journal article·2018-05

Linear Friction Welding of Dissimilar Materials 316L Stainless Steel to Zircaloy-4

P. Wanjara, B. S. Naik, Q. Yang, X. Cao, J. Gholipour, D. L. Chen

Publisher page

Abstract

In the nuclear industry, there are a number of applications where the transition of stainless steel to Zircaloy is of technological importance. However, due to the differences in their properties there are considerable challenges associated with developing a joining process that will sufficiently limit the heat input and welding time—so as to minimize the extent of interaction at the joint interface and the resulting formation of intermetallic compounds—but still render a functional metallurgical bond between these two alloys. As such, linear friction welding, a solid-state joining technology, was selected in the present study to assess the feasibility of welding 316L stainless steel to Zircaloy-4. The dissimilar alloy welds were examined to evaluate their microstructural characteristics, microhardness evolution across the joint interface, static tensile properties, and fatigue behavior. Microstructural observations revealed a central intermixed region and, on the Zircaloy-4 side, dynamically recrystallized and thermomechanically affected zones were present. By contrast, deformation on the 316L stainless steel side was limited. In the intermixed region a drastic change in the composition was observed along with a local increase in hardness, which was attributed to the presence of intermetallic compounds, such as FeZr3 and Cr2Zr. The average yield (316 MPa) and ultimate tensile (421 MPa) strengths met the minimum strength properties of Zircaloy-4, but the elongation was relatively low (~ 2 pct). The tensile and fatigue fracture of the welds always occurred at the interface in the mode of partial cohesive failure.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Hydrogen embrittlement and corrosion behaviors in metals · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (64)

Show source-provided references
1. [1] E. Gutsmiedl and A. Scheuer: Physica B Condens Matter, 2002, Vol. 311, pp. 182–190.10.1016/S0921-4526(01)01135-8 ↗
2. [2] F. Cattant, D. Crusset and D. Féron, Mater. Today, 2008, Vol. 11, pp. 32–37.10.1016/S1369-7021(08)70205-0 ↗
3. [3] G. Perona, R. Sesini, W. Nicodemi and R. Zoja, J. Nucl. Mater., 1966, Vol. 18, pp. 278–291.10.1016/0022-3115(66)90169-3 ↗
4. [4] H.I. Shaaban, F.H. Hammad and J.L. Baron, J. Nucl. Mater., 1978, Vol. 71, pp. 277–285.10.1016/0022-3115(78)90425-7 ↗
5. [5] P.Gr. Lucuta, I. Pătru and F. Vasiliu, J. Nucl. Mater., 1981, Vol. 99, pp. 154–164.10.1016/0022-3115(81)90184-7 ↗
6. [6] M. Taouinet, S. Lebaili and N. Souami, Physics Procedia, 2009, Vol. 2, pp. 1231–1239.10.1016/j.phpro.2009.11.086 ↗
7. [7] A.A. Abou-Zahra and F.H. Hammad, Materialwissenschaft und Werkstofftechnik, 1979, Vol. 10, pp. 349–353.10.1002/mawe.19790101006 ↗
8. [8] H.I. Shaaban, F.H. Hammad and J.L. Baron, J. Nucl. Mater., 1978, Vol. 78, pp. 431–433.10.1016/0022-3115(78)90467-1 ↗
9. [9] M. Ahmad, J.I. Akhter, Q. Zaman, M.A. Shaikh, M. Akhtar, M. Iqbal and E. Ahmed, J. Nucl. Mater., 2003, Vol. 317, pp. 212–216.10.1016/S0022-3115(03)00085-0 ↗
10. [10] J.I. Akhter, M. Ahmad, M. Iqbal, M. Akhtar and M.A. Shaikh, J. Alloys Compd., 2005, Vol. 399, pp. 96–100.10.1016/j.jallcom.2005.03.009 ↗
11. [11] K. Bhanumurthy, J. Krishnan, G.B. Kale, R.K. Fotedar, A.R. Biswas and R.N. Arya, J. Mater. Process. Technol., 1995, Vol. 54, pp. 322–325.10.1016/0924-0136(94)01782-4 ↗
12. A. Munis, M. Ahmed, J.I. Akhter, G. Ali, and N.H. Tariq: Proceedings of the 10th International Symposium on Advanced Materials, Rawalpindi, Pakistan, 2007, pp. 157–59.
