journal article·2016-07

Effect of Alloying Elements in Hot-Rolled Metastable β-Titanium Alloys. Part II: Mechanical Properties

Premkumar Manda, Uday Chakkingal, A. K. Singh

Publisher page

Abstract

This paper describes the tensile properties, flow and work-hardening behavior of four metastable β-titanium alloys Ti-5Al-5Mo-5V-3Cr (A1), Ti-5Al-3.5Mo-7.2V-3Cr (A2), Ti-5Al-5Mo-8.6V-1.5Cr (A3), and Ti-5Al-3.5Mo-5V-3.94Cr (A4) in α+β hot-rolled condition. The decreasing order of average strength parameters (σ YS and σ UTS) is A4, A2, A1, and A3. The maximum strength observed in alloy A4 is due to the presence of highest wt. fraction of Cr. The elongation is the maximum and minimum in alloys A3 and A4, respectively. These alloys display moderate to high percent in-plane anisotropy (A IP) and reasonably low anisotropic index (δ) values. Both the A IP and δ values are maximum and minimum in alloys A1 and A3, respectively. The yield locus plots also exhibit the presence of anisotropy due to relatively large differences in yield strength values along tension and compression directions. The flow behavior of alloys A1, A2, and A4 follows Swift equation, while the alloy A3 displays best fit with Holloman equation. The presence of prestrain (e 0) in hot-rolled materials before tensile testing has an important bearing on the flow curves of A1, A2, and A4 alloys. The instantaneous work-hardening rate curves of the alloys A1, A2, and A3 exhibit all the three typical stages (stage I, stage II, and stage III) in RD samples, while the alloy A4 shows the presence of only stage I and stage III. The 45 deg to RD and TD samples of alloys A1, A2, and A4 display only stage I. The stages I and III as well as I and II are present in alloy A3 in 45 deg to RD and TD samples, respectively. Dislocation-controlled strain hardening occurs in all the three stages of these alloys in the absence of stress-induced martensitic transformation (α″) and twinning. Slip is the predominant deformation mechanism during tensile testing. Three types of slip lines, i.e., planar, wavy, and intersecting have been observed close to fracture surfaces of post tensile-tested specimens.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Advanced materials and composites · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. 1. E.W. Collings, Physical Metallurgy of Titanium Alloys, American Society of Metals, OH (1984).
2. 2. R.R. Boyer and R. D. Briggs: J. Mater. Eng. Perform., 2005, vol. 14, pp. 681-8510.1361/105994905X75448 ↗
3. 3. R.R. Boyer, Beta titanium alloys in the 1990’s. TMS, Warrendale 1993, 335.
4. J.C. Williams: Titanium: Science and Technology. Plenum Press, New York, pp. 1433-94 (1973).
5. J.C. Williams: in Titanium and Titanium Alloys, Scientific and Technological Aspects, J.C. Williams and A.F. Belov, eds., Plenum Press, New York, 1982, ISBN 0-306-40191-6, pp. 1477–98.
6. 6. T.K. Nandy, A. Bhattacharjee, A.K. Singh and A.K. Gogia: Metals Mater. Processes, 2006, vol. 18, pp. 289-308.
7. 7. N.G. Jones, R.J. Dashwood, D. Dye, and M. Jackson: Mater. Sci. Eng. A, 2008, vol. 490, pp. 369-77.10.1016/j.msea.2008.01.055 ↗
8. 8. N.G. Jones, R.J. Dashwood, D. Dye, and M. Jackson: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 1944-54.10.1007/s11661-009-9866-5 ↗
9. R. Panza-Giosa. Ph.D Thesis, McMaster University, Canada, 2009.
10. 10. G. Lütjering, J.C. Williams, Titanium, second ed., Springer-Verlag, Berlin, Germany, 2007.
11. V.V. Tetyukhin: Proceedings of 13th Annual Titanium Conference, ITA, San Francisco CA, 1997.
12. 12. S. Veeck, D. Lee, R. Boyer and R. Briggs: J. Adv. Mater., 2005, vol. 37, pp. 40-45.
13. 13. N. Clement, A. Lenain and P.J. Jacques: J. Met., 2007, vol. 59, pp. 50-53.
14. V.N. Moiseev: in Titanium 95: Science and Technology, P.A. Blenkinsop, W.J. Evans, and H.M. Flower, eds., The Institute of Materials, Birmingham, 1995, pp. 1387–94.
15. C. Roubaud, T. Grosdidier, M. Phillippe, and Y. Combres: in Titanium 95: Science and Technology, P.A. Blenkinsop, W.J. Evans, and H.M. Flower, eds., The Institute of Materials, Birmingham, 1995, pp. 996–1003.
16. 16. T.W. Duerig, G.T. Terlinde and J.C. Williams: Metall. Mater. Trans. A, 1980, vol. 11A, pp. 1987-98.10.1007/BF02655118 ↗
