Microstructural Degradation and the Effects on Creep Properties of a Hot Corrosion-Resistant Single-Crystal Ni-Based Superalloy During Long-Term Thermal Exposure
Source abstract
Abstract
In the present study, the kinetics of microstructural degradation during long-term thermal exposure (LTTE) and the effects on creep deformation mechanisms of a hot corrosion-resistant single-crystal Ni-based superalloy with a low γ′ volume fraction and γ/γ′ lattice misfit were investigated in detail. The kinetic of γ′ coarsening in the experimental alloy conforms well to the Lifshitz–Slyozov–Wagner theory during LTTE at 900 °C up to 10,000 hours. The evolution of γ/γ′ lattice misfit during the LTTE was also investigated by a first attempt. The focused research emphasized on the influences of γ/γ′ lattice misfit evolution after the LTTE on the microstructural degradation, dislocation motion, and different creep mechanisms during high-temperature low-stress creep and high-temperature high-stress creep. The results show that the decreasing of the absolute values of γ/γ′ lattice misfit and change of γ′ size and morphology after the LTTE contribute to the weakening of barrier to the dislocation cutting process into γ′ precipitates during creep and the sharp reduction of stress-rupture lifetime at 950 °C/280 MPa after 1000 hours exposure. As the applied stress decreased to 230 MPa at 950 °C, the creep mechanisms change from the dislocation cutting through γ′ precipitates at high applied stress to the dislocation glide and climb around γ′ precipitates. The dislocation glide and climb by-pass deformation mechanism were not significantly influenced by the change of γ′ precipitates morphology and magnitude of γ/γ′ mismatch within 1000 hours thermal exposure, and the minimum creep rate and creep lifetime after 1000 hours thermal exposure were similar to that of the original heat-treated samples.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · High-Temperature Coating Behaviors · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. [1] T.M. Pollock, S. Tin: J. Propul. Power., 2006, vol. 22, pp. 361-74.10.2514/1.18239 ↗
2. [2] M. Konter, M. Thumann: J. Mater. Process. Technol., 2001, vol. 117, pp. 386-90.10.1016/S0924-0136(01)00785-3 ↗
3. R.C. Reed, J.J. Moverare, A. Sato, F. Karlsson, M. Hasselqvist: In Superalloys 2012, E. S. Huron, R.C. Reed, M.C. Hardy, M.J. Mills, R.E. Montero, P.D. Portella and J. Telesman, eds., TMS, Warrendale, PA, 2012, pp. 197-204.10.1002/9781118516430.ch22 ↗
4. I. Okada, T. Torigoe, K. Takahashi, D. Izutsu: In Superalloys 2004, K.A. Green, T.M. Pollock, H. Harada, T.E. Howson, R.C. Reed, J.J. Schirra and S. Walston, eds., TMS, Warrendale, PA, 2004, pp.707-12.10.7449/2004/Superalloys_2004_707_712 ↗
5. [5] R.C. Reed: The Superalloys, Fundamentals and Applications, Cambridge University Press, Cambridge, 2006.10.1017/CBO9780511541285 ↗
6. [6] M.V. Nathal: Metall. Trans. A, 1987, vol. 18A, pp. 1961-70.10.1007/BF02647026 ↗
7. T. Murakumo, Y. Koizumi, K. Kobayashi, H. Harada: In Superalloys 2004, K.A. Green, T.M. Pollock, H. Harada, T.E. Howson, R.C. Reed, J.J. Schirra and S. Walston, eds., TMS, Warrendale, PA, 2004, pp.189-95.
8. [8] T. Murakumo, T. Kobayashi, Y. Koizumi, H. Harada: Acta Mater., 2004, vol. 52, pp. 3737-44.10.1016/j.actamat.2004.04.028 ↗
9. A. Royer, P. Bastie: : In Superalloys 1996, R.D. Kissinger, D.J. Deye, D.L. Anton, A.D. Cetel, M.V. Nathal T.M. Pollock, and D.A. Woodford, eds., TMS, Warrendale, PA, 1996, pp. 221-28.
10. A. Epishin, T. Link, U. Brückner, B. Fedelich, and P. Portella: In Superalloys, K.A. Green, T.M. Pollock, H. Harada, T.E. Howson, R.C. Reed, J.J. Schirra and S. Walston, eds., TMS, Warrendale, PA, 2004, pp.537-43.
11. T. Murakumo, Y. Koizumi, K. kobayashi and H. Harada: In Superalloys 2004, K. A. Green, T. M. Pollock, H. Harada, T. E. Howson, R. C. reed, J. J. Scirra and S. Walston, eds., pp. 115-62.