13. [13] D. Mukherjee and J.P. Panakkal, J. Mater. Sci. Lett., 1995, Vol. 14, pp. 1383–1385.10.1007/BF00270736 ↗
14. [14] M. Ahmad, J. I. Akhter, M. Akhtar and M. Iqbal, J. Mater. Sci., 2007, Vol. 42, pp. 328–331.10.1007/s10853-006-1028-1 ↗
15. [15] M. Ahmad, J.I. Akhter, M.A. Shaikh, M. Akhtar, M. Iqbal and M.A. Chaudhry, J. Nucl. Mater., 2002, Vol. 301, pp. 118–121.10.1016/S0022-3115(01)00757-7 ↗
16. [16] T.H. Hazlett, Welding J., 1962, Vol. 41, pp. 448s–450s.
17. [17] A.R. Shankar, S.S. Babu, M. Ashfaq, U.K. Mudali, K.P. Rao, N. Saibaba and B. Raj, J. Mater. Eng. Perform., 2009, Vol. 18, pp. 1272–1279.10.1007/s11665-009-9376-z ↗
18. [18] J. Kilbride and D.F. Adams, Weld. Met. Fab., 1971, Vol. 39, pp. 26–35.
19. [19] J.C. Stinville, F. Bridier, D. Ponsen, P. Wanjara and P. Bocher, Int. J. Fatigue, 2015, Vol. 70, pp. 278–288.10.1016/j.ijfatigue.2014.10.002 ↗
20. [20] P. Wanjara, E. Dalgaard, J. Gholipour, X. Cao, J. Cuddy and J.J. Jonas, Metall. Mater. Trans. A, 2014, Vol. 45, pp. 5138–5157.10.1007/s11661-014-2475-y ↗
21. [21] E. Dalgaard, P. Wanjara, J. Gholipour and J.J. Jonas, Can. Metall. Q., 2012, Vol. 51, pp. 269–276.10.1179/1879139512Y.0000000014 ↗
22. [22] E. Dalgaard, P. Wanjara, J. Gholipour, X. Cao and J.J. Jonas, Acta Mater., 2012, Vol. 60, pp. 770–780.10.1016/j.actamat.2011.04.037 ↗
23. [23] M. Smith, L. Bichler, J. Gholipour and P. Wanjara, Int. J. Adv. Manuf. Tech., 2017, Vol. 90, pp. 1931–1946.10.1007/s00170-016-9515-2 ↗
24. [24] A. Chamanfar, M. Jahazi, J. Gholipour, P. Wanjara and S. Yue, Mater. Charact., 2015, Vol. 104, pp. 149–161.10.1016/j.matchar.2015.04.011 ↗
25. [25] A. Chamanfar, M. Jahazi, J. Gholipour, P. Wanjara and S. Yue, Metall. Mater. Trans. A, 2013, Vol. 44, pp. 4230–4238.10.1007/s11661-013-1767-y ↗
26. [26] O.T. Ola, O.A. Ojo, P. Wanjara and M.C. Chaturvedi, Adv. Mater. Res., 2011, Vol. 278, pp. 446–453.10.4028/www.scientific.net/AMR.278.446 ↗
27. [27] A. Chamanfar, M. Jahazi, J. Gholipour, P. Wanjara and S. Yue, Mater. Sci. Eng. A, 2012, Vol. 555, pp. 117– 130.10.1016/j.msea.2012.06.041 ↗
28. [28] K.R. Vishwakarma, O.A. Ojo, P. Wanjara and M.C. Chaturvedi, JOM, 2014, Vol. 66, pp. 2525–2534.10.1007/s11837-014-0938-7 ↗
