journal article·2015-08

Mechanical Properties Involved in the Micro-forming of Ultra-thin Stainless Steel Sheets

Cong-Hanh Pham, Sandrine Thuillier, Pierre-Yves Manach

Publisher page

Abstract

The objective of this paper is to characterize the mechanical behavior of an ultra-thin stainless steel, of 0.15-mm thickness, that is commonly used in the manufacturing of miniature connectors. The main focus is the relationship between some microstructural features, like grain size and surface roughness, and the macroscopic mechanical behavior investigated in uniaxial tension and simple shear. In tension, adaptations to the very small sheet thickness, in order to hold the specimen under the grips, are presented. Yield stress, initial elastic modulus, and evolution of the loading–unloading slope with plastic deformation were evaluated. Moreover, the kinematic contribution to the hardening was characterized by monotonic and cyclic simple shear test and reproduced by a mixed hardening law implemented in Abaqus finite element code. Then, the evolution of surface roughness with plastic strain, both in tension and simple shear, was analyzed. It was shown that in the case of an ultra-thin sheet, the stress levels, calculated either from an average thickness or when considering the effect of the surface roughness, exhibit a significant difference. Finally, the influence of surface roughness on the fracture of a tensile specimen was also investigated.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Advanced Surface Polishing Techniques · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. M. Geiger, M. Kleiner, R. Eckstein, N. Tiesler, U. Enge, CIRP Ann.: Manuf. Technol. 50, 445–62 (2001)10.1016/S0007-8506(07)62991-6 ↗
2. T. Connolley, P.E. Mchugh, M. Bruzzi, Fatigue Fract. Eng. Mater. Struct. 28, 1119–52 (2005)10.1111/j.1460-2695.2005.00951.x ↗
3. U. Engel, R. Eckstein, J. Mater. Process. Technol. 125–126, 35–44 (2002)10.1016/S0924-0136(02)00415-6 ↗
4. G.T. Gau, P.H. Chen, H. Gu, R.S. Lee, J. Mater. Process. Technol. 213, 376–82 (2013)10.1016/j.jmatprotec.2012.10.004 ↗
5. Nisshin Steel—Nisshin Steel Quality Products: Stainless Foil
6. E.M. Costache, N. Nanu, B. Chirita, G. Brabie, Int. J. Mech. Sci. 69, 125–140 (2013)10.1016/j.ijmecsci.2013.02.001 ↗
7. L. Peng, P. Hu, X. Lai, D. Mei, J. Ni, Mater. Des. 30, 783–790 (2009)10.1016/j.matdes.2008.05.074 ↗
8. Lester Metals LLC. Stainless Steel Products. http://www.lestermetals.com
9. Alufoil (EAFA) European Aluminum Foil Association. http://www.alufoil.org/facts.html
10. H. Hoffmann, S. Hong, CIRP Ann.: Manuf. Technol. 55, 263–266 (2006)10.1016/S0007-8506(07)60412-0 ↗
11. T. Furushima, H. Tsunezaki, K. Manabe, S. Alexsandrov, Int. J. Mach. Tool Manuf. 76, 34–48 (2014)10.1016/j.ijmachtools.2013.10.001 ↗
12. T. Furushima, H. Tsunezaki, K. Manabe, and S. Alexsandrov: 13th International Conference on Fracture, Beijing, China. 2013
13. S. Miyazaki, K. Shibata, H. Fujita, Acta Metall. 27, 855–862 (1979)10.1016/0001-6160(79)90120-2 ↗
14. F. Vollertsen, Micro Metal Forming (Springer, Berlin, 2013)10.1007/978-3-642-30916-8 ↗
15. N. Hansen, Acta Metall. 25, 863–869 (1977)10.1016/0001-6160(77)90171-7 ↗
16. J. Xu, B. Guo, D. Shan, M. Li, Z. Wang, Mater. Trans. 54, 984–989 (2013)10.2320/matertrans.M2013016 ↗
17. S. Mahabunphachai, M. Koç, Int. J. Mach. Tool Manuf. 48, 1014–1029 (2008)10.1016/j.ijmachtools.2008.01.006 ↗
18. P.J.M. Janssen, J.P.M. Hoefnagels, T.H. Keijser, M.G.D. Geers, J. Mech. Phys. Solids 56, 2687–2706 (2008)10.1016/j.jmps.2008.03.008 ↗
19. T. Furushima, H. Tsunezaki, T. Nakayama, K. Manabe, S. Alexsandrov, Key Eng. Mater. 554–557, 169–173 (2013)10.4028/www.scientific.net/KEM.554-557.169 ↗
20. O. Wouters, W.P. Vellinga, R. Van Tijum, J.T.M. Hosson, Acta Mater. 53, 4043–4050 (2005)10.1016/j.actamat.2005.05.007 ↗
21. H.A. Al-Qureshi, A.N. Klein, M.C. Fredel, J. Mater. Process. Technol. 170, 204–210 (2005)10.1016/j.jmatprotec.2005.04.116 ↗