12. X.W. Jiang, D. Wang, G. Xie, H. Li, L.H. Lou L, J. Zhang: Metall. Mater. Trans. A., 2014, vol. 45A, pp. 6016-26.
13. [13] M.V. Acharya, G.E. Fuchs: Mater. Sci. Eng. A, 2004, vol. 381, pp. 143-53.10.1016/j.msea.2004.04.001 ↗
14. [14] F. Pyczak, S. Neumeier, M. Göken: Mater. Sci. Eng. A, 2009, vol. 510-511, 295-300.10.1016/j.msea.2008.08.052 ↗
15. [15] S. Socrate, D.M. Parks: Acta Metall Mater., 1993, vol. 41, pp. 2185-2209.10.1016/0956-7151(93)90389-A ↗
16. [16] F. Diologent, P. Caron, T. D’Almeida, A. Jacques, P. Bastie: Nucl. Instrum. Methods Phys. Res., Sect. B, 2003, vol. 200, pp. 346-51.10.1016/S0168-583X(02)01699-3 ↗
17. [17] M. Fährmann, W. Hermann, E. Fährmann, A. Boegli, T.M. Pollock, and H.G. Sockel: Mater. Sci. Eng. A, 1999, vol. 260, pp. 212-21.10.1016/S0921-5093(98)00953-8 ↗
18. T.M. Pollock and R.D. Field: in Dislocation in Solids, F.R.N. Nabarro and M.S. Duesbery, eds., Elsevier Science B.V., Amsterdam, Netherlands, 2002, vol. 11, pp. 547-618.10.1016/S1572-4859(02)80014-6 ↗
19. [19] L.J. Carroll, Q. Feng, J.F. Mansfield, and T.M. Pollock: Metall. Mater. Trans. A., 2006, vol. 37A, pp. 2927-38.10.1007/s11661-006-0174-z ↗
20. [20] X.G. Wang, J.L. Liu, T. Jin, X.F. Sun, Z.Q. Hu, J.H. Do, B.G. Choi, I.S. Kim, C.Y. Jo: Mater Des., 2015, vol. 17, pp. 543-51.10.1016/j.matdes.2014.11.002 ↗
21. [21] J.X. Zhang, J.C. Wang, H. Harada, Y. Koizumi: Acta Mater., 2005, vol. 53, pp. 4623-33.10.1016/j.actamat.2005.06.013 ↗
22. [22] J.X. Zhang, T. Murakumo, Y. Koizumi, T. Kobayashi, T. Murakumo and H. Harada: Metall. Mater. Trans. A., 2004, vol. 35A, pp. 1911-14.10.1007/s11661-004-0100-1 ↗
23. [23] J.X. Zhang, T. Murakumo, Y. Koizumi, T. Kobayashi, T. Murakumo, H. Harada, S. Masaki JR: Metall. Mater. Trans. A, 2002, vol. 33, pp. 3741-46.10.1007/s11661-002-0246-7 ↗
24. [24] M. Aghaie-Khafri and S. Farahany: J. Mater. Eng. Perform., 2010, vol. 19, pp. 1065-70.10.1007/s11665-009-9584-6 ↗
25. X.W. Jiang, D. Wang, G. Xie, H. Li, L.H. Lou L, J. Zhang: Metall. Mater. Trans. A., 2014, vol. 45A, pp. 6016-26.10.1007/s11661-014-2559-8 ↗
26. [26] X.Z. Qin, J.T. Guo, C. Yuan, C.L. Chen, and H.Q. Ye: Metall. Mater. Trans. A., 2007, vol. 38A, pp. 3014-22.10.1007/s11661-007-9381-5 ↗
27. [27] J.L. Liu, T. Jin, J.J. Yu, X.F. Sun, H.R. Guan, Z.Q. Hu: Mater. Sci. Eng. A, 2010, vol. 527, pp. 890-97.10.1016/j.msea.2009.10.001 ↗
28. [28] A. Ges, O. Fornaro, F. Palacio: J Mater Sci., 1997, vol. 32, pp. 3687-91.10.1023/A:1018694716756 ↗
29. [29] M. Doi, T. Miyazaqui and T. Wakatsuki: Mater. Sci. Eng., 1984, vol. 67. pp. 247-53.10.1016/0025-5416(84)90056-9 ↗
30. [30] A. Baldan: J Mater Sci., 2002, vol. 37, pp. 2171-2202.10.1023/A:1015388912729 ↗
31. [31] A. Baldan: J Mater Sci., 2002, vol. 37, pp. 2379-2405.10.1023/A:1015408116016 ↗
32. [32] R.S. Moshtaghin, S. Asgari: Mater Des., 2003, vol. 24, pp. 325-30.10.1016/S0261-3069(03)00061-X ↗