29. [29] O.T. Ola, O.A. Ojo, P. Wanjara and M.C. Chaturvedi, Metall. Mater. Trans. A, 2011, Vol. 42, pp. 3761–3777.10.1007/s11661-011-0774-0 ↗
30. [30] A. Chamanfar, M. Jahazi, J. Gholipour, P. Wanjara and S. Yue, Mater. Des., 2012, Vol. 36, pp. 113–122.10.1016/j.matdes.2011.11.007 ↗
31. [31] O.T. Ola, O.A. Ojo, P. Wanjara and M.C. Chaturvedi, Metall. Mater. Trans. A, 2012, Vol. 43, pp. 921–933.10.1007/s11661-011-0928-0 ↗
32. [32] P. Wanjara, E. Dalgaard, J. Gholipour and J. Larose, Mater. Sci. Forum, 2012, Vol. 706-709, pp. 3022–3027.10.4028/www.scientific.net/MSF.706-709.3022 ↗
33. [33] P. Wanjara, E. Dalgaard, G. Trigo, C. Mandache, G. Comeau and J. J. Jonas, Can. Metall. Q., 2011, Vol. 50, pp. 350–359.10.1179/000844311X13112418194644 ↗
34. [34] E. Dalgaard, P. Wanjara, G. Trigo, M. Jahazi, G. Comeau and J. J. Jonas, Can. Metall. Q., 2011, Vol. 50, pp. 360–370.10.1179/000844311X13112418194671 ↗
35. [35] I. Bhamji, M. Preuss, R.J. Moat, P.L. Threadgill and A.C. Addison, Sci. Technol. Weld. Joining, 2012, Vol. 17, pp. 368–374.10.1179/1362171812Y.0000000017 ↗
36. [36] P. Wanjara, J. Gholipour, K. Watanabe, K. Nezaki, Y. Tian and M. Brochu, Mater. Sci. Forum, 2017, Vol. 879, 2072–2077.10.4028/www.scientific.net/MSF.879.2072 ↗
37. [37] W. Li, A. Vairis, M. Preuss and T. Ma, International Materials Reviews, 2016, Vol. 61, pp. 71-100.10.1080/09506608.2015.1109214 ↗
38. [38] P. Wanjara and M. Jahazi, Metall. Mater. Trans. A, 2005, Vol. 36, pp. 2149–2164.10.1007/s11661-005-0335-5 ↗
39. ASTM E8M-16a, Standard test methods for tension testing of metallic materials (Metric).
40. ASTM E466-15: Standard practice for conducting force controlled constant amplitude axial fatigue tests of metallic materials.
41. ASME BPVC-III-2017: ASME boiler & pressure vessel code—section iii—rules for construction of nuclear power plant components.
42. ASTM E112-13: Standard test methods for determining average grain size.
43. [43] H.M Chung and T.F Kassner, J. Nucl. Mater. 84 (1979) 327–339.10.1016/0022-3115(79)90172-7 ↗
44. [44] R.K. Desu, H.N. Krishnamurthy, A. Balu, A.K. Gupta and S.K. Singh, J. Mater. Res. Technol., 2016, Vol. 5, pp. 13–20.10.1016/j.jmrt.2015.04.001 ↗
45. [45] A. Vairis and M. Frost, Wear (Switzerland), 1998, Vol. 217, pp. 117–131.
