The Effectiveness of Al-Si Coatings for Preventing Interfacial Reaction in Al-Mg Dissimilar Metal Welding
Source abstract
Abstract
Abstract The dissimilar welding of aluminum to magnesium is challenging because of the rapid formation of brittle intermetallic compounds (IMC) at the weld interface. An Al-Si coating interlayer was selected to address this problem, based on thermodynamic calculations which predicted that silicon would change the reaction path to avoid formation of the normally observed binary Al-Mg IMC phases (β-Al3Mg2 and γ-Al12Mg17). Long-term static heat treatments confirmed that a Si-rich coating will preferentially produce the Mg2Si phase in competition with the less stable, β-Al3Mg2 and γ-Al12Mg17 binary IMC phases, and this reduced the overall reaction layer thickness. However, when an Al-Si clad sheet was tested in a real welding scenario, using the Refill™ friction stir spot welding (FSSW) technique, Mg2Si was only produced in very small amounts owing to the much shorter reaction time. Surprisingly, the coating still led to a significant reduction in the IMC reaction layer thickness and the welds exhibited enhanced mechanical performance, with improved strength and fracture energy. This beneficial behavior has been attributed to the softer coating material both reducing the welding temperature and giving rise to the incorporation of Si particles into the reaction layer, which toughened the brittle interfacial IMC phases during crack propagation.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. A. Jambor and M. Beyer: Mater. Des., 1997, vol. 18, pp. 203-09.10.1016/S0261-3069(97)00049-6 ↗
2. J. Hirsh: Metall. Mater. Trans. A, 2011, vol. 52, pp. 818-24.
3. A. Simar and M-N. Avettand-Fènoël: Sci. Technol. Weld Joining, 2017, vol. 22, pp. 389-40310.1080/13621718.2016.1251712 ↗
4. A. Panteli, J.D. Robson, I. Brough and P.B. Prangnell: Mater. Sci. Eng. A, 2012, vol. 556, pp. 31-42.10.1016/j.msea.2012.06.055 ↗
5. A.A. Mclean, G.L.F. Powell, I.H. Brown and V.M. Linton: Sci. Technol. Weld Joining., 2003, vol. 8, pp. 462-64.10.1179/136217103225009134 ↗
6. U.Suhuddin, V.Fischer, F.Kroeff, J.F.dosSantos: Mater. Sci. Eng., 2014, vol. 590, pp. 384–389.10.1016/j.msea.2013.10.057 ↗
7. Z. Liang, G. Qin, H. Ma, F. Yang and Z. Ao: Sci. Technol. Weld Joining, 2017, vol. 22, pp. 363-372.10.1080/13621718.2016.1248648 ↗
8. H.M. Rao, J.B. Jordon B. Ghaffari, X. Sub, A.K. Khosrovaneh, M.E. Barkey, W. Yuan, M. Guo: Int. J. of Fatigue, 82: 737–747.10.1016/j.ijfatigue.2015.09.033 ↗
9. Y. Wang, and P.B. Prangnell: Mater. Charact., 2017, in press.
10. D. Dietrich, D. Nickel, M. Krause, T. Lampke, M.P. Coleman and V. Randle: J. Mater. Sci., 2011, vol. 46, pp. 357-64.10.1007/s10853-010-4841-5 ↗
11. E.M. Tanguep Njiokep, M. Salamon, and H. Mehrer: Defect Diffus. Forum, 2001, vols. 194–199, pp. 1581–86.10.4028/www.scientific.net/DDF.194-199.1581 ↗
12. L. Wang, Y. Wang, P.B. Prangnell, J.D. Robson: Mater. Trans. A, 2015, vol. 46A, pp. 4106-14.10.1007/s11661-015-3037-7 ↗
13. S. Sampson: Acta Cryst., 1965, vol. 19, pp. 401-412.10.1107/S0365110X65005133 ↗
14. D.S. D’Antuono, M.L. Taheri, J. Gaies and W. Golumbfskie: Microsc. Microanal., 2012, vol. 18, pp. 1792-93.10.1017/S1431927612010811 ↗
15. A. Panteli, J.D. Robson, Y.-C. Chen and P.B. Prangnell: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 5773-81.10.1007/s11661-013-1928-z ↗
16. H. Zhang, J. Song, Materials Letters, 2011, vol. 65, pp. 3292-3294.10.1016/j.matlet.2011.05.080 ↗
17. L. Liu, L. Zhao, R. Xu, Materials and Design, 2009, vol. 30, pp. 4548-4551.10.1016/j.matdes.2009.04.040 ↗
18. Hui Zhang, Lingfeng Li, Yiqing Chen, Alan A. Luo and Lihua Liu: Int. J. of Cast Metals Research, 2016, vol. 29, pp. 338-343.10.1080/13640461.2016.1164915 ↗
19. M. Sun, S.T. Nikneja, H. Gao, L.Wu, Y. Zhou; Materials and Design, 2016, vol. 91, pp. 331–339.10.1016/j.matdes.2015.11.121 ↗
20. Y. Tang, Y. Du, L. Zhang, X. Yuan, G. Kaptay: Thermochimica Acta, 2012, vol. 527, pp.131– 142.10.1016/j.tca.2011.10.017 ↗
21. C. Schilling, and J.D. Santos: US6722556 B2, 2004.
22. R.B. Wagstaff, D.J. Lloyd and T.F. Bischoff: Mater. Sci. Forum, 2006, vol. 519-521, pp. 1809-14.10.4028/www.scientific.net/MSF.519-521.1809 ↗
23. B.M. Al-Zubaidy, Y-C. Chen, and P.B. Prangnell: Assessment of rapid refill FSSW for 6111-T4 aluminium automotive alloys, 14th Int. Frict. Stir Weld. Symp., Beijing, China, TWI. 2014.
