journal article·2020-04Open access

Revisiting “Steady-State” Monotonic and Cyclic Deformation: Emphasizing the Quasi-Stationary State of Deformation

Haël Mughrabi

Abstract

Abstract High-temperature creep, cyclic deformation in saturation, and a number of technologically important processes are typical examples of the so-called “steady-state” deformation. These cases are usually defined in terms of the constancy of the mechanical parameters. Moreover, it is usually assumed that the deformation-induced microstructure undergoes no further changes. However, clear evidence shows that non-negligible microstructural changes continue to occur in the so-defined steady-state high-temperature creep and in cyclic saturation. It can be shown that the so-called “steady-state” deformation is actually a quasi-stationary deformation which is characterized by the initial development of a “mechanical steady state”, which is followed with a delay by a “microstructural steady state.” Only the latter can then be considered as a true steady state. A deeper analysis reveals a persistent slight increase of the dislocation density, with geometrically necessary dislocations in the cell walls/subgrain boundaries, causing the latter to transform gradually into sharper boundaries with higher misorientations. These findings, based on a detailed analysis of a wide range of experimental studies, are found to be almost identical for both high-temperature creep and cyclic deformation in saturation and are hence considered as characteristic of quasi-stationary deformation. The analysis clarifies, as a by-product, specific effects which arise from the increasing heterogeneity of the dislocation pattern (patterning). Thus, a marked decrease of the arrangement factor “alpha” in the Taylor flow stress is noted, as patterning proceeds, in agreement with predictions of the so-called composite model. Since this effect is compensated partially by the increase of the dislocation density, the flow stress remains rather insensitive to subtle microstructural changes. Based on these facts, the need for revision of current flow-stress formulations in future dislocation modeling is emphasized.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and mechanical properties · Hydrogen embrittlement and corrosion behaviors in metals · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (62)

