journal article·2016-06Open access

Investigation on the Behavior of Austenite and Ferrite Phases at Stagnation Region in the Turning of Duplex Stainless Steel Alloys

J. Nomani, A. Pramanik, T. Hilditch, G. Littlefair

Abstract

This paper investigates the deformation mechanisms and plastic behavior of austenite and ferrite phases in duplex stainless steel alloys 2205 and 2507 under chip formation from a machine turning operation. SEM images and EBSD phase mapping of frozen chip root samples detected a build-up of ferrite bands in the stagnation region, and between 65 and 85 pct, more ferrite was identified in the stagnation region compared to austenite. SEM images detected micro-cracks developing in the ferrite phase, indicating ferritic build-up in the stagnation region as a potential triggering mechanism to the formation of built-up edge, as transgranular micro-cracks found in the stagnation region are similar to micro-cracks initiating built-up edge formation. Higher plasticity of austenite due to softening under high strain is seen responsible for the ferrite build-up. Flow lines indicate that austenite is plastically deforming at a greater rate into the chip, while ferrite shows to partition most of the strain during deformation. The loss of annealing twins and activation of multiple slip planes triggered at high strain may explain the highly plastic behavior shown by austenite.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels · Non-Destructive Testing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. 1. J. Nomani, A. Pramanik, T. Hilditch and G. Littlefair, Wear 2013, vol. 304, pp. 20-28.10.1016/j.wear.2013.04.008 ↗
2. 2. Jukka Paro, Hannu Hänninen and Veijo Kauppinen, Wear 2001, vol. 249, pp. 279-284.10.1016/S0043-1648(01)00570-1 ↗
3. 3. C. Carlborg, Proceedings of duplex stainless steel 1991, vol. 1, pp. 683-96.
4. 4. J. E Williams and E. C Rollason, J. Inst. Met. 1970, vol. 98, pp. 144-159.
5. Anon, (International Molybdenum Association: 2009).
6. 6. K. Cho and J. Gurland, MTA 1988, vol. 19, pp. 2027-2040.10.1007/BF02645206 ↗
7. 7. Johan Johansson and Magnus Odén, Metall. Mater. Trans. A 2000, vol. 31, pp. 1557-1570.10.1007/s11661-000-0166-3 ↗
8. 8. J. Johansson, M. Odén and X. H. Zeng, Acta Mater. 1999, vol. 47, pp. 2669-2684.10.1016/S1359-6454(99)00149-4 ↗
9. 9. Y. Motoyashiki, A. BrÜCkner-Foit and A. Sugeta, Fatigue Fract. Eng. Mater. Struct. 2007, vol. 30, pp. 556-564.10.1111/j.1460-2695.2007.01130.x ↗
10. 10. B. Dönges, A. Giertler, U. Krupp, C. P. Fritzen and H. J. Christ, J. Mater. Sci. Eng. A 2014, vol. 589, pp. 146-152.10.1016/j.msea.2013.09.098 ↗
11. 11. E. F. Rauch and M. Véron, Mater. Charact. 2014, vol. 98, pp. 1-9.10.1016/j.matchar.2014.08.010 ↗
12. 12. Y. Idell, G. Facco, A. Kulovits, M. R. Shankar and J. M. K. Wiezorek, Scripta Mater. 2013, vol. 68, pp. 667-670.10.1016/j.scriptamat.2013.01.025 ↗
13. 13. T Long, W Tang and AP Reynolds, Sci. Technol. Weld. Joining 2007, vol. 12, pp. 311-317.10.1179/174329307X197566 ↗
14. Z.W. Chen and S. Cui: in IOP Conference Series: Materials Science and Engineering, IOP Publishing, 2009, p. 012026.10.1088/1757-899X/4/1/012026 ↗
15. Mohamed N. A. Nasr, E. G. Ng and M. A. Elbestawi, Int. J Mach. Tools and Manufac. 2007, vol. 47, pp. 401-41110.1016/j.ijmachtools.2006.03.004 ↗
16. 16. C. Herrera, D. Ponge and D. Raabe, Acta Mater. 2011, vol. 59, pp. 4653-4664.;10.1016/j.actamat.2011.04.011 ↗
17. 17. J. A. Jimenez, M. Carsi, O. A. Ruano and F. Peñalba, J. Mater. Sci. 2000, vol. 35, pp. 907-915.10.1023/A:1004750424897 ↗
18. 18. D. A. Hughes and N. Hansen, Acta Mater. 1997, vol. 45, pp. 3871-3886.10.1016/S1359-6454(97)00027-X ↗
19. 19. S. Wroński, J. Tarasiuk, B. Bacroix, A. Baczmański and C. Braham, Mater. Charact. 2012, vol. 73, pp. 52-60.10.1016/j.matchar.2012.07.016 ↗
20. 20. Mukul Kumar, Adam J. Schwartz and Wayne E. King, J. Mater. Sci. Eng. A 2001, vol. 309–310, pp. 78-81.10.1016/S0921-5093(00)01771-8 ↗
21. 21. T Kruml and S Degallaix, Acta Mater. 1997, vol. 45, pp. 5145-5151.10.1016/S1359-6454(97)00178-X ↗
22. 22. Ehab El-Danaf, SuryaR Kalidindi and RogerD Doherty, Metall. Mater. Trans. A 1999, vol. 30, pp. 1223-1233.10.1007/s11661-999-0272-9 ↗
23. 23. Kazuaki Iwata and Kanji Ueda, Wear 1980, vol. 60, pp. 329-337.10.1016/0043-1648(80)90231-8 ↗
24. 24. J. Wallbank, Metals Technology 1979, vol. 6, pp. 145-153.10.1179/030716979803276426 ↗
25. 25. Johan J. Moverare and Magnus Odén, J. Mater. Sci. Eng. A 2002, vol. 337, pp. 25-38.10.1016/S0921-5093(02)00022-9 ↗
26. 26. Johan Moverare and Magnus Odén, Metall. Mater. Trans. A 2002, vol. 33, pp. 57-71.10.1007/s11661-002-0005-9 ↗
27. 27. S. Dolinsek, J. Mater. Process. Technol. 2003, vol. 133, pp. 63-70.10.1016/S0924-0136(02)00245-5 ↗
28. 28. A. Mateo, L. Llanes, L. Iturgoyen and M. Anglada, Acta Mater. 1996, vol. 44, pp. 1143-1153.10.1016/1359-6454(95)00197-2 ↗
29. 29. Karel Obrtlík, Tomásš Kruml and Jaroslav Polák, J. Mater. Sci. Eng. A 1994, vol. 187, pp. 1-9.10.1016/0921-5093(94)90325-5 ↗
30. 30. X. Feaugas, Acta Mater. 1999, vol. 47, pp. 3617-3632.10.1016/S1359-6454(99)00222-0 ↗
31. 31. V. Randle, Acta Mater. 1999, vol. 47, pp. 4187-4196.10.1016/S1359-6454(99)00277-3 ↗
32. 32. Peter Hedström, Tong-Seok Han, Ulrich Lienert, Jonathan Almer and Magnus Odén, Acta Mater. 2010, vol. 58, pp. 734-744.10.1016/j.actamat.2009.09.053 ↗