Wear Behavior of a Novel Aluminum-Based Hybrid Composite
Source abstract
Abstract
In the current research, the dry sliding wear behaviors of 6351 Al alloy and its composite with hybrid reinforcement (ex situ SiC and in situ Al4SiC4) were investigated at low sliding speed (1 m s−1) against a hardened EN 31 disk at different loads. The wear mechanism involved adhesion and microcutting-abrasion at lower load. On the other hand, at higher load, abrasive wear involving microcutting and microplowing along with adherent oxide formation was observed. Initially, under higher load, the abrasive wear mechanism caused rapid wear loss up to a certain sliding distance. Afterward, by virtue of frictional heat generation and associated temperature rise, an adherent oxide layer was developed at the pin surface which drastically reduced the wear loss. The overall wear rate increased with load in alloy as well as in composite. Moreover, the overall wear rate of the composite was found lower than that of the 6351 Al alloy at all applied loads. The ex situ SiC particles were found to resist abrasive wear, while, in situ Al4SiC4 particles offered resistance to adhesive wear. Accordingly, the 6351 Al (SiC + Al4SiC4) hybrid composite exhibited superior wear resistance relative to the 6351 Al alloy.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · MXene and MAX Phase Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. H. C. Park: Scr. Met. et Mat., 1992, vol. 27, pp. 465-470.10.1016/0956-716X(92)90212-W ↗
2. D. Huda, M.A. El baradie, and M.S.J. Hashmi: J. Mater. Process. Technol., 1993, vol. 37, pp. 529–41.10.1016/0924-0136(93)90115-M ↗
3. T.J. Lienert, W.A. Baeslack, J. Ringnalda, and H.L. Fraser: J. Mater. Sci., 1996, vol. 31, pp. 2149 -2157.10.1007/BF00356639 ↗
4. R. L. Deuis, C. Subramanian and J. M. Yellup: Compos. Sci. Technol., 1997, vol. 57, pp. 415-435.10.1016/S0266-3538(96)00167-4 ↗
5. K.S. Al-Rubaie, H.N. Yoshimura and J.D.B. Mello: Wear, 1999, vols. 233–235, pp. 444–454.10.1016/S0043-1648(99)00185-4 ↗
6. K.S. Al-Rubaie, H. Goldenstein and J.D.B. Mello: Wear, 1999, vols. 225–229, pp. 163–173.10.1016/S0043-1648(99)00009-5 ↗
7. A.G. Wang and I.M. Hutchings: Mater. Sci. Technol., 1989, vol. 5, pp. 71–76.10.1179/026708389790337503 ↗
8. R. Ipek: J. Mater. Process. Technol., 2005, vols. 162–163, pp. 71–75.10.1016/j.jmatprotec.2005.02.207 ↗
9. P.A. Patricia, P. Sisa and O. Enoch: Adv. Mater. Res., 2011, vol. 227, pp. 23-26.10.4028/www.scientific.net/AMR.227.23 ↗
10. R. Tyagi: Wear, 2005, vol. 259, pp. 569–576.10.1016/j.wear.2005.01.051 ↗
11. T.T. Long, T. Aisaka, M. Ose, and M. Morita: J. Japan Inst. Metals, 1987, vol. 51, pp. 864.10.2320/jinstmet1952.51.9_864 ↗
12. T. Lim, C.S. Lee, Y.H. Kim, and K.S. Han: Proc. ICCM/VIII, Honolulu, 20-E, 1991, pp. 1–14.
13. K.H. Oh and K.S. Han: Compos. Sci. Technol., 2007, vol. 67, pp. 1719–1726.10.1016/j.compscitech.2006.06.020 ↗
14. J.I. Song and K.S. Han: Compos. Struct., 1997, vol. 39, pp. 309-318.10.1016/S0263-8223(97)00124-4 ↗
15. J.I. Song, H.D. Bong, and K.M. Han: Scripta Metall. Mater., 1995, vol. 33, pp. 1307–13.10.1016/0956-716X(95)00359-4 ↗
16. M. Abdel Aziz, T.S. Mahmoud and A. Abdel Aal: Mater. Sci. Eng. A, 2008, vol. 486, pp. 313–320.10.1016/j.msea.2007.11.066 ↗
17. M. Gupta, M.O. Lai and C.Y.H. Lim: J. Mater. Process. Technol., 2006, vol. 176, pp. 191-199.10.1016/j.jmatprotec.2006.03.130 ↗
18. A.B. Gurcan and T.N. Baker: Wear, 1995, vol. 188, pp.185-191.10.1016/0043-1648(95)06639-X ↗
19. M.K. Mondal, K. Biswas, and J. Maity: J. Mater. Eng. Perform., 2013, doi: 10.1007/s11665-013-0654-4.10.1007/s11665-013-0654-4 ↗
20. Anon: Ceramics and Glasses, Engineering Materials Handbook, vol. 4, ASM International, The Materials Information Society, Materials Park, OH, 1991, p. 30.
