82.10.1179/030192310X12646889255663 ↗
38. M.F. Frolish, J.C. Walker, C. Jiao, W.M. Rainforth, and J.H. Beynon: Tribol. Int., 2005, vol. 38, pp. 1050–58.10.1016/j.triboint.2005.07.021 ↗
39. G.M. Scamans, A. Afseth, G.E. Thompson, and X. Zhou: Proc. 3rd Int. Conf. Alum. Surf. Sci. Technol., Bonn, Germany, 2003, pp. 90–94.
40. A. Afseth, J.H. Nordlien, G.M. Scamans, and K. Nisancioglu: Corros. Sci., 2001, vol. 43, pp. 2359–77.10.1016/S0010-938X(01)00019-1 ↗
41. A. Afseth, J. H. Nordlien, G. M. Scamans, and K. Nisancioglu: Corros. Sci., 2002, vol. 44, pp. 2529–42.10.1016/S0010-938X(02)00029-X ↗
42. A. Afseth, J. H. Nordlien, G. M. Scamans, and K. Nisancioglu: Corros. Sci., 2002, vol. 44, pp. 2491–2506.10.1016/S0010-938X(02)00036-7 ↗
43. Y.Birol: J. Mater. Process. Technol., 2009, vol. 209, pp. 506–10.10.1016/j.jmatprotec.2008.02.019 ↗