journal article·2014-07

The Effect of Nd on the Tension and Compression Deformation Behavior of Extruded Mg-1Mn (wt pct) at Temperatures Between 298 K and 523 K (25 °C and 250 °C)

Ajith Chakkedath, Jan Bohlen, Sangbong Yi, Dietmar Letzig, Zhe Chen, Carl J. Boehlert

Publisher page

Abstract

The tension and compression deformation behavior of extruded magnesium-1 wt pct manganese alloys with nominally 0.3 wt pct (MN10) and 1 wt pct neodymium (MN11) was studied over the temperature range of 298 K to 523 K (25 °C to 250 °C). Nd additions to Mg alloys tend to reduce the strong basal texture exhibited by conventional wrought Mg alloys and this work was intended to study the effect of Nd on the deformation behavior of Mg alloys. Insitu tensile and compressive experiments were performed using a scanning electron microscopy, and electron backscatter diffraction was performed both before and after the deformation. A slip trace analysis technique was used to identify the distribution of the deformation systems as a function of strain, and based on this analysis and the texture of the undeformed samples, the critical resolved shear stress ratios between the deformation systems were estimated. In the case of MN11, the deformation behavior under tension at all temperatures was dominated by slip, while in compression, extension twinning was the major deformation mode. In tension at 323 K (50 °C), extension twinning, basal, prismatic 〈a〉, and pyramidal 〈c + a〉 slip were active in MN11. Much less extension twinning was observed at 423 K (150 °C), while basal slip and prismatic 〈a〉 slip were dominant and presented similar relative activities. At 523 K (250 °C), twinning was not observed, and basal slip controlled the deformation. With the reduction of Nd content, less slip deformation and more twinning were observed during the tensile deformation. However, like for MN11, the extent of twinning in MN10 decreased with increasing temperature and basal slip was the primary deformation mode at elevated temperatures. Extension twinning was the major deformation mode under compression for all test temperatures in MN10 and MN11. The tensile strength decreased with increasing temperature for both alloys, where MN10 was slightly stronger than MN11 at 323 K (50 °C), which was expected to be a result of the stronger basal texture exhibited by MN10 due to its lower Nd content. However, MN11 maintained its strength more at elevated temperatures compared with MN10, and this was explained to be a result of the greater Nd content.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Hydrogen Storage and Materials · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. M. Easton, A. Beer, M. Barnett, C. Davies, G. Dunlop, Y. Durandet, S. Blacket, T. Hilditch, and P. Beggs: JOM, 2008, vol. 60 (11), pp. 57-62.10.1007/s11837-008-0150-8 ↗
2. M. Bamberger and G. Dehm: Annu. Rev. Mater. Res., 2008, vol. 38, pp. 505-33.10.1146/annurev.matsci.020408.133717 ↗
3. B. L. Mordike and T. Ebert: Mater. Sci. Eng. A, 2001, vol. 302 (1), pp. 37-45.10.1016/S0921-5093(00)01351-4 ↗
4. H. Friedrich and S. Schumann: J. Mater. Process. Technol., 2001, vol. 117 (3), pp. 276-81.10.1016/S0924-0136(01)00780-4 ↗
5. I. Ulacia, N. V. Dudamell, F. Gálvez, S. Yi, M. T. Pérez-Prado, and I. Hurtado: Acta Mater., 2010, vol. 58 (8), pp. 2988-98.10.1016/j.actamat.2010.01.029 ↗
6. Y. Chino, M. Kado, and M. Mabuchi: Mater. Sci. Eng. A, 2008, vol. 494 (1), pp. 343-49.10.1016/j.msea.2008.04.059 ↗
7. Y. Chino, M. Kado, and M. Mabuchi: Acta Mater., 2008, vol. 56 (3), pp. 387-94.10.1016/j.actamat.2007.09.036 ↗
8. J. Bohlen, M. R. Nürnberg, J. W. Senn, D. Letzig, and S. R. Agnew: Acta Mater., 2007, vol. 55 (6), pp. 2101-12.10.1016/j.actamat.2006.11.013 ↗
9. S. Sandlöbes, S. Zaefferer, I. Schestakow, S. Yi, and R. González-Martínez: Acta Mater., 2011, vol. 59 (2), pp. 429-39.10.1016/j.actamat.2010.08.031 ↗
10. L. W. F. Mackenzie and M. O. Pekguleryuz: Scripta Mater., 2008, vol. 59 (6), pp. 665-68.10.1016/j.scriptamat.2008.05.021 ↗
11. N. Stanford, D. Atwell, and M. R. Barnett: Acta Mater., 2010, vol. 58 (20), pp. 6773-83.10.1016/j.actamat.2010.09.003 ↗
12. L. Jiang, J. J. Jonas, and R. Mishra: Mater. Sci. Eng. A, 2011, vol. 528 (21), pp. 6596-6605.10.1016/j.msea.2011.05.027 ↗
