journal article·2020-04Open access

Size Effects of Hardness and Strain Rate Sensitivity in Amorphous Silicon Measured by Nanoindentation

Dariusz M. Jarząbek, Michał Milczarek, Szymon Nosewicz, Piotr Bazarnik, Helmut Schift

Abstract

Abstract In this work, dynamic mechanical properties of amorphous silicon and scale effects were investigated by the means of nanoindentation. An amorphous silicon sample was prepared by plasma-enhanced chemical vapor deposition (PECVD). Next, two sets of the samples were investigated: as-deposited and annealed in 500 °C for 1 hour. A three-sided pyramidal diamond Berkovich’s indenter was used for the nanoindentation tests. In order to determine the strain rate sensitivity (SRS), indentations with different loading rates were performed: 0.1, 1, 10, 100 mN/min. Size effects were studied by application of maximum indentation loads in the range from 1 up to 5 mN (penetrating up to approximately one-third of the amorphous layer). The value of hardness was determined by the Oliver–Pharr method. An increase of hardness with decrease of the indentation depth was observed for both samples. Furthermore, the significant dependence of hardness on the strain rate has been reported. Finally, for the annealed samples at low strain rates a characteristic “elbow” during unloading was observed on the force-indentation depth curves. It could be attributed to the transformation of (β-Sn)-Si to the PI (pressure-induced) a-Si end phase.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Diamond and Carbon-based Materials Research · Advanced Surface Polishing Techniques · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (37)