Show source-provided references
1. W.A. Backofen, 1972, Deformation processing, Addison-Wesley Pub. Co., p. 227.
2. P. Montmitonnet: Materials Processing and Design, Modeling, Simulation and Applications, NUMIFORM ’07: 9th International Conferenceon Numerical Methods in Industrial Forming Processes, 2007, pp. 209–14.
3. R. Pippan, S. Scheriau, A. Taylor, M. Hafok, A. Hohenwarter, A. Bachmaier: 2010, Annual Review of Materials Research, 40, 319-343.10.1146/annurev-matsci-070909-104445 ↗
4. O. Renk, A. Hohenwarter, S. Wurster, R. Pippan: 2014, Acta materialia, 77, 401-410.10.1016/j.actamat.2014.06.010 ↗
5. M. D. Zoback, J. Townsend, B. Grollimund: 2002, Int. Geology Review, 44, 383-401.10.2747/0020-6814.44.5.383 ↗
6. K. Wang, V. Hu, J. He: 2012, Nature, 484, 327-332.10.1038/nature11032 ↗
7. S. Hawking : 1988, A brief history of time : from the Big Bang to Black Holes, Bantam Books, New York, 1988.10.1063/1.2811637 ↗
8. H. Mughrabi: Z. Metallkde, 2005, vol. 96, 546-551.10.3139/146.101068 ↗
9. H. Mughrabi: Current Opinion in Solid State and Materials Science, 2016, vol. 20, 411-420.10.1016/j.cossms.2016.07.001 ↗
10. W. Blum: Private communication, and Materials Science and Technology, Plastic Deformation and Fracture, R.W. Cahn, P. Haasen, E.J. Kramer, eds., H. Mughrabi, VCH, Weinheim, 1993, vol. 6, pp. 361–405.
11. C. Laird: in Dislocations in Solids, vol. 6, F.R.N. Nabarro, ed. North-Holland Publishing Company, 1983, pp. 57–120.
12. H. Mughrabi: Dislocations and Properties of Real Materials (Conf. Proc.), Book No. 323, The Institute of Metals, London, 1984, pp. 244–60.
13. S. Suresh: Fatigue of Materials, 2nd. Ed., Cambridge University Press, Cambridge, 1998.10.1017/CBO9780511806575 ↗
14. W. Blum, J. Dvořák, P. Král, P. Eisenlohr, V. Sklenička: 2014, Journal of Materials Science, 49, 2987-2997.10.1007/s10853-013-7983-4 ↗
15. W. Blum, J. Dvořák, P. Král, P. Eisenlohr, V. Sklenička: 2015, J. Mater. Sci. & Technolog., 31, 1065-1068.10.1016/j.jmst.2015.09.012 ↗
16. Y. Huang: IOP Conf. Ser. 2017, 219, 1-8.
17. L.P. Kubin: Materials Science and Technology in Plastic Deformation and Fracture, R.W. Cahn, P. Haasen, E.J. Kramer, eds., H. Mughrabi, VCH, Weinheim, 1993, vol. 6, pp. 137–90.
18. G.I. Taylor: Proc. Roy. Soc. London 1934, vol. 145, 362-387.
19. G. Saada: Acta Metallurgica, 1960, vol. 8, 841-847.10.1016/0001-6160(60)90150-4 ↗
20. G. Schoeck, R. Frydman, Phys. Stat. sol. B 1972, 53, 661-673.10.1002/pssb.2220530227 ↗
21. B. Devincre, T. Hoc, L. Kubin, Science 2008, vol. 320, 1745-1748.10.1126/science.1156101 ↗
22. L.P. Kubin, B. Devincre, T. Hoc: Mater. Sci. Eng. A, 2008, vol. 483-484, 19-24.10.1016/j.msea.2007.01.167 ↗
23. M. Sauzay, L.P. Kubin: Progr. Mater. Sci. 2012, vol. 56, 725-784.10.1016/j.pmatsci.2011.01.006 ↗
24. H. Mughrabi, R. Kütterer, K. Lubitz, H. Kronmüller: 1976, Phys. Status Solidi. A, 38, 261-7010.1002/pssa.2210380129 ↗
25. H. Mughrabi, T. Ungár: Dislocations in Solids, vol. 11, F.R.N. Nabarro and S. Duesberry, eds., Elsevier Science Elsevier Science, 2002, pp. 343–411.10.1016/S1572-4859(02)80011-0 ↗
26. H. Mughrabi: 1971, Phil. Mag., vol. 23, 897- 929.10.1080/14786437108216995 ↗
27. H. Mughrabi, T. Ungár, W. Kienle, M. Wilkens: Phil. Mag. 1986, vol. 53, 793-813.10.1080/01418618608245293 ↗
28. H. Mughrabi, K. Herz, X. Stark: 1981, Int. J. Fract., 17, 193-32010.1007/BF00053520 ↗
29. H. Mughrabi, R. Wang: Deformation of Polycrystals: Mechanisms and Microstructures, Proceedings of 2nd Risoe International Symposium, N. Hansen ed., 1981, pp. 87–98.
