journal article·2012-09Open access

Twinning-Slip Transitions in Mg AZ31B

Kun Piao, Kwansoo Chung, Myoung-Gyu Lee, Robert H. Wagoner

Abstract

Many metals, particularly ones with hexagonal close-packed (HCP) crystal structures, undergo deformation by combinations of twinning and slip, the proportion of which depends on variables such as the temperature and strain rate. The typical techniques to reveal such mechanisms rely on metallography, X-ray diffraction, or electron optics. Simpler, faster, less expensive mechanical tests were developed in the current work and applied to Mg AZ31B. The curvature of compressive stress–strain plots over a fixed strain range was found to be a consistent indicator of twinning magnitude, independent of the temperature and strain rate. The relationship between the curvature and areal fraction of twins was determined. The transition temperatures determined based on stress–strain curvature were consistent with the ones determined by metallographic analysis and flow stresses, and the results depended on the strain rate according to the Zener-Hollomon parameter, a critical value for which was measured. The transition temperature was found to depend significantly on the grain size, a relationship for which was established. Finally, it was shown that the transition temperature can be determined consistently, and much faster, using a single, novel “step-temperature” test.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Hydrogen Storage and Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (69)

Show source-provided references
1. C.S. Roberts: Magnesium and Its Alloys, Wiley, New York, NY, 1960.
2. S.R. Agnew: JOM, 2004, vol. 56, no. 5, pp. 20–21.10.1007/s11837-004-0120-8 ↗
3. C.J. Bettles and M.A. Gibson: JOM, 2005, vol. 57, no. 5, pp. 46–50.10.1007/s11837-005-0095-0 ↗
4. O. Duygulu and S.R. Agnew: Magnesium Technology 2002, H. Kaplan, ed., TMS, Warrendale, PA, 2003, pp. 237–42.
5. L. Wu, R. Agnew, Y. Ren, D.W. Brown, B. Clausen, G.M. Stoica, H.R. Wenk, and P.K. Liaw:. Mater. Sci. Eng. A, 2010, vol. 527, pp. 7057–67.10.1016/j.msea.2010.07.047 ↗
6. A.A. Luo: Int. Mater. Rev., 2004, vol. 49, no. 1, pp. 13–30.10.1179/095066004225010497 ↗
7. S.R. Agnew and O. Duygulu: Int. J. Plastic., 2005, vol. 21, pp. 1161–93.10.1016/j.ijplas.2004.05.018 ↗
8. X.Y. Lou, M. Li, R.K. Boger, and S.R. Agnew: Int. J. Plastic., 2007, vol. 23, pp. 44–86.10.1016/j.ijplas.2006.03.005 ↗
9. A. Beck: Technology of Magnesium and its Alloys, Kynock Press, London, U.K. 1943.
10. J.P. Nobre, U. Noster, M. Kornmeier, A. Morão Dias, and B. Scholtes: Key Eng. Mater., 2002, vols. 230–232, pp. 267–70.10.4028/www.scientific.net/KEM.230-232.267 ↗
11. R. Von Mises: Z. Angew. Math. Mech., 1928, vol. 8, pp. 161–85.10.1002/zamm.19280080302 ↗
12. G.I. Taylor: J. Inst. Metals, 1938, vol. 62, p. 307.
13. S.R. Agnew and O. Duygulu: Magnesium Technology 2004, A.A. Luo, ed., TMS, Warrendale, PA, 2004, pp. 61–65.
14. U.F. Kocks and D.G. Westlake: Trans. TMS-AIME, 1967, vol. 239, pp. 1107–09.
15. S.R. Agnew, M.H. Yoo, and C.N. Tome: Acta Mater., 2001, vol. 49, pp. 4277–89.10.1016/S1359-6454(01)00297-X ↗
16. M.H. Yoo, J.R. Morris, K.M. Ho, and S.R. Agnew: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 813–17.10.1007/s11661-002-0150-1 ↗
