journal article·2012-06

Influence of Mode of Metal Transfer on Microstructure and Mechanical Properties of Gas Metal Arc-Welded Modified Ferritic Stainless Steel

Manidipto Mukherjee, Tapan Kumar Pal

Publisher page

Abstract

This article describes in detail the effect of the modes of metal transfer on the microstructure and mechanical properties of gas metal arc-welded modified ferritic stainless steel (SSP 409M) sheets (as received) of 4 mm thickness. The welded joints were prepared under three modes of metal transfer, i.e., short-circuit (SC), spray (S), transfer, and mix (M) mode transfer using two different austenitic filler wires (308L and 316L) and shielding gas composition of Ar + 5 pct CO2. The welded joints were evaluated by means of microstructural, hardness, notched tensile strength, Charpy impact toughness, and high cycle fatigue. The dependence of weld metal microstructure on modes of metal transfer and filler wires has been determined by dilution calculation, WRC-1992 diagram, Creq/Nieq ratio, stacking fault energy (SFE), optical microscopy (OM), and transmission electron microscopy (TEM). It was observed that the microstructure as well as the tensile, Charpy impact, and high cycle fatigue of weld metal is significantly affected by the mode of metal transfer and filler wire used. However, the heat-affected zone (HAZ) is affected only by the modes of metal transfer. The results have been correlated with the microstructures of weld and HAZ developed under different modes of metal transfer.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. A.M. Meyers and M. du Toit: Welding Research Supplement, 2001, vol. 80, p. 275.
2. C.S. Cleiton, P.F. Jesualdo, and C.M. Helio: Mater. Charact., 2008, vol. 59, p. 528.10.1016/j.matchar.2007.03.011 ↗
3. M. du Toit, G.T. van Rooyen, and D. Smith: IIW Doc IX-2213-06, IIW Doc IX-H-640-06. http://137.215.9.22/bitstream/handle/2263/6020/IX-2213-06.pdf?sequence=1.
4. M.L. Greef and M. du Toit: Weld. J., 2006, vol. 85, pp. 243-s–251-s.
5. P. Moore: Australasian Weld J., 1997, vol. 42, pp. 22–24.
6. D.N. Hawkins, J. Beech, and S. Valtierra-Gallardo: Sheffield, 1988, pp. 199–203.10.3109/01443618809012283 ↗
7. K. Shanmugam, A.K. Lakshminarayanan, and V. Balasubramanian: J. Mater. Sci. Tech., 2009, vol. 25, no. 2, pp. 181–86.
8. D.J. Kotecki: Weld. J., 2005, vol. 84, pp. 14–16.
9. T.G. Gooch and T.G. Davey: Proc. Inaugural International Conf., Johannesburg, South Africa, 1984, pp. 209–29.
10. J.C. Villafuerte and H.W. Kerr: Weld. J., 1990, vol. 69, p. 1-s.
11. J.J. Eckenrod and C.W. Kovach: American Society for Testing and Materials, ASTM, New York, NY, 1980, pp. 273–91.
12. R.J. Castro and J.J. de Cadenet: Welding Metallurgy of Stainless and Heat Resisting Steels, Cambridge University Press, London, UK, 1968.
13. E. Folkard: Welding Metallurgy of Stainless Steels, Springer-Verlag, New York, NY, 1984.
14. R. Thomas and R.L. Apps: American Society of Testing and Materials, ASTM, New York, NY, 1980, pp. 161–83.
15. J.J. Lowke: J. Phys. D: Appl. Phys., 2009, vol. 42, no. 135204, pp. 1–7.
