A novel process for fabricating electrical contact SnO2/Ag composites by reciprocating extrusion
Source abstract
Abstract
Reciprocating extrusion combined with simple powder compaction was used to produce electrical contact SnO2/Ag composites from Ag and SnO2 powders with improved properties. The SnO2 particles were uniformly dispersed in the Ag matrix after 20 passes of extrusion. The hardness of the composites increased with extrusion passes and leveled off after ten passes, whereas the electrical conductivity decreased slowly after five passes. The variation of the coefficient of thermal expansion with temperature revealed that SnO2/Ag interface strength increased with extrusion passes and was greatest after 20 passes. The SnO2/Ag composites with 20 passes showed the best electrical contact properties in which there was no mass loss through mass transfer from cathode to anode during the make-break erosion test at both low and high current conditions. On the other hand, SnO2/Ag composites with one pass and commercial SnO2-In2O3/Ag specimens had an apparent mass loss under the same condition. Electrical contact composites produced by the present method are promising in electrical contact applications in consideration of cost and performance.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electrical Contact Performance and Analysis · Electronic Packaging and Soldering Technologies · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Y.S. Shen, Pat Lattari, Jeffrey Gardner, and Harold Wiegard: ASM Metals Handbook, 10th ed., ASM INTERNATIONAL, Metals Park, OH, 1990, vol. 2, pp. 840–68.
2. Howard E. Boyer and Timothy L. Gall: Metals Handbook, Desk ed., ASM, Metals Park, OH, 1985, pp. 20.16–20.21.
3. N.S. Hoyer: ASM Metals Handbook, 9th ed., ASM INTERNATIONAL, Metals Park, OH, 1984, vol. 7, pp. 630–34.
4. M. Huck, A. Kraus, R. Michal, and K.E. Saeger: Proc. 36th IEEE Holm Conf. on Electrical Contacts, 1990, pp. 133–38.
5. M. Sun, Q. Wang, and M. Lindmayer: IEEE Trans. Component Packaging A, 1994, vol. 17 (3), pp. 490–94.10.1109/95.311761 ↗
6. S.N. Khrain: IEEE Trans. Component Packaging A, 1996, vol. 19 (3), pp. 313–19.10.1109/95.536832 ↗
7. J.W. Yeh, S.Y. Yuan, and C.H. Peng: Mater. Sci. Eng. A, 1998, vol. 252, pp. 212–21.10.1016/S0921-5093(98)00677-7 ↗
8. J.W. Yeh, S.Y. Yuan, and C.H. Peng: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 2503–12.10.1007/s11661-999-0259-6 ↗
9. J.W. Yeh, K.S. Liu, and H.S. Chu: Mater. Sci. Eng. A, 2000, vol. 277, pp. 25–32.10.1016/S0921-5093(99)00562-6 ↗
10. S. Chu, K.S. Liu, and J.W. Yeh: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 2587–96.10.1007/s11661-000-0203-2 ↗
11. H.S. Chu, K.S. Liu, and J.W. Yeh: J. Mater. Res., 2001, vol. 16, pp. 1372–80.10.1557/JMR.2001.0192 ↗
12. R. Asthana and P.K. Rohatgi: J. Mater. Sci., 1991, vol. 10, pp. 230–34.
13. S.W. Lee, J.W. Yeh, and Y.S. Liao: Adv. Eng. Mater., 2004, vol. 6, pp. 936–43.10.1002/adem.200400107 ↗
14. S.W. Lee, H.Y. Wang, Y.L. Chen, J.W. Yeh, and C.F. Yang: Adv. Eng. Mater., 2004, vol. 6, pp. 948–52.10.1002/adem.200400117 ↗
15. A.G. Every, Y. Tzou, D.P.H. Hasselman, and R. Raj: Acta Metall. Mater., 1992, vol. 40, pp. 123–29.10.1016/0956-7151(92)90205-S ↗
16. David Jiles: Introduction to the Electronic Properties of Materials, 1st ed., Chapman & Hall, London, 1994, pp. 48–49.10.1007/978-1-4615-2582-0 ↗
17. J.R. Davis, P. Allen, S.R. Lampman, and T.B. Zorc: ASM Metals Handbook, 10th ed., ASM INTERNATIONAL, Metals Park, OH, 1990, vol. 2, pp. 1156–58.
18. G.M. Gladysz and K.K. Chawla: Compos. Part A-Appl. Sci., 2001, vol. 32, pp. 173–78.10.1016/S1359-835X(00)00144-5 ↗
19. P.S. Turner: J. Res. NBS, 1946, vol. 37, p. 239.
20. S.Y. Chang, S.J. Lin, and Merton C. Flemings: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 291–98.10.1007/s11661-000-0073-7 ↗
21. Z.K. Chen and K. Sawa: IEEE Trans. Component Packaging A, 1998, vol. 21 (2), pp. 310–22.10.1109/95.705480 ↗
22. Z.K. Chen and K. Sawa: IEEE Proc. 18th Int. Conf. on Electrical Contacts, Chicago, IL, 1996, pp. 238–51.
23. J. Swingler and J.W. McBride: IEEE Proc. 43rd IEEE Holm Conf. on Electrical Contacts, Philadelphia, PA, 1997, pp. 238–45.
24. J. Swingler and J.W. McBride: IEEE Trans. Component Packaging A, 1999, vol. 22 (1), pp. 27–37.10.1109/6144.759350 ↗
25. S. Kang and C. Brecher: IEEE Trans. Component Hybr., 1989, vol. 12 (1), pp. 32–38.10.1109/33.19009 ↗
26. M.Z. Rong and Q.P. Wang: IEEE Proc. 39th IEEE Holm Conf. on Electrical Contacts, Pittsburgh, PA, 1993, pp. 33–36.
27. J.A. Dean: Lange’s Handbook of Chemistry, 13th ed., McGraw-Hill Book Co., Singapore, 1987, pp. 4.61, 4.106, and 4.123.
28. H. Nouri, T.S. Davies, and J. Head: IEEE Proc. 44th IEEE Holm Conf. on Electrical Contacts, Arlington, VA, 1998, pp. 207–13.