A Mechanical, Microstructural, and Damage Study of Various Tailor Hot Stamped Material Conditions Consisting of Martensite, Bainite, Ferrite, and Pearlite
Source abstract
Abstract
This paper examines the mechanical, microstructural, and damage characteristics of five different material conditions that were created using the tailored hot stamping process with in-die heating. The tailored material conditions, TMC1 to TMC5 (softest-hardest), were created using die temperatures ranging from 700 °C to 400 °C, respectively. The tensile strength (and total elongation) ranged from 615 MPa (0.24) for TMC1 to 1122 MPa (0.11) for TMC5. TMC3 and TMC4 exhibited intermediate strength levels, with almost no increase in total elongation relative to TMC5. FE-SEM microscopy was used to quantify the mixed-phase microstructures, which ranged in volume fractions of ferrite, pearlite, bainite, and martensite. High-resolution optical microscopy was used to quantify void accumulation and showed that the total void area fraction at ~ 0.60 thickness strain was low for TMC1 and TMC5 (~ 0.09 pct) and highest for TMC3 (0.31 pct). Damage modes were characterized and revealed that the poor damage behavior of TMC3 (martensite/bainite/ferrite composition) was a result of small martensitic grains forming at grain boundaries and grain boundary junctions, which facilitated void nucleation as shown by the highest measured void density for this particular material condition. The excellent ductility of TMC1 was a result of a large grained ferritic/pearlitic microstructure that was less susceptible to void nucleation and growth. Large titanium nitride (TiN) inclusions were observed in all of the tailored material conditions and it was shown that they noticeably contributed to the total void accumulation, specifically for the TMC3 and TMC4 material conditions.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (52)
Show source-provided references
1. [1] H. Karbasian and E. Tekkaya: J. Mater. Process. Tech., 2010, vol. 210, pp 2103–18.10.1016/j.jmatprotec.2010.07.019 ↗
2. [2] M. Maikranz-Valentin, U. Weidig, U. Schoof, H.H. Becker, and K. Steinhoff: Steel Res. Int., 2008, vol. 79, pp. 92-97.10.1002/srin.200806322 ↗
3. [3] M. Merklein, M. Wieland, M. Lechner, S. Bruschi, and A. Ghotti: J. Mater. Process. Tech., 2016, vol. 228, pp. 11-24.10.1016/j.jmatprotec.2015.09.023 ↗
4. [4] R. George, A. Bardelcik, and M.J. Worswick: J. Mater. Process. Tech., 2012, vol. 212, pp. 2386-99.10.1016/j.jmatprotec.2012.06.028 ↗
5. [5] B. Klein, S. Crichley, and K. Khang: Great Designs in Steel Seminar, Livonia, USA, 2015.
6. [6] A. Bardelcik, C. Salisbury, S. Winkler, M.J. Worswick, and M. Wells: Int. J. Impact Eng., 2010, vol. 37, pp. 694-702.10.1016/j.ijimpeng.2009.05.009 ↗
7. [7] A. Bardelcik, M.J. Worswick, S. Winkler, and M. Wells: Int. J. Impact Eng., 2012, vol. 50, 49-62.10.1016/j.ijimpeng.2012.06.007 ↗
8. [8] A. Barcellona and D. Palmeri: Metall. Mater. Trans. A., 2009, vol. 40, pp. 1160-74.10.1007/s11661-009-9790-8 ↗
9. [9] J. Min, J. Lin, Y. Min, and F. Li: Mater. Sci. Eng. A., 2012, vol. 550, pp. 375-87.10.1016/j.msea.2012.04.091 ↗