24. B.M. Al-Zubaidy: Material interactions in a novel refill friction stir spot welding approach to joining Al-Al and Al-Mg automotive sheets. Ph.D. Thesis, The University of Manchester, Manchester, UK, 2017, pp. 216–39.
25. J.L. Murray and A.J. McAlister: Bull. Alloy Phase Diag., 1984, vol. 5, pp. 74-84.10.1007/BF02868729 ↗
26. K. Nakamura and M. Kamoshida: J. Appl. Phys., 1997, vol. 48, pp. 5349-51.10.1063/1.323572 ↗
27. D. Bradai, M. Kadi-Hanifi, P. Zieba, W. Kuschke and W. Gust: J. Mater. Sci., 1999, vol. 34, pp. 5331-36.10.1023/A:1004753122411 ↗
28. J. Zhang, Z. Fan, Y. Wang and B. Zhou: J. Mater. Sci. Lett., 1999, vol. 18, pp. 783-84.10.1023/A:1006684916145 ↗
29. M. Feuerbach, C. Thomas, J. Makongo, S. Hoffmann: Crystalline Materials, 2007 vol. 222, pp. 259-288.
30. A. Zolriasatein, R.A. Khosroshahi, M. Emamy, N. Nemati: Int. J. Min., Met., Mater., 2013, vol. 20, pp. 290-97.10.1007/s12613-013-0726-3 ↗
31. Y. Wang, G.-Q. Luo, L.-J. Li, Q. Shen and L.-M. Zhang: J. Mater. Sci., 2014, vol. 49, pp. 7298-08.10.1007/s10853-014-8440-8 ↗
32. S.Y. Betsofen, Y.R. Kolobov, E.F. Volkova, S.A. Bozhko and I.I. Voskresenskaya: Russ. Metall., 2015, vol. 2015, pp. 257-63.10.1134/S0036029515040035 ↗
33. H. Zhang, S.L. Shang, Y. Wang, A. Saengdeejing, L.Q. Chen and Z.K. Liu: Acta Mater., 2010, vol. 58, pp. 4012-18.10.1016/j.actamat.2010.03.020 ↗
34. A. Zolriasatein and A. Shokuhfar: Mater. Des., 2015, vol. 75, pp. 17-23.10.1016/j.matdes.2015.03.014 ↗
35. P. Venkateswaran, Z.-H. Xu, X.-D. Li and A.P. Reynolds: J. Mate Sci., 2009, vol. 44, pp. 4140-47.10.1007/s10853-009-3607-4 ↗
36. G.-H. Li, H.S. Gill and R.A. Varin: Metall. Metall. Trans. A, 1993, vol. 24, pp. 2383-239110.1007/BF02646518 ↗
37. L. Lu, M.Q. Lai and M.L. Hoe: Nanostruct. Mater., 1998, vol. 10, pp. 551-63.10.1016/S0965-9773(98)00102-0 ↗
38. Y.-Z. Lu, Q.-D. Wang, X.-Q. Zeng, W.-J. Ding and Y.-P. Zhu: J. Mater. Sci. Lett., 2001, vol. 20, pp. 397-99.10.1023/A:1010921608719 ↗
39. V. Milekhine, M.I. Onsøien, J.K. Solberg and T. Skaland: Intermetallics, 2002, vol. 10, pp. 743-50.10.1016/S0966-9795(02)00046-8 ↗
40. J. Tani and H. Kido: Comput. Mater. Sci., 2008, vol. 42, pp. 531-36.10.1016/j.commatsci.2007.08.018 ↗
41. G. Frommeyer, S. Beer and K.V. Oldenburg: Z. Metallkd., 1994, vol. 85, pp. 372-77.
42. D. Kevorkov, R. Schmid-Fetzer and F. Zhang: J. Phase Equilib. Diff., 2004, vol. 25, pp. 140-51.10.1007/s11669-004-0007-y ↗
43. U.F.H. Suhuddin, V. Fischer and J.F. dos Santos: Scripta Materialia, 2013, vol. 68, pp. 87–90.10.1016/j.scriptamat.2012.09.008 ↗
44. A. Reilly, H.R. Shercliff, Y.-C. Chen, P.B. Prangnell, J. Mater. Proc. Technol. 225: 473–84 (2015).10.1016/j.jmatprotec.2015.06.021 ↗
45. U.F.H. Suhuddin, V. Fischer, F. Kroeff and H.F. d. Santos: Mater. Sci. Eng., A, 2014, vol. 590, pp. 384-89.10.1016/j.msea.2013.10.057 ↗
46. M. Murayama and K. Hono: Acta Mater., 1999, vol. 47, pp. 1537-48.10.1016/S1359-6454(99)00033-6 ↗
47. C. Ravi and C. Wolverton: Acta Mater., 2004, vol. 52, pp. 4213-27.10.1016/j.actamat.2004.05.037 ↗
48. P. Jedrasiak, H.R. Shercliff, A. Reilly, G. J. McShane, Y.C. Chen, L. Wang, J.D. Robson, and P.B. Prangnell: J. Materials Eng. and Performance, 2017, vol. 25, pp. 4089-409810.1007/s11665-016-2225-y ↗