21. G.W. Wen and X.X. Huang: J. Eur. Ceram. Soc., 2006, vol. 26, pp. 1281–1286.10.1016/j.jeurceramsoc.2004.12.032 ↗
22. S. Kumar, A. Bhattacharyya, D.K. Mondal, K. Biswas and J. Maity: Wear, 2011, vol. 270, pp. 413–421.10.1016/j.wear.2010.12.007 ↗
23. K.L. Sahoo, C.S.S. Krishnan and A.K. Chakrabarti: Wear, 2000, vol. 239, pp. 211–218.10.1016/S0043-1648(99)00371-3 ↗
24. N.P. Suh: Wear, 1973, vol. 25, pp. 111-124.10.1016/0043-1648(73)90125-7 ↗
25. K.-H.Z. Gahr: Abrasive Wear on Metallic Materials, Metallurgical Aspects of Wear, German Society of Metallurgy, Germany, 1981, pp. 73–103.
26. Y. Berthier, M. Godet and M. Brendle: Tribol. Trans., 1989, vol. 32, pp. 490-496.10.1080/10402008908981917 ↗
27. S.Q. Wang, M.X. Wei and Y.T. Zhao: Wear, 2010, vol. 269, pp. 424–434.10.1016/j.wear.2010.04.028 ↗
28. F.P. Bowden and D. Tabor: The Friction and Lubrication of Solids, Clarendon Press, Oxford, 1986, pp 112–120.
29. G. Straffelini, D. Trabucco and A. Molinari: Wear, 2001, vol. 250, pp. 485–491.10.1016/S0043-1648(01)00661-5 ↗
30. G.W. Stachoiak and A.W. Batchelor: Engineering Tribology, Tribology Series 24, Elsevier, Amsterdam, 1993.
31. F.H. Stott: Tribol. Int., 1998, vol. 31, pp. 61–71.10.1016/S0301-679X(98)00008-5 ↗
32. Anon: Properties and Selection: Non-ferrous Alloys and Special-Purpose Materials, Metals Handbook, vol. 2, 10th ed., ASM International, The Materials Information Society, Materials Park, OH, 1990, p. 426.
33. R. Choudhary, H. Kumar and R.K. Garg: Indian J. Eng. Mater. Sci., 2010, vol. 17, pp. 91-98.
34. Anon: Thermal Properties of Metals, ASM Ready Reference, ASM International, The Materials Information Society, Materials Park, OH, 2002, p. 224.
35. J. Jiang, F. H.Stott and M. M.Stack, Wear, 1995, vols. 181-183, pp.20-31.10.1016/0043-1648(95)90004-7 ↗
36. J. Zhang and A. T. Alpas: Acta mater., 1997, Vol. 45, pp. 513-528.10.1016/S1359-6454(96)00191-7 ↗
37. S. C. Lim and M. F. Ashby: Acta Metall., 1987, vol. 35, pp. 1–24.10.1016/0001-6160(87)90209-4 ↗
38. W. Hirst and J. K. Lancaster: Proc. Roy. Sot. A, 1960, vol. 259, pp. 228-241.10.1098/rspa.1960.0220 ↗
39. N. Saka, A. M. Eleiche and N. P. Sub: Wear, 1977, vol. 44, pp. 109-125.10.1016/0043-1648(77)90089-8 ↗
40. I. Koji, M. Satoshi and Y. Akira: J. Ceram. Soc. Jpn., 2003, vol. 111, pp. 348-351.10.2109/jcersj.111.348 ↗
41. K. Itatani, T. Tanaka, and I. J. Davies, J. Europ. Ceram. Soc., 2006, vol. 26, pp. 703-710.10.1016/j.jeurceramsoc.2005.07.008 ↗