46. [46] E. Dalgaard, F. Coghe, L. Rabet, M. Jahazi, P. Wanjara and J.J. Jonas, Adv. Mater. Res., 2010, Vol. 89-91, pp. 124–129.10.4028/www.scientific.net/AMR.89-91.124 ↗
47. K.-D. Liss, U. Garbe, H. Li, T. Schambron, J.D. Almer, K. Yan: Adv. Eng. Mater, 11 (2009), 637–640.10.1002/adem.200900094 ↗
48. [48] C. Chauvy, P. Barbéris and F. Montheillet, Mater. Sci. Forum, 2004, Vol. 467-470, pp. 1151–1156.10.4028/www.scientific.net/MSF.467-470.1151 ↗
49. R.E. Logé, Y.B. Chastel, M.Y. Perrin, J.W. Signorelli, and R.A. Lebensohn: in Hot Extrusion of Zircaloy-4 Tubes: Induced Crystallographic Textures and Influence of the Initial Microstructure, Mathematical Modeling in Metal Processing and Manufacturing, P. Martin, W.J. Liu, S. MacEwen, Y. Verreman and J. Goldak, eds., The Metallurgical Society of CIM, Canada, 2000.
50. L. Whitmarsh: Review of Zircaloy-2 and Zircaloy-4 properties relevant to NS Savannah reactor design, ORNL-3281, Oak Ridge National Laboratory, Oak Ridge, 1962.
51. [51] B.M. Pande and R.P. Agarwala, J. Nucl. Mater., 1972, Vol. 42, pp. 43–48.10.1016/0022-3115(72)90005-0 ↗
52. [52] B.M. Pande, M.C. Naik and R.P. Agarwala, J. Nucl. Mater., 1968, Vol. 28, pp. 324–332.10.1016/0022-3115(68)90200-6 ↗
53. [53] C. Herzig and H. Eckseler, Zeit. Metal., 1979, Vol. 70, pp. 215–223.
54. ASM International Handbook Committee: Metals Handbook. Vol. 1—Properties and Selection: Irons, Steels, and High-Performance Alloys, 10th ed., ASM International, Metals Park, OH, 1990.10.31399/asm.hb.v01.9781627081610 ↗
55. ASM International Handbook Committee: Metals Handbook. Vol. 2—Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, 10th ed., ASM International, Metals Park, OH, 1990.
56. C. Evans: Micromechanisms and Micromechanics of Zircaloy-4, Doctoral Thesis Imperial College, London, UK, 2014.
57. [57] J.H. Kim, M.H. Lee, B.K. Choi and Y.H. Jeong, J. Nucl. Sci. Technol., 2007, Vol. 44, pp. 1275–1280.10.1080/18811248.2007.9711371 ↗
58. [58] A. Macwan and D.L. Chen, Mater. Des., 2015, Vol. 84, pp. 261–269.10.1016/j.matdes.2015.06.104 ↗
59. [59] W. Xu, L. Liu, Y. Zhou, H. Mori and D.L. Chen, Mater. Sci. Eng. A, 2013, Vol. 563, pp. 125–132.10.1016/j.msea.2012.11.049 ↗
60. V.K. Patel, D.L. Chen, and S.D. Bhole: Theor. Appl. Mech. Lett. 2014, Vol. 4, pp. 041005-1–8.10.1063/2.1404105 ↗
61. [61] S.H. Chowdhury, D.L. Chen, S.D. Bhole, X. Cao and P. Wanjara, Mater. Sci. Eng. A, 2013, Vol. 562, pp. 53–60.10.1016/j.msea.2012.11.039 ↗
62. [62] A.D. Pelton, L. Leibowitz and R.A. Blomquist, J. Nucl. Mater., 1993, Vol. 201, pp. 218–224.10.1016/0022-3115(93)90176-Y ↗
63. [63] K. Zeng, M. Hämäläinen and R. Luoma, Z. Metallkd., 1993, Vol. 84, pp. 23–28.
64. [64] J. Bodega, J.F. Fernández, F. Leardini, J.R. Ares and C. Sánchez, J. Phys. Chem. Solids, 2011, Vol. 72, pp. 1334–1342.10.1016/j.jpcs.2011.08.004 ↗