22. W.L. Chan, M.W. Fu, J. Mater. Process. Technol. 212, 1501–1512 (2012)10.1016/j.jmatprotec.2012.02.013 ↗
23. J.G. Liu, M.W. Fu, J. Lu, W.L. Chan, Comput. Mater. Sci. 50, 2604–2614 (2011)10.1016/j.commatsci.2011.04.002 ↗
24. M. Klein, A. Hadrboletz, B. Weiss, G. Khatibi, Mater. Sci. Eng. A 319–321, 924–928 (2001)10.1016/S0921-5093(01)01043-7 ↗
25. T. Mizuno, H. Mulk, Wear 198, 176–184 (1996)10.1016/0043-1648(96)06963-3 ↗
26. M.W. Fu, W.L. Chan, Mater. Des. 32, 4738–4746 (2011)10.1016/j.matdes.2011.06.039 ↗
27. I. Ragai, D. Lazim, J.A. Nemes, J. Mater. Process. Technol. 166, 116–127 (2005)10.1016/j.jmatprotec.2004.08.007 ↗
28. S. Li, R.H. Wagoner, Int. J. Plast. 27, 1126–1144 (2011)10.1016/j.ijplas.2010.04.001 ↗
29. S. Thuillier, P.Y. Manach, Int. J. Plast. 25, 733–751 (2009)10.1016/j.ijplas.2008.07.002 ↗
30. C.H. Pham, S. Thuillier, P.Y. Manach, J. Mater. Process. Technol. 214, 844–855 (2014)10.1016/j.jmatprotec.2013.12.006 ↗
31. C.H. Pham, S. Thuillier, and P.Y. Manach: The 9th International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes, Melbourne, Australia, 2014, vol. 1567, pp. 422–427.10.1063/1.4850005 ↗
32. T.A. Kals, R. Eckstein, J. Mater. Process. Technol. 103, 95–101 (2000)10.1016/S0924-0136(00)00391-5 ↗
33. B.S. Katharine, A.E. David, A.C. Todd, Adv. Mater. Process. 166, 32–37 (2008)
34. ASTM E112–10. Standard test methods for determining average grain size. ASTM International, West Conshohocken 2010
35. S.A. Parasiz, R. VanBenthysen, B.L. Kinsey, J. Manuf. Sci. Eng. 132, 011–018 (2010)10.1115/1.4000943 ↗
36. G.T. Gau, C. Principe, J. Wang, J. Mater. Process. Technol. 184, 42–46 (2007)10.1016/j.jmatprotec.2006.11.003 ↗
37. C.J. Wang, D.B. Shan, J. Zhou, B. Guo, L.N. Sun, J. Mater. Process. Technol. 187–188, 256–269 (2007)10.1016/j.jmatprotec.2006.11.055 ↗
38. INSTRON Corporation. Instron Series 5500 Load Frames Including Series 5540, 5560, 5580. M10–14190-EN, Revision A 2007
39. G.T. Gau, C. Principe, M. Yu, J. Mater. Process. Technol. 191, 7–10 (2007)10.1016/j.jmatprotec.2007.03.035 ↗
40. ISO 6892–1:2009(E). Metallic Materials—Tensile Testing—Part 1: Method of Test at Room Temperature
41. ASTM E8/E8M. Standard test methods for tension testing of metallic materials. ASTM International, West Conshohocken 2009
42. Faerber J. Microscopie électronique à balayage, Microanalyse X par sonde électronique. Institut de Physique et Chimie des matériaux de Strabourg, Strasbourg, France 2004
43. H. Kim, C. Kim, F. Barlat, E. Pavlina, M.G. Lee, Mater. Sci. Eng. A 562, 161–171 (2013)10.1016/j.msea.2012.11.020 ↗
44. P.Y. Manach, N. Couty, Comput. Mech. 28, 17–25 (2002)10.1007/s004660100265 ↗
45. S. Bouvier, H. Haddadi, P. Levée, C. Teodosiu, J. Mater. Process. Technol. 172, 96–103 (2006)10.1016/j.jmatprotec.2005.09.003 ↗
46. L. Yang, L. Lu, Scripta Mater. 69, 242–245 (2013)10.1016/j.scriptamat.2013.04.009 ↗
47. S. Gallée, P.Y. Manach, S. Thuillier, Mater. Sci. Eng. A 466, 47–55 (2007)10.1016/j.msea.2007.02.054 ↗
48. Z. Tourki, H. Bargui, H. Sidhom, J. Mater. Process. Technol. 166, 330–336 (2005)10.1016/j.jmatprotec.2003.08.010 ↗
49. L. Joshua, T. Chester, M. Martin, Metall. Mater. Trans. A 37A, 147–161 (2006)
50. D.Y. Ryoo, N. Kang, C.Y. Kang, Mater. Sci. Eng. A 528, 2277–2281 (2011)10.1016/j.msea.2010.12.022 ↗
51. K. Yamaguchi, H. Adachi, N. Takakura, Met. Mater. Int. 4, 420–425 (1998)10.1007/BF03187802 ↗
52. M. Vrh, M. Halilovič, B. Štok, Exp. Mech. 51, 677–695 (2011)10.1007/s11340-010-9371-1 ↗
53. P.A. Eggertsen, K. Mattiasson, Int. J. Mech. Sci. 51, 547–563 (2009)10.1016/j.ijmecsci.2009.05.007 ↗
54. C.H. Pham, S. Thuillier, and P.Y. Manach: Steel Res. Int., 2015
55. M.A. Sutton, J.D. Helm, M.L. Boone, Int. J. Fract. 109, 285–301 (2001)10.1023/A:1011014917851 ↗
56. J. Bron, J. Besson, A. Pineau, Mater. Sci. Eng. A 380, 356–364 (2004)10.1016/j.msea.2004.04.008 ↗