10. [10] A. Bardelcik, M.J. Worswick, and M. Wells: Mater. and Des., 2014, vol. 55, pp. 509-25.10.1016/j.matdes.2013.10.014 ↗
11. [11] S. Golling, R. Ostlund, and M. Oldenburg: J. Mater. Process. Tech., 2016, vol. 228, pp. 88-97.10.1016/j.jmatprotec.2015.07.007 ↗
12. [12] P. Srithananan, P. Kaewtatip, and V. Uthaisangsuk: Mat. Sci. Eng. A., 2016, vol. 667, pp. 61-76.10.1016/j.msea.2016.04.065 ↗
13. [13] B.T. Tang, Q.L. Wang, S. Bruschi, A. Ghiotti, and P.F. Bariani: J. Manuf. Sci. E-T ASME, 2014, vol. 136, 1-14.10.1115/1.4027816 ↗
14. [14] T.K. Eller, L. Greve, M. Andres, M. Medricky, V.T. Meinders, and A.H. van den Boogaard: J. Mater. Process. Tech., 2016, vol. 228, pp. 43-58.10.1016/j.jmatprotec.2015.09.036 ↗
15. [15] T.K. Eller, L. Greve, M. Andres, M. Medricky, A. Hatscher, V.T. Meinders, and A.H. van den Boogaard: J. Mater. Process. Tech., 2014, vol. 214, pp. 1211-27.10.1016/j.jmatprotec.2013.12.015 ↗
16. [16] D. Mohr and F. Ebnoether: Int. J. Solids Struct., 2009, vol. 46, pp. 3535-47.10.1016/j.ijsolstr.2009.05.011 ↗
17. [17] K. Omer, L. ten Kortenaar, C. Butcher, M.J. Worswick, S. Malcolm, and D. Detwiler: Int. J. Impact Eng., 2017, vol. 103, pp. 12-28.10.1016/j.ijimpeng.2017.01.003 ↗
18. Y. Prajogo: MASc Thesis, University of Waterloo, 2015.
19. K. Omer, R. George, A. Bardelcik, M.J. Worswick, S. Malcolm, and D. Detwiler: Int. J. Mater. Form., 2018, vol. 11(1), pp. 149–64.10.1007/s12289-017-1338-7 ↗
20. ArcelorMittal – Usibor® 1500-AS CCT diagram (personal communication), 2009.
21. [21] R. Smerd, S. Winkler, C. Salisbury, M. Worswick, D. Lloyd, and M. Finn: Int. J. Impact Eng., 2005, vol. 32, pp. 541-60.10.1016/j.ijimpeng.2005.04.013 ↗
22. [22] G. Krauss: Mat. Sci. Eng. A., 1999, vol. A273-275, pp. 40-57.10.1016/S0921-5093(99)00288-9 ↗
23. T.N Baker: Mater. Sci. Technol. 2009, vol. 25, pp. 1083-10710.1179/174328409X453253 ↗
24. [24] Y. Li and T.N. Baker: Mat. Sci. and Tech., 2010, vol. 26, pp. 1029-40.10.1179/026708309X12512744154360 ↗
25. [25] N. Huda, A.R.H. Midawi, J. Gianetto, R. Lazor, and A.P. Gerlich: Mat. Sci. Eng. A., 2016, vol. 662, pp. 481-91.10.1016/j.msea.2016.03.095 ↗
26. [26] H.C. Chen and G.H. Cheng: J. Mater. Sci, 1989, vol. 24, pp. 1991-94.10.1007/BF02385411 ↗
27. [27] H.K.D.H. Bhadeshia and D.V. Edmonds: Met. Sci., 1983, vol. 17, pp. 411-19.10.1179/030634583790420600 ↗
28. [28] M.X. Zhang and P.M. Kelly: Mater. Char., 1998, vol. 40, 159-68.10.1016/S1044-5803(98)00005-9 ↗
29. [29] K. Banjerjee: Int. J. Metall. Eng., 2013, vol. 2 (1), pp. 100-10.
30. [30] H.K.D.H. Bhadeshia and J.W. Christian: Metall. Mater. Trans. A., 1990, vol. 21 (3), pp. 769-97.
31. [31] F.G. Caballero, H. Roelofs, S. Hasler, C. Capdevila, J. Chao, J. Cornide, and C. Garcia-Mateo: Mats. Sci. Tech., 2012, vol. 28, pp. 95-102.10.1179/1743284710Y.0000000047 ↗
32. [32] T. Furuhara, H. Kawata, S. Morito, and T. Maki: Mat. Sci. Eng. A., 2006, vol. 431, pp. 228-36.10.1016/j.msea.2006.06.032 ↗
33. [33] G. Krauss: Principles of heat treatment of steel, 1st ed., American Society for Metals, Metals Park, Ohio, 1980.