13. N. Stanford: Mater. Sci. Eng. A, 2010, vol. 527 (10), pp. 2669-77.10.1016/j.msea.2009.12.036 ↗
14. R. Cottam, J. Robson, G. Lorimer, and B. Davis: Mater. Sci. Eng. A, 2008, vol. 485 (1), pp. 375-82.10.1016/j.msea.2007.08.016 ↗
15. J. Bohlen, S. Yi, D. Letzig, and K. U. Kainer: Mater. Sci. Eng. A, 2010, vol. 527 (26), pp. 7092-98.10.1016/j.msea.2010.07.081 ↗
16. R. K. Mishra, A. K. Gupta, P. Rama Rao, A. K. Sachdev, A. M. Kumar, and A. A. Luo: Scripta Mater., 2008, vol. 59 (5), pp. 562-65.10.1016/j.scriptamat.2008.05.019 ↗
17. N. Stanford, D. Atwell, A. Beer, C. Davis, and M. R. Barnett: Scripta Mater., 2008, vol. 59 (7), pp. 772-75.10.1016/j.scriptamat.2008.06.008 ↗
18. J. D. Robson, A. M. Twier, G. W. Lorimer, and P. Rogers: Mater. Sci. Eng. A, 2011, vol. 528 (24), pp. 7247-56.10.1016/j.msea.2011.05.075 ↗
19. T. Al-Samman and X. Li: Mater. Sci. Eng. A, 2011, vol. 528 (10), pp. 3809-22.10.1016/j.msea.2011.01.080 ↗
20. C. J. Boehlert, Z. Chen, A. Chakkedath, I. Gutiérrez-Urrutia, J. Llorca, J. Bohlen, S. Yi, D. Letzig, and M. T. Pérez-Prado: Philos. Mag., 2013, vol. 93 (6), pp. 598-617.10.1080/14786435.2012.725954 ↗
21. E. A. Ball and P. B. Prangnell: Scripta Metall. Mater., 1994, vol. 31 (2), pp. 111-16.10.1016/0956-716X(94)90159-7 ↗
22. J. Jain, W. J. Poole, C. W. Sinclair, and M. A. Gharghouri: Scripta Mater., 2010, vol. 62 (5), pp. 301-04.10.1016/j.scriptamat.2009.11.024 ↗
23. C. J. Boehlert, Z. Chen, I. Gutiérrez-Urrutia, J. Llorca, and M.T. Pérez-Prado: Acta Mater., 2012, vol. 60 (4), pp. 1889-1904.10.1016/j.actamat.2011.10.025 ↗
24. ASTM International: Standard Test Methods for Determining Average Grain Size, ASTM E112-96E3, ASTM International, West Conshohocken, PA, 2004.
25. J. E. Hilliard: Metal Prog., 1964, vol. 85 (5), pp. 99-102.
26. C. J. Boehlert, H. Li, L. Wang, and B. Bartha: Adv. Mater. Process, 2010, vol. 168, pp. 41-45.
27. H.Li, D.E. Mason, T.R. Bieler, C.J. Boehlert, and M.A. Crimp: Acta Mater., 2013, vol. 61 (20), pp. 7555–67.10.1016/j.actamat.2013.08.042 ↗
28. M. T. Pérez-Prado, J. A. del Valle, and O. A. Ruano: Scripta Mater., 2004, vol. 50 (5), pp. 667-71.10.1016/j.scriptamat.2003.11.015 ↗
29. S.-Y. Chang, T. Nakagaido, S.-K. Hong, D.H. Shin, and T. Sato: Mater. Trans. JIM, 2001, vol. 42 (7), pp. 1332-38.10.2320/matertrans.42.1332 ↗
30. I. P. Moreno, T. K. Nandy, J. W. Jones, J. E. Allison, and T. M. Pollock: Scripta Mater., 2003, vol. 48 (8), pp. 1029-34.10.1016/S1359-6462(02)00595-X ↗
31. M. R. Barnett: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 1799-1806.10.1007/s11661-003-0146-5 ↗
32. E. W. Kelley and W. F. Hosford: Trans. Met. Soc. AIME, 1968, vol. 242 (1), pp. 5-13.
33. R. E. Reed-Hill and W. D. Robertson: Acta Metall., 1957, vol. 5 (12), pp. 717-27.10.1016/0001-6160(57)90074-3 ↗
34. R. E. Reed-Hill and W. D. Robertson: J. Metals Trans. AIME, 1957, vol. 220, pp. 496-502.
35. A. Chapuis and J. H. Driver: Acta Mater., 2011, vol. 59 (5), pp. 1986-94.10.1016/j.actamat.2010.11.064 ↗
36. C. Guillemer, M. Clavel, and G. Cailletaud: Int. J. Plast., 2011, vol. 27 (12), pp. 2068-84.10.1016/j.ijplas.2011.06.002 ↗
37. H.L. Kim, J.S. Park, and Y.W. Chang: Mater. Sci. Eng. A, 2012, vol. 540, pp. 198-206.10.1016/j.msea.2012.01.126 ↗
38. E. Schmid: Proc. Int’l. Cong. Appl. Mech. Delft, 1924, p. 342.
39. E. Schmid and W. Boas: Plasticity of Crystals: With Special Reference to Metals, Chapman and Hall, London, 1935.
40. M. R. Barnett, Z. Keshavarz, A. G. Beer, and X. Ma: Acta Mater., 2008, vol. 56 (1), pp. 5-15.10.1016/j.actamat.2007.08.034 ↗
41. S. Godet, L. Jiang, A. A. Luo, and J. J. Jonas: Scripta Mater., 2006, vol. 55 (11), pp. 1055-58.10.1016/j.scriptamat.2006.07.059 ↗
42. Seong-Gu Hong, Sung Hyuk Park, and Chong Soo Lee: Acta Mater., 2010, vol. 58 (18), pp. 5873-85.10.1016/j.actamat.2010.07.002 ↗
43. S. Mu, J. J. Jonas, and G. Gottstein: Acta Mater., 2012, vol. 60 (5), pp. 2043-53.10.1016/j.actamat.2012.01.014 ↗
44. C. N. Tomé, I. J. Beyerlein, J. Wang, and R. J. McCabe: JOM, 2011, vol. 63 (3), pp. 19-23.10.1007/s11837-011-0038-x ↗
45. I. J. Beyerlein and C. N. Tomé: Proc. R. Soc. A Math. Phys. Eng. Sci., 2010, vol. 466 (2121), pp. 2517-44.10.1098/rspa.2009.0661 ↗