17. R.E. Reed-Hill and R. Abbaschian: Physical Metallurgy Principles, 3rd ed., PWS Pub. Company, Boston, MA, 1994.
18. R.W. Hertzberg: Deformation and Fracture Mechanics of Engineering Materials, 4th ed., Wiley, New York, NY, 1996.
19. M. Li: Department of Material Science and Engineering, The Ohio State University, Columbus, OH, 2006.
20. B.C. Wonsiewicz and W.A. Backofen: Trans. TMS-AIME, 1967, vol. 239, pp. 1422–31.
21. T. Obara, H. Yoshiinga, and S. Morozumi: Acta Mater., 1973, vol. 21, pp. 845–53.10.1016/0001-6160(73)90141-7 ↗
22. H. Yoshinaga and R. Horiuchi: Trans. JIM, 1963, vol. 4, pp. 134–41.10.2320/matertrans1960.4.134 ↗
23. J.F. Stohr and J.P. Poirier: Phil. Mag., 1972, vol. 25, pp. 1313–29.10.1080/14786437208223856 ↗
24. M.A. Meyers, O. Vohringer, and V.A. Lubarda: Acta Mater., 2001, vol. 49, pp. 4025–39.10.1016/S1359-6454(01)00300-7 ↗
25. M.M. Avedesion and H. Baker: ASM Specialty Handbook: Magnesium and Magnesium Alloys, ASM International, Materials Park, OH, 1999.
26. J.W. Christian and S. Mahajan: Progr. Mater. Sci., 1995, vol. 39, pp. 1–157.10.1016/0079-6425(94)00007-7 ↗
27. E. El-Danaf, S.R. Kalidindi, and R.D. Doherty: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1223–33.10.1007/s11661-999-0272-9 ↗
28. S. Asgari, E. El-Danaf, S.R. Kalidindi, and R.D. Doherty: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 1781–95.10.1007/s11661-997-0109-3 ↗
29. E. El-Danaf, S.R. Kalidindi, and R.D. Doherty: Int. J. Plastic., 2001, vol. 17, pp. 1245–65.10.1016/S0749-6419(00)00090-5 ↗
30. S. Mahajan and D.F. Williams: Int. Metall. Rev., 1973, vol. 18, pp. 43–61.10.1179/095066073790137304 ↗
31. A.A. Salem, S.R. Kalidindi, and R.D. Doherty: Scripta Mater., 2002, vol. 46, pp. 419–23.10.1016/S1359-6462(02)00005-2 ↗
32. A.A. Salem, S.R. Kalidindi, and R.D. Doherty: Acta Mater., 2003, vol. 51, pp. 4225–37.10.1016/S1359-6454(03)00239-8 ↗
33. A.A. Salem, S.R. Kalidindi, R.D. Doherty, S.L. Semiatin: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 259–68.10.1007/s11661-006-0171-2 ↗
34. D.R. Chichili, K.T. Ramesh, and K.J. Hemker: Acta Mater., 1998, vol. 46, pp. 1025–43.10.1016/S1359-6454(97)00287-5 ↗
35. S.G. Song, and G.T. Gray: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 2665–75.10.1007/BF02669423 ↗
36. A.S. Khan, A. Pandey, T. Gnäupel-Herold, and R.K. Mishra: Int. J. Plastic., 2011, vol. 27, pp. 688–706.10.1016/j.ijplas.2010.08.009 ↗
37. L. Remy: Acta Mater., 1978, vol. 26, pp. 443–51.10.1016/0001-6160(78)90170-0 ↗
38. M.R. Barnett, Z. Keshavarz, A.G. Beer, and D. Atwell: Acta Mater., 2004, vol. 52, pp. 5093–103.10.1016/j.actamat.2004.07.015 ↗
39. M.R. Barnett: Mater. Sci. Eng. A, 2007, vol. 464, pp. 1–7.10.1016/j.msea.2006.12.037 ↗
40. L. Jiang, J. Jonas, A. Luo, A. Sachdev, and S. Godet: Mater. Sci. Eng. A, 2007, vols. 445–446, pp. 302–09.10.1016/j.msea.2006.09.069 ↗
41. O. Muransky, M.R. Barnett, D.G. Carr, S.C. Vogel, and E.C. Oliver: Acta Mater., 2010, vol. 58, pp. 1503–17.10.1016/j.actamat.2009.10.057 ↗
42. C.S. Barrett and C.T. Haller: Met. Tech., 1946, vol. 13 (8), p. 2103.
43. Y.N. Wang and J.C. Huang: Acta Mater., 2007, vol. 55, pp. 897–905.10.1016/j.actamat.2006.09.010 ↗