30. M.E. Kassner, A.A. Ziaai-Moayyed, A.K. Miller: 1985, Met. Trans. A, 16A,1069-1076.10.1007/BF02811676 ↗
31. F. Petry, F. Pschenitzka: Mater. Sci Eng. 1984, vol. 68, L7 – L11.10.1016/0025-5416(84)90258-1 ↗
32. H. Mughrabi: Acta metallurgica, 1983, vol. 31, 1367-1379.10.1016/0001-6160(83)90007-X ↗
33. H. Mughrabi: Mater. Sci. Eng. 1987, vol. 85, 5-31.10.1016/0025-5416(87)90463-0 ↗
34. Z.S. Basinski: 1974, Scripta metallurgica 1974, vol. 8, 1301-1308.10.1016/0036-9748(74)90350-0 ↗
35. A.H. Cottrell: Dislocations and Plastic Flow in Crystals, Oxford University Press, Oxford, 1953, p. 208.
36. A. Seeger: Phil. Mag. 1954, vol. 45, 771-73.10.1080/14786440708520489 ↗
37. M.E. Kassner, M.-T.Pérez-Prado: Progr. Mater. Sci. 2000, vol. 45, 1-102.10.1016/S0079-6425(99)00006-7 ↗
38. M.E. Kassner, J.W. Elmer, C.J. Echer: Metall. Trans. A, 1986, vol. 17, 2093-2097.10.1007/BF02645011 ↗
39. M.E. Kassner, M.E. McMahon: Metall. Trans. A, 1987, vol. 18, 835-846.10.1007/BF02646925 ↗
40. M.F. Ashby: Phil. Mag. 1970, vol. 21, 399-424.10.1080/14786437008238426 ↗
41. H. Mughrabi: Mater. Sci. Eng. A 2001, vol. 317, 171-180.10.1016/S0921-5093(01)01173-X ↗
42. J. Weertman: Proceedings of 20th Risoe International Symposium on Materials Science, N. Hansen, D. Juul-Jensen, T. Leffers, W. Pantleon, O.B. Pedersen, G. Winther, eds., Roskilde, Denmark, 1999, pp. 201–12.
43. R. Wang, H. Mughrabi, S. McGovern, M. Rapp: Mater. Sci. Eng. 1984, 65, 219-23310.1016/0025-5416(84)90084-3 ↗
44. R. Wang, H. Mughrabi: Mater. Sci. Eng. 1984, vol. 63, 147-163.10.1016/0025-5416(84)90118-6 ↗
45. H. Mughrabi, F. Ackermann and K. Herz: Fatigue Mechanisms, Proc. of an ASTM-NBS-NF Symposium, J.T. Fong, ed., ASTM-STP 675, American Society for Testing and Materials, Philadelphia, 1979, pp. 69–105.
46. M. Wilkens, K. Herz, H. Mughrabi: 1980, Z. Metallkde, 96, 546-51.
47. J. Polák: Czech J. Phys. 1969, vol. B 19, 315-322.10.1007/BF01712868 ↗
48. W. Wolf: Untersuchungen der Versetzungsanordnung wechsel- und zugverformter Nickel-Einkristalle mit Hilfe magnetischer Methoden. Technische Hochschule Stuttgart, Doctorate Thesis: 1980.
49. J. Pratt, Acta metall. 1967, vol. 15, 319-327.10.1016/0001-6160(67)90208-8 ↗
50. S.V. Raj, G.M. Pharr: Mater. Sci. Eng. 1986, 81, 217-37.10.1016/0025-5416(86)90265-X ↗
51. C.E. Feltner, C. Laird: 1967, Acta metall., vol 15, 1621- 1632.10.1016/0001-6160(67)90137-X ↗
52. R.C. Daniel, G.T. Horne: Metall. Trans., 2:1161–1172, 197110.1007/BF02664248 ↗
53. M.R. Staker, D.L. Holt, 1972, Acta Metall., 20, 569-79.10.1016/0001-6160(72)90012-0 ↗
54. D.J. Abson, J.J. Jonas, 1970, Metal Sci. J., vol. 4, 24-28.10.1179/msc.1970.4.1.24 ↗
55. F.N. Mandigo: Ph. D. Thesis, Cornell University, 1972.
56. D. Kuhlmann-Wilsdorf: Met. Soc. AIME., 224, 1047-1061, 1962.
57. S. Groh, H. M. Zbib: 2009, J. Eng. Mater. Technol, 131, 041209.10.1115/1.3183783 ↗
58. M. Fivel, C. Déprés: 2014, Phil. Mag.,vol. 94, 3206-3214.10.1080/14786435.2014.949326 ↗
59. G. Po, M.S. Mohamed, T. Crosby, C. Erel, A. El-Azab, N. Ghoniem: 2014, JOM, 66, 2108-20.10.1007/s11837-014-1153-2 ↗
60. S.X. Xia, A. El-Azab: 2015, IOP Conf. Series 89, 012053, 1-9.
61. C. Erel, G. Po, N. Ghoniem: 2017, Phil. Mag. vol. 97, 2897-2970.10.1080/14786435.2017.1361555 ↗
62. S. Papanikolaou, Y. Cui, N. Ghoniem: Modelling and Simulation in Materials Science and Engineering, vol. 26, No. 1, Focus on MMM 2016.10.1088/1361-651X/aa97ad ↗