17. T.W. Duerig and J.C. Williams: in Overview: Microstructure and Properties of Beta Titanium Alloys in the 1980’s, R.R. Boyer and H.W. Rosenberg, eds., AIME, New York, 1984.
18. 18. M. Jackson, R. Dashwood, L. Christodoulou, and H. Flower: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 1317-27.10.1007/s11661-005-0223-z ↗
19. 19. M. Jackson, N.G. Jones, D. Dye, and R.J. Dashwood: Mater. Sci. Engg. A, 2009, vol. 501, pp. 248-54.10.1016/j.msea.2008.09.071 ↗
20. 20. N.G. Jones, R.J. Dashwood, M. Jackson, and D. Dye: Acta Mater., 2009, vol. 57, pp. 3830-39.10.1016/j.actamat.2009.04.031 ↗
21. 21. S. Nag, R. Banerjee, R. Srinivasan, J.Y. Hwang, M. Harper, and H.L. Fraser: Acta Mater., 2009, vol. 57, pp. 2136-47.10.1016/j.actamat.2009.01.007 ↗
22. 22. P.J. Arrazola, A. Garay, L.M. Iriarte, M. Armendia, S. Marya, and F. Le Maitre: J. Mater Proc. Technol., 2009, vol. 209, pp. 2223-30.10.1016/j.jmatprotec.2008.06.020 ↗
23. J.C. Fanning and R.R. Boyer: in Titanium 2003: Science and Technology, vol. IV, G. Luetjering and J. Albrecht, eds., Wiley-VCH, Hamburg, 2003, pp. 2643–50.
24. 24. S.K. Kar, A. Ghosh, N. Fulzele, and A. Bhattacharjee: Mater. Charact., 2013, vol. 81, pp. 37-48.10.1016/j.matchar.2013.03.016 ↗
25. 25. P. Manda, P. Ghosal, U. Chakkingal, and A.K. Singh: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 2646-63.10.1007/s11661-015-2814-7 ↗
26. 26. N.G. Jones and M. Jackson: Mater. Sci. Technol, 2011, vol. 27, pp. 1025-32.10.1179/026708310X12668415533720 ↗
27. J.C. Fanning, S.L. Nyakana, K.M. Patterson, and McDaniel: in Titanium 2007: Science and Technology, vol. I, M. Niinomi, S. Akiyama, M. Hagiwara, M. Ikeda, and K. Maruyama, eds., The Japan Institute of Metals, Kyoto, 2007, pp. 499–502.
28. 28. S. Shekhar, R. Sarkar, S.K. Kar, and A. Bhattacharjee: Mater. Desi., 2015, vol.66, pp. 596-610.10.1016/j.matdes.2014.04.015 ↗
29. V. Venkatesh, M. Kamal, and J. Fanning: in Titanium 2007: Science and Technology, vol. I, M. Niinomi, S. Akiyama, M. Hagiwara, M. Ikeda, and K. Maruyama, eds., The Japan Institute of Metals, Kyoto, 2007, pp. 503–06.
30. 30. R.G. Wheeler, and D.R. Ireland: Electrochem. Technol., 1966, vol. 4, pp. 313–17.
31. 31. D. Lee and W.A. Backofen: Trans. AIME, 1996, vol. 236, pp. 1696–1704.
32. 32. D. Lee, J.H. Westbrook, and H. Conrad (Eds.), Science of Hardness Testing and its Research Applications, ASM International, Materials Park Ohio, 1973.
33. 33. J. H. Hollomon: Trans. AIME, 1945, vol. 162, pp. 268–90.
34. P. Ludwik: Elements der Technologischen Mechanik. Springer, Leipzig, 1909, p. 32.10.1007/978-3-662-40293-1 ↗
35. 35. H.W. Swift: J. Mech. Phys. Solids, 1952, vol. 1, pp. 1–18.10.1016/0022-5096(52)90002-1 ↗
36. S.R. Seagle and P.A. Russo: Material Engineering Institute-ASM International Course Material, Course 27, pp. 8–12.
37. 37. G.E. Dieter: Mechanical Metallurgy, McGraw-Hill Book Co., Singapore, 1988
38. A. Bhattacharjee: Ph.D Thesis, Indian Institute of Technology Kanpur, India, 2006.
39. 39. K.V. Jata, A.K. Hopkins, and R. J. Rioja: Mater. Sci. Forum, 1996, vol. 217-222, pp. 647-52.10.4028/www.scientific.net/MSF.217-222.647 ↗
40. 40. S. Banumathy, R.K. Mandal, and A.K. Singh: Int. J. Mat. Res., 2011, vol. 102, pp. 208-17.10.3139/146.110468 ↗
41. 41. Y.T. Wu, and C. H. Koo: Scripta Met., 1998, vol. 38, pp. 267-71.10.1016/S1359-6462(97)00431-4 ↗
42. 42. K.K. Mehta, P. Mukhopadhyay, R.K. Mandal, and A.K. Singh: Mater. Sci. Engg. A, 2014, vol. 613, pp. 71-81.10.1016/j.msea.2014.06.067 ↗
43. 43. E. Voce: J. Inst. Met., 1948, vol. 74, pp. 537–62.
44. 44. E. Voce: Metallurgia, 1955, vol. 51, pp. 219–26.
45. A. Bhattacharjee, V.A. Joshi, and A.K. Gogia: in Titanium 1999: Science and Technology, vol. I, I.V. Gorynin and S.S. Ushkov, eds., Saint-Petersburg, Russia, 1999, pp. 529–36.
46. 46. K.G. Samuel, and P. Rodriguez: J. Mater.Sci. 2005, vol. 40, pp. 5727-31.10.1007/s10853-005-1078-9 ↗
47. 47. D. C. Ludwigson: Metall. Trans., 1971, vol. 2, pp. 2825–28.10.1007/BF02813258 ↗
48. 48. C. Mondal, A.K. Singh, A.K. Mukhopadhyay, and K. Chattopadhyay: Mater. Sci. Engg. A, 2013, vol. 577, pp 87-100.10.1016/j.msea.2013.03.079 ↗
49. 49. M-H. Cai, C-Y. Lee, and Y-K. Lee: Scripta Mater., 2012, vol. 66, pp. 606-0910.1016/j.scriptamat.2012.01.015 ↗
50. 50. X. Min, X. Chen, S. Emura, and K. Tsuchiya: Scripta Mater., 2013, vol. 69, pp. 393-96.10.1016/j.scriptamat.2013.05.027 ↗