44. L. Jiang, J. Jonas, R. Mishra, A. Luo, A. Sachdev, S. Godet: Acta Mater., 2007, vol. 55, pp. 3899–3910.10.1016/j.actamat.2007.03.006 ↗
45. Z. Keshavarz and M.R. Barnett: Scripta Mater., 2006, vol. 55, pp. 915–18.10.1016/j.scriptamat.2006.07.036 ↗
46. M.D. Nave and M.R. Barnett: Scripta Mater., 2004, vol. 51, pp. 881–85.10.1016/j.scriptamat.2004.07.002 ↗
47. M.R. Barnett, M.D. Nave, and C.J. Bettles: Mater. Sci. Eng. A, 2004, vol. 386, pp. 205–11.10.1016/S0921-5093(04)00942-6 ↗
48. A. Jain, O. Duygulu, D.W. Brown, C.N. Tomé, and S.R. Agnew: Mater. Sci. Eng. A, 2008, vol. 486, pp. 545–55.10.1016/j.msea.2007.09.069 ↗
49. S.R. Agnew, C. Tome, D. Brown, T. Holden, and S. Vogel: Scripta Mater., 2003, vol. 48, pp. 1003–08.10.1016/S1359-6462(02)00591-2 ↗
50. B. Clausen, C.N. Tome, D.W. Brown, and S.R. Agnew: Reorient. Acta Mater., 2008, vol. 56, pp. 2456–68.10.1016/j.actamat.2008.01.057 ↗
51. L. Wu, A. Jain, D.W. Brown, G.M. Stoica, S.R. Agnew, B. Clausen, D.E. Fielden, and P.K. Liaw: Acta Mater., 2008, vol. 56, pp. 3699–3707.10.1016/j.actamat.2008.04.006 ↗
52. O. Muransky, D.G. Carr, P. Šittner, and E.C. Oliver: Int. J. Plastic., 2009, vol. 25, pp. 1107–27.10.1016/j.ijplas.2008.08.002 ↗
53. R.K. Boger, R.H. Wagoner, F. Barlat, M.G. Lee, and K. Chung: Int. J. Plastic., 2005, vol. 21, no. 12, pp. 2319–43.10.1016/j.ijplas.2004.12.002 ↗
54. Z. Tan, C. Magnusson, and B. Persson: Mater. Sci. Eng. A, 1994, vol. 183, pp. 31–38.10.1016/0921-5093(94)90887-7 ↗
55. T. Kuwabara, K. Nagata, and T. Nakako: Measurement and Analysis of the Bauschinger Effect of Sheet Metals Subjected to In-Plane Stress Reversals, AMPT’01, University Carlos III de Madrid, Madrid, Spain, 2001.
56. J. Cao, W. Lee, H.S. Cheng, M. Seniw, H.-P. Wang, and K. Chung: Int. J. Plastic., 2009, vol. 25, pp. 942–72.10.1016/j.ijplas.2008.04.007 ↗
57. M. Li, X.Y. Lou, J.H. Kim, and R.H. Wagoner: Int. J. Plastic., 2010, vol. 26, pp. 820–58.10.1016/j.ijplas.2009.11.001 ↗
58. J.H. Kim, J.H. Sung, and R.H. Wagoner: Int. J. Plastic., 2011, vol. 27, pp. 1658–76.10.1016/j.ijplas.2011.02.009 ↗
59. J.H. Sung, J.H. Kim, and R.H. Wagoner: Int. J. Plastic., 2010, vol. 26, pp. 1746–71.10.1016/j.ijplas.2010.02.005 ↗
60. L. Sun and R.H. Wagoner: Int. J. Plastic., 2011, vol. 27, pp. 1126–44.10.1016/j.ijplas.2010.12.003 ↗
61. K. Piao, J.K. Lee, H.Y. Lim, and R.H. Wagoner: Tension/Compression Test of Mg AZ31B at Elevated Temperatures, in North American Deep Drawing Research Group, TMS, Windsor, CA. 2008.
62. K. Piao, J.K. Lee, J.H. Kim, H.Y. Kim, K. Chung, F. Barlat, and R.H. Wagoner, Int. J. Plastic., 2012, in press.
63. F.J. Polesak, III, P.E. Krajewski, B. Raeisinia, and S.R. Agnew, TMS-AIME, 2008, pp. 159–64.
64. AUSTEM Co., Ltd., Korea, 1993.
65. V. Balakrishnan: Measurement of In-Plane Bauschinger Effect in Metal Sheets, The Ohio State University, Columbus, OH, 1999.
66. ASTM-E562-08e1: Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count, 1999.
67. ASTM-E112-10: Standard Test Methods for Determining Average Grain Size, 2010.
68. C. Zener and J.H. Hollomon: J. Appl. Phys., 1944, vol. 15, pp. 22–32.10.1063/1.1707363 ↗
69. T. Obara, H. Yoshinga, and S. Morozumi: Acta Metall., 1973, vol. 21, pp. 845–53.10.1016/0001-6160(73)90141-7 ↗