A Comparison of Residual Stress Development in Inertia Friction Welded Fine Grain and Coarse Grain Nickel-Base Superalloy
Source abstract
Abstract
The effect of the base material microstructure on the development of residual stresses across the weld line in inertia friction welds (IFWs) of high-strength nickel-base superalloy RR1000 was studied using neutron diffraction. A comparison was carried out between tubular IFW specimens generated from RR1000 heat treated below (fine grain (FG) structure) and above (coarse grain (CG) structure) the gamma'-solvus. Residual stresses were mapped in the as-welded (AW) condition and, after a postweld heat treatment (PWHT), optimized for maximum alloy strength. The highest tensile stresses were generally found in the hoop direction at the weld line near the inner diameter of the tubular-shaped specimens. A comparison between the residual stresses generated in FG and CG RR1000 suggests that the starting microstructure has little influence on the maximum residual stresses generated in the weld even though different levels of energy must be input to achieve a successful weld in each case. The residual stresses in the postweld heat treated samples were about 35 pct less than for the AW condition. Despite the fact that the high-temperature properties of the two parent microstructures are different, no significant differences in terms of stress relief were found between the FG and CG RR1000 IFWs. Since the actual weld microstructures of FG and CG RR1000 inertia welds are very similar, the results suggest that it is the weld microstructure and its associated high-temperature properties rather than the parent material that affects the overall weld stress distribution and its subsequent stress relief.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. C.T. Sims and W.C. Hagel: The Superalloys, Wiley, New York, NY, 1972.
2. R.F. Decker: Climax Symp., May 1969, Am. Mit. Climax Inc.
3. M. Preuss, J.W.L. Pang, P.J. Withers, and G.J. Baxter: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3215–25.10.1007/s11661-002-0307-y ↗
4. M.C. Hardy, B. Zirbel, G. Shen, and R. Shankar: Superalloy 2004, K.A. Green, T.M. Pollock, H. Harada, J.J. Schirra, and S. Walston, eds., TMS, Warrendale, pp. 83–90.10.7449/2004/Superalloys_2004_83_90 ↗
5. B. Grant, M. Preuss, P.J. Withers, G. Baxter, and M. Rowlson: Mater. Sci. Eng. A, 2009, vols. 513–514, pp. 366–75.10.1016/j.msea.2009.02.005 ↗
6. J.W.L. Pang, M. Preuss, P.J. Withers, G.J. Baxter, and C. Small: Mater. Sci. Eng. A, 2003, vol. 356 (1–2), pp. 405–13.10.1016/S0921-5093(03)00153-9 ↗
7. M. Preuss, J.W.L. Pang, P.J. Withers, and G.J. Baxter: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3227–34.10.1007/s11661-002-0308-x ↗
8. P.J. Withers and M. Preuss: ASM Handbook, vol. 22B, Modeling and Simulation: Processing of Metallic Materials, D.U. Furrer and S.L. Semiatin, eds., ASM INTERNATIONAL, Materials Park, OH, 2010.
9. B. Grant, M. Preuss, P.J. Withers, G. Baxter, and M. Rowlson: Mater. Sci. Eng. A, 2009, vols. 513–514, pp. 366–75.10.1016/j.msea.2009.02.005 ↗
10. M. Preuss, P.J. Withers, and G. Baxter: Mater. Sci. Eng. A, 2006, vol. 437 (1), pp. 38–45.10.1016/j.msea.2006.04.058 ↗
11. R.J. Mitchell, J.A. Lemsky, R. Ramanathan, H.Y. Li, K.M. Perkins, and L.D. Connor: Superalloy 2008, R. Reed et al., eds., TMS, Warrendale, pp. 347–56.10.7449/2008/Superalloys_2008_347_356 ↗
12. M.T. Hutchings, P.J. Withers, T.M. Holden, and Torben Lorentzen: Introduction to Characterization of Residual Stress by Neutron Diffraction, CRC Press, Boca Raton, FL, 2005.10.1201/9780203402818 ↗
13. P.J. Withers, M. Preuss, A. Steuwer, and J.W.L. Pang: J. Appl. Crystallogr., 2007, vol. 40, Part 5, pp. 891–904.10.1107/S0021889807030269 ↗
14. M.W. Johnson, L. Edwards, and P.J. Withers: Physica B, 1997, vol. 234, pp. 1141–43.10.1016/S0921-4526(97)89272-1 ↗
15. I.C. Noyan and J.B. Cohen: Residual Stress, Springer Verlag, New York, NY, 1987, p. 111.10.1007/978-1-4613-9570-6 ↗
16. T. Pirling, G. Bruno, and P.J. Withers: Mater. Sci. Eng. A, 2006, vol. 437, pp. 139–44.10.1016/j.msea.2006.04.083 ↗
17. J.A. Dann, M.R. Daymond, L. Edwards, J.A. James, and J.R. Santisteban: Physica B, 2004, vol. 350, pp. 511–14.10.1016/j.physb.2004.03.139 ↗
18. M. Hofmann, R. Schneider, G.A. Seidl, J. Rebelo-Kornmeier, R.C. Wimpory, U. Garbe, and H.G. Brokmeier: Physica B, 2006, vols. 385–386, p. 1035.10.1016/j.physb.2006.05.331 ↗
19. M. Karadge, B. Grant, G. Bruno, J. Santisteban, P.J. Withers, and M. Preuss: Mater. Sci. Forum, 2006, vols. 524–525, pp. 393–98.10.4028/www.scientific.net/MSF.524-525.393 ↗
20. R. Hill: The Mathematical Theory of Plasticity, Oxford Classic Series, Clarendon Press, Oxford, United Kingdom, 1998, p. 26.10.1093/oso/9780198503675.001.0001 ↗
21. R.A. Claudio, J.M. Silva, C.M. Branco, and J. Byrne: “Crack Propagation Behaviour of Shot Peened Components at Elevated Temperature,” 10 as Jornadas de Fractura, Univ. do Minho, Portugal, Fevereiro 2006 (available at http://ltodi.est.ips.pt/rclaudio/).10.1007/978-1-4020-6239-1_113 ↗