34. [34] H. Jarvinen, M. Isakov, T. Nyyssonen, M. Jarvenpaa, and P. Peura: Mat. Sci. Eng. A., 2016, vol. 676, pp. 109-20.10.1016/j.msea.2016.08.096 ↗
35. B. Abrivard, E. Pessard, F.M.P. Delhaye, and B. Gerin: 13th International Spring Meeting SF2M, May 22-23, Paris, France, 2013.
36. [36] D.K. Matlock, and J.G. Speer: Mater. Sci. Technol., 2009, vol. 25, 1118-25.10.1179/174328408X322222 ↗
37. [37] S. Vervynckt, K. Verbeken, B. Lopez, and J.J. Jonas: Int. Mater. Rev., 2012, vol. 57, pp. 187-207.10.1179/1743280411Y.0000000013 ↗
38. [38] H. Scott, J.D. Boyd and A.K. Pilkey: Mat. Sci. Eng. A., 2017, vol. 682, pp. 139-46.10.1016/j.msea.2016.11.020 ↗
39. [39] N. Pathak, C. Butcher, M.J. Worswick, E. Bellhouse and J. Gao: Materials, 2017, vol. 10, 1-29.10.3390/ma10040346 ↗
40. [40] Q. Lai, O. Bouaziz, M. Goune, L. Brassart, M. Verdier, G. Parry, A. Perlade, Y. Brecht, and T. Pardoen: Mat. Sci. Eng. A., 2015, vol. 646, pp. 322-31.10.1016/j.msea.2015.08.073 ↗
41. [41]G. Avramovic-Cingara, A.R. Saleh, M.K. Jain, and D.S. Wilkinson: Metall. Mater. Trans. A., 2009, vol. 40A, pp. 3117-27.10.1007/s11661-009-0030-z ↗
42. [42] J. Kadhodapour, A. Butz, and S. Ziaei Rad: Acta Mater., 2011, vol. 59, pp. 2575-88.10.1016/j.actamat.2010.12.039 ↗
43. [43] A.F. Szewczyk and J. Gurland: Metall. Trans. A., 1982, vol. 13A, pp. 1821-26.10.1007/BF02647838 ↗
44. [44] E. Maire, O. Bouaziz, M. Di Michiel, and C. Verdu: Acta Mater., 2008, vol. 56, pp. 4954-64.10.1016/j.actamat.2008.06.015 ↗
45. [45] J. Samei, D.G. Green, J. Cheng, and M.S. Lima: Mater. and Des., 2016, vol. 92, pp. 1028-37.10.1016/j.matdes.2015.12.103 ↗
46. [46] C.I.A. Thomson, M.J. Worswick, A.K. Pilkey, and D.J. Lloyd: J. Mech. Phys. Solids, 2003, vol. 51, pp. 127-46.10.1016/S0022-5096(02)00055-8 ↗
47. [47] M. Erdogan: J. Mater. Sci., 2002, vol. 37, pp. 3623-30.10.1023/A:1016548922555 ↗
48. [48] M. Azuma, S. Goutianos, N. Hansen, G. Winther, and X. Huang: Mater. Sci. Tech., 2012, vol. 28 (9-10), pp. 1092-100.10.1179/1743284712Y.0000000006 ↗
49. [49] N.J. Kim and G. Thomas, Metall. Mater. Trans. A., 1981, vol. 12A, pp. 483-89.10.1007/BF02648546 ↗
50. A.A. Benzerga: PhD Thesis, Ecole National Superieure des Mines de Paris, 2000.
51. [51] S. Zhang, Y. Huang, B. Sun, Q. Liao, H. Lu, B. Jian, H. Mohrbacher, W. Zhang, A. Guo, and Y. Zhang: Mat. Sci. Eng. A., 2015, vol. 626, pp. 136-43.10.1016/j.msea.2014.12.051 ↗
52. [52] C. Landron, E. Maire, O. Bouaziz, J. Adrien, L. Lecarme, and A. Bareggi: Acta Mater., 2011, vol. 59, pp. 7564-73.10.1016/j.actamat.2011.08.046 ↗