Show source-provided references
1. R. M. R. Pinto, P. Brito, V. Chu, and J. P. Conde: Journal of Microelectromechanical Systems, 2019, vol. 28, pp. 390-400.10.1109/JMEMS.2019.2911666 ↗
2. J. Gaspar, A. Gualdino, B. Lemke, O. Paul, V. Chu, and J. P. Conde: J. Appl. Phys. 2012, 112, 024906.10.1063/1.4736548 ↗
3. B. Haberl, M. Guthrie, D. J. Sprouster, J. S. Williams, and J. E. Bradby: Journal of Applied Crystallography, 2013, vol. 46, pp. 758-768..10.1107/S0021889813010509 ↗
4. Y. B. Gerbig, C. A. Michaels, J. E. Bradby, B. Haberl, and R. F. Cook: Physical Review B, 2015, vol. 92, p. 214110.10.1103/PhysRevB.92.214110 ↗
5. M. Kiran, B. Haberl, J. S. Williams, and J. E. Bradby: Journal of Applied Physics, 2014, 115, 113511.10.1063/1.4869136 ↗
6. B. Haberl, A. C. Y. Liu, J. E. Bradby, S. Ruffell, J. S. Williams, and P. Munroe: Phys. Rev. B, 2009, 79, 155209.10.1103/PhysRevB.79.155209 ↗
7. B. Haberl, J. E. Bradby, M. V. Swain, J. S. Williams, and P. Munroe: Applied Physics Letters, 2004, vol. 85, pp. 5559-5561.10.1063/1.1832757 ↗
8. Z. Wu, J. Thou, W. Chen, J. Shen, C. Lv, and Y. Y. Qi: Ceramics International, 2015, vol. 41, pp. 11632-11636.10.1016/j.ceramint.2015.05.123 ↗
9. Z. W. Chen and N. Brandon: Ceramics International, 2016, vol. 42, pp. 8316-8324.10.1016/j.ceramint.2016.02.045 ↗
10. D. Naujoks et al.: Acta Materialia, 2017, vol. 138, pp. 100-110.10.1016/j.actamat.2017.07.037 ↗
11. S. Kauffmann-Weiss, S. Hahn, C. Weigelt, L. Schultz, M. F. X. Wagner, and S. Fahler: Acta Materialia, 2017, vol. 132, pp. 255-263.10.1016/j.actamat.2017.04.049 ↗
12. J. E. Bradby, J. S. Williams, J. Wong-Leung, M. V. Swain, and P. Munroe: Journal of Materials Research, 2001, vol. 16, pp. 1500-1507.10.1557/JMR.2001.0209 ↗
13. S. Wong et al.: Journal of Applied Physics, 2019, vol. 126, p. 105901.10.1063/1.5108751 ↗
14. J. I. Jang, M. J. Lance, S. Q. Wen, T. Y. Tsui, and G. M. Pharr: Acta Materialia, 2005, vol. 53, pp. 1759-1770.10.1016/j.actamat.2004.12.025 ↗
15. T. Juliano, Y. Gogotsi, and V. Domnich: Journal of Materials Research, 2003, vol. 18, pp. 1192-1201.10.1557/JMR.2003.0164 ↗
16. Y. M. Wei, Z. G. Lu, K. H. Hu, X. Y. Li, and P. J. Li: Ceramics International, 2018, vol. 44, pp. 11702-11710.10.1016/j.ceramint.2018.03.247 ↗
17. D. Ghosh, M. Banda, J. E. John, and D. A. Terrones: Scripta Materialia, 2018, vol. 154, pp. 236-240.10.1016/j.scriptamat.2018.06.006 ↗
18. Q. Wei: Journal of Materials Science, 2007, vol. 42, pp. 1709-1727.10.1007/s10853-006-0700-9 ↗
19. J. Fornell et al.: Acta Materialia, 2010, vol. 58, pp. 6256-6266.10.1016/j.actamat.2010.07.047 ↗
20. C. Liu, V. Roddatis, P. Kenesei, and R. Maass: Acta Materialia, 2017, vol. 140, pp. 206-216.10.1016/j.actamat.2017.08.032 ↗
21. P. Y. Zhao, J. Li, J. Hwang, and Y. Z. Wang: Acta Materialia, 2017, vol. 134, pp. 104-115.10.1016/j.actamat.2017.05.057 ↗
22. J. L. Wang, L. X. Wu, X. Chen, W. J. Zhuo, and G. F. Wang: Sensors and Actuators a-Physical, 2018, vol. 276, pp. 11-16.10.1016/j.sna.2018.04.021 ↗
23. D. A. Antartis, R. N. Mott, and I. Chasiotis: Materials & Design, 2018, vol. 144, pp. 182-191.10.1016/j.matdes.2018.02.017 ↗
24. H. K. Malik, S. Juneja, and S. Kumar: Journal of Theoretical and Applied Physics, 2019, vol. 13, pp. 107-113. .10.1007/s40094-019-0325-4 ↗
25. A. Soman, U. Nsofor, U. Das, T. Y. Gu, and S. Hegedus: ACS Appl. Mater. Interfaces, 11, 16181-16190 (2019)10.1021/acsami.9b01686 ↗
26. M. Chmielewski et al.: International Journal of Refractory Metals & Hard Materials, 2016, vol. 59, pp. 78-86.10.1016/j.ijrmhm.2016.05.017 ↗
27. J. Nohava, N. X. Randall, and N. Conte: Journal of Materials Research, 2009, vol. 24, pp. 873-882.10.1557/jmr.2009.0114 ↗
28. Y. Liu, J. Hay, H. Wang, and X. Zhang: Scripta Materialia, 2014, vol. 77, pp. 5-8.10.1016/j.scriptamat.2013.12.022 ↗
29. D. Pan, A. Inoue, T. Sakurai, and M. W. Chen: Proceedings of the National Academy of Sciences of the United States of America, 2008, vol. 105, pp. 14769-14772.10.1073/pnas.0806051105 ↗
30. J. G. Swadener, E. P. George, and G. M. Pharr: Journal of the Mechanics and Physics of Solids, 2002, vol. 50, pp. 681-694.10.1016/S0022-5096(01)00103-X ↗
31. S. J. Bull, T. F. Page, and E. H. Yoffe: Philosophical Magazine Letters, 1989, vol. 59, pp. 281-288.10.1080/09500838908206356 ↗
32. D. E. Stegall and A. A. Elmustafa: Metallurgical and Materials Transactions a-Physical Metallurgy and Materials Science, 2018, vol. 49A, pp. 4649-4658.10.1007/s11661-018-4817-7 ↗
33. J. E. Bradby, J. S. Williams, J. Wong-Leung, M. V. Swain, and P. Munroe: Applied Physics Letters, 2000, vol. 77, pp. 3749-3751.10.1063/1.1332110 ↗
34. S. Saitoh, T. Sugii, H. Ishiwara, and S. Furukawa: Japanese Journal of Applied Physics, 1981, vol. 20, pp. L130-L132.10.1143/JJAP.20.L130 ↗
35. S. Roorda et al.: Physical Review B, 1991, vol. 44, pp. 3702-3725.10.1103/PhysRevB.44.3702 ↗
36. V. Maier, K. Durst, J. Mueller, B. Backes, H. W. Hoppel, and M. Goken: Journal of Materials Research, 2011, vol. 26, pp. 1421-1430.10.1557/jmr.2011.156 ↗
37. S. K. Bhuyan et al.: Mrs Communications, 2012, vol. 2, pp. 9-12.10.1557/mrc.2011.24 ↗