33. [33] T.M. Pollock and A.S. Argon: Acta Metall. Mater., 1992, vol. 40, pp. 1-30.10.1016/0956-7151(92)90195-K ↗
34. [34] H. Rouault-Rogez, M. Dupeux, and M. Ignat: Acta Metall. Mater., 1994, vol. 42, pp. 3137.10.1016/0956-7151(94)90411-1 ↗
35. [35] J.T. Guo, D. Ranucci, E. Picco, P. M. Strocchi: Metall. Trans. A, 1983, vol. 14, pp. 2329-35.10.1007/BF02663308 ↗
36. [36] N. Matan, D.C. Cox, P. Cater, M.A. Rist, C.M.F. Rae, R.C. Reed: Acta Mater., 1999, vol. 47, pp.1549-63.10.1016/S1359-6454(99)00029-4 ↗
37. [37] C.M.F. Rae, R.C. Reed: Acta Mater., 2007, vol. 55, pp. 1067-81.10.1016/j.actamat.2006.09.026 ↗
38. [38] J.X. Zhang, T. Murakumo, Y. Koizumi, T. Kobayashi, H. Harada: Acta Mater., 2003, vol. 51, pp.5073-81.10.1016/S1359-6454(03)00355-0 ↗
39. [39] I. Lifshitz and V. Slyozov: J. Phys. Chem. Solids, 1961, vol. 19, pp. 35.10.1016/0022-3697(61)90054-3 ↗
40. [40] C. Wagner: Z. Elect., 1961, vol. 65, pp. 581.
41. [41] R.A. Mackay, M.V. Nathal: Acta Metall. Mater., 1996, vol.38, pp. 1993-2005.
42. [42] H.B. Long, H. Wei, Y.N. Liu, S.C. Mao, J.X. Zhang, S.S. Xiang, Y.H. Chen, W.M. Gui, Q. Li, Z. Zhang, X.D. Han: Acta Mater., 2016, vol. 120, pp. 95-107.10.1016/j.actamat.2016.08.035 ↗
43. [43] T. Grosdidier, A. Hazotte, A. Simon: Mater. Sci. Eng. A, 1998, vol. 256, pp. 183-96.10.1016/S0921-5093(98)00795-3 ↗
44. [44] R. Sharghi-Moshtaghin, S. Asgari: J. Mater. Process. Technol., 2004, vol. 147, pp. 343-50.10.1016/j.jmatprotec.2004.01.006 ↗
45. [45] R.A. Stevens, P.E.J. Flewitt: Mater. Sci. Eng., 1979, vol. 37, pp. 237-47.10.1016/0025-5416(79)90157-5 ↗
46. [46] J. Wang, L.Z. Zhou, L.Y. Sheng, J.T. Guo: Mater. Des., 2012, vol. 39, pp. 55-62.10.1016/j.matdes.2012.02.020 ↗
47. [48] H.E. Collins: Metall. Trans., 1974, vol. 5, pp. 189-204.10.1007/BF02642943 ↗
48. [49] E. Lvova: J. Mater. Eng. Perform., 2007, vol. 16, pp, 254-64.10.1007/s11665-007-9046-y ↗
49. [50] C. Yuan, J.T. Guo, H. C. Yang and S.H. Wang: Scripta Mater., 1998, vol. 39, pp. 991-97.10.1016/S1359-6462(98)00255-3 ↗
50. [51] L.Z. He, Q. Zheng, X.F. Sun, H.R. Guan, Z.Q. Hu, A.K. Tieu, C. Lu, and H.T. Zhu: Metall. Mater. Trans. A., 2005, vol. 36A, pp. 2385-91.10.1007/s11661-005-0111-6 ↗
51. [52] N. Matan, D.C. Cox, CMF Rae, RC Reed: Acta Mater., 1999, vol. 47, pp.2031-45.10.1016/S1359-6454(99)00093-2 ↗
52. G.L. Erickson: in Superalloys 1996, R.D. Kissinger et al., eds., TMS, Warrendale, PA, 1996, p. 45.10.7449/1996/Superalloys_1996_45_52 ↗
53. [54] D. Mukherji, H. Gabrisch, W. Chen, H.J. Fecht, and R.P. Wahi: Acta Mater., 1997, vol. 45, pp. 3143-54.10.1016/S1359-6454(97)00005-0 ↗
54. [55] D.W. MacLachlan, D.M. Knowles: Metall. Mater. Trans. A., 2000, vol. 31A, pp. 1401-11.10.1007/s11661-000-0258-0 ↗
55. [56] J.X. Zhang, H. Harada, Y. Koizumi, T. Kobayashi: J Mater Sci., 2010, vol. 45, pp. 523-32.10.1007/s10853-009-3970-1 ↗