16. M.C. Balmforth and J.C. Lippold: Weld. J., 1988, vol. 77, pp. 1s–7s.
17. J.C. Lippold: EWI Research Brief B9101, Columbus, OH, 1991.
18. D.J. Kotecki: Weld. J., 1997, vol. 76, pp. 24s–37s.
19. D.J. Kotecki: Weld. J., 2000, vol. 79, pp. 346s–54s.
20. R.H. Kaltenhauser: Metals Engineering Quarterly, 1971, vol. 1, pp. 41–47.
21. J. Lefevre, R. Tricot, and R. Castro: Rev. Metall., 1973, vol. 70, p. 259.10.1051/metal/197370040259 ↗
22. P.K. Ghosh, K. Devakumaran, and A.K. Pramanick: Weld. J., 2010, vol. 89, pp. 43s–53s.
23. N.H. Pryds and X. Huang: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 3155–66.10.1007/s11661-000-0095-1 ↗
24. J.C. Lippold and D.J. Kotecki: Welding Metallurgy and Weldability of Stainless Steels, 1st ed., Wiley, New York, NY, 2005, pp. 43–44.
25. S. Allain, J.P. Chateau, O. Bouaziz, S. Migot, and N. Guelton: Mater. Sci. Eng. A, 2004, vol. 158, pp. 387–89.
26. C.G. Rhodes and A.W. Thompson: Metall. Trans. A, 1977, vol. 8A, pp. 1901–06.10.1007/BF02646563 ↗
27. V. Seetharaman and P.J. Krishnan: Mater. Sci., 1981, vol. 16, pp. 523–30.10.1007/BF00738646 ↗
28. S.S.M. Tavares, J.M. Neto, M.R. Silva, I.F. Vasconcelos, and H.F.G. Abreu: Mater. Charact., 2008, vol. 59, pp. 901–04.10.1016/j.matchar.2007.07.007 ↗
29. S.A. David, J.M. Vitek, and T.L. Hebble: Weld. J., 1987, vol. 66, pp. 289s–300s.
30. J. Charlas: Proc. Conf. on Application of Stainless Steels’92, Stockholm, Jerncontoret, 1992, pp. 1108–1121.
31. G. Fourlaris and T. Gladman: Suppl. J. Phys., 1997, vol. 7, pp. C5-423–28.
32. J.A. Venables: Phil. Mag., 1962, vol. 7, pp. 35–44.10.1080/14786436208201856 ↗
33. D. Goodchild, W.T. Roberts, and D.V. Wilson: Acta Metall., 1970, vol. 18, pp. 1137–45.10.1016/0001-6160(70)90104-5 ↗
34. R. Lagneborg: Acta Metall., 1964, vol. 12, pp. 823–43.10.1016/0001-6160(64)90176-2 ↗
35. J.W. Brooks, M.H. Loretto, and R.E. Smallman: Acta Metall., 1979, vol. 27, pp. 1829–38.10.1016/0001-6160(79)90073-7 ↗
36. G.L. Leone and H.W. Kerr: Weld. J., 1982, pp. 13s–21s.
37. H. Zheng, X. Ye, L. Jiang, B. Wang, Z. Liu, and G. Wang: Mater. Des., 2010, vol. 31, p. 4836.10.1016/j.matdes.2010.05.054 ↗
38. K. Nishimoto: J. Jpn Weld. Soc., 1991, vol. 60, no. 8, pp. 15–19.10.2207/qjjws1943.60.637 ↗
39. L.I. Yajiang, Z. Yonglan, S. Bin, and W. Juan: Bull. Mater. Sci., 2002, vol. 25, pp. 361–66.10.1007/BF02708010 ↗
40. D.H. Kah and D.W. Dickinson: Weld. J., 1981, vol. 60, p. 135s.
41. A.K. Lakshminarayanan, K. Shanmugam, and V. Balasubramanian: J. Iron Steel Res. Int., 2009, vol. 16, pp. 66–72.10.1016/S1006-706X(10)60013-1 ↗
42. T.G. Gooch and B.J. Ginn: Report from the Cooperative Research Program for Research Members Only, The Welding Institute, Cambridge, UK, 1988, pp. 3–30.6.
43. S. Govin, G.R. Chanani, and S.D. Antolovich: Metall. Trans., 1974, vol. 5, p. 217.10.1007/BF02642945 ↗
44. G. Baudry and A. Pineau: Mater. Sci. Eng., 1977, vol. 28, pp. 229–42.10.1016/0025-5416(77)90176-8 ↗
45. S.G.S. Raman and K.A. Padmanabhan: Mater. Sci. Technol., 1994, vol. 10, pp. 614–20.10.1179/mst.1994.10.7.614 ↗