Effect of Composition on the Formation of Sigma during Single-Pass Welding of Mo-Bearing Stainless Steels
Source abstract
Abstract
A series of 64 Mo-bearing stainless steel compositions ranging from 0 to 10 wt pct Mo and over a broad range of Ni and Cr contents were analyzed over a variety of cooling rates. Alloys were created using the arc button melting process, and laser welds were prepared on each alloy at constant power and travel speeds ranging from 4.2 to 42 mm/s. The presence of the σ-sigma intermetallic was observed in several primary γ-austenite alloys with Mo contents ≥2.5 wt pct Mo and in several primary δ-ferrite alloys with Mo contents ≥6 wt pct Mo. However, its formation cannot be explained by the eutectic solidification reaction previously explored in this class of materials by the present authors. Instead, σ-sigma was determined to form by the eutectoid decomposition of δ-ferrite (δ → γ + σ) in the as-solidified arc melt buttons in both primary γ-austenite and primary δ-ferrite alloys. The high cooling rates in the laser welds (estimated to range from 104 °C/s to 105 °C/s) largely prevented this transformation from occurring, resulting in the retention of metastable δ-ferrite to room temperature. A correlation was observed between the composition of the δ-ferrite in the microstructure and the calculated onset temperature of sigma stability. By combining multicomponent liquidus projections and isothermal sections, a good correlation of δ-ferrite compositions that decompose to γ-austenite + σ-sigma upon cooling is presented. It is suggested that the absence of the chi (χ) phase, often observed in a similar composition range at high Mo contents, could be attributed to the extremely low carbon content in these alloys.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (77)
Show source-provided references
1. A. Garner: Corrosion (Houston), 1979, vol. 35 (3), pp. 108–1410.5006/0010-9312-35.3.108 ↗
2. A. Garner: Mater. Perform., 1982, vol. 21 (8), pp. 9–14
3. P.I. Marshall, T.G. Gooch: Corrosion (Houston), 1993, vol. 49 (6), pp. 514–2610.5006/1.3316080 ↗
4. M.B. Rockel, M. Renner: Werkst. Korros., 1984, vol. 35 (12), pp. 537–4210.1002/maco.19840351202 ↗
5. S.W. Banovic, J.N. DuPont, A.R. Marder: Sci. Technol. Weld. Join., 2002, vol. 17 (5), pp. 1–10
6. M.J. Cieslak, T.J. Headley, A.D. Romig Jr.: Metall. Trans. A, 1986, vol. 17A, pp. 2035–4710.1007/BF02645001 ↗
7. M.J. Perricone, J.N. DuPont: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 1267–8010.1007/s11661-006-1078-7 ↗
8. J.O. Nilsson, A. Wilson: Mater. Sci. Technol., 1993, vol. 9, pp. 545–5410.1179/mst.1993.9.7.545 ↗
9. S.H.C. Park, Y.S. Sato, H. Kokawa, K. Okamoto, S. Hirano, M. Inagaki: Scripta Mater., 2004, vol. 51, pp. 101–0510.1016/j.scriptamat.2004.04.001 ↗
10. T. Sourmail: Mater. Sci. Technol., 2001, vol. 17 (1), pp. 1–1410.1179/026708301101508972 ↗
11. C.C. Tseng, Y.Shen, S.W. Thompson, M.C. Mataya, G. Krauss: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 1147–5810.1007/BF02652290 ↗
12. J.O. Nilsson, P. Kenagas, T. Karlsson, A. Wilson: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 35–4510.1007/s11661-000-0050-1 ↗
13. T.H. Chen, K.L. Weng, J.R. Yang: Mater. Sci. Eng., 2002, vol. A338, pp. 259–7010.1016/S0921-5093(02)00093-X ↗
14. Y.S. Ahn, J.P. Kang: Mater. Sci. Technol., 2000, vol. 16 (4), pp. 382–8810.1179/026708300101507965 ↗
15. J.A. Brooks, M.I. Baskes, F.A. Greulich: Metall. Trans. A, 1991, vol. 22A, pp. 915–2610.1007/BF02659001 ↗
16. J.A. Brooks, A.W. Thompson: Int. Mater. Rev., 1991, vol. 36 (1), pp. 16–4410.1179/imr.1991.36.1.16 ↗
17. J.O. Nilsson: Mater. Sci. Technol., 1992, vol. 8 (8), pp. 685–70010.1179/mst.1992.8.8.685 ↗
18. C.H. Shek, G.J. Shen, J.K.L. Lai, B.J. Duggan: Mater. Sci. Technol., 1994, vol. 10 (4), pp. 306–1110.1179/mst.1994.10.4.306 ↗
19. J.M. Vitek and S.A. David: Weld. J., 1984, vol. 63 (8), pp. 246s–53s
20. J. Barcik: Mater. Sci. Technol., 1988, vol. 4 (1), pp. 5–1510.1179/mst.1988.4.1.5 ↗
21. A.S. Grot, J.E. Spruiell: Metall. Trans. A, 1975, vol. 6A, pp. 2023–3010.1007/BF03161827 ↗
22. J.K. Lai, J.R. Haigh: Weld. J., 1979, vol. 58 (1), pp. 1s–6s
23. J.M. Leitnaker: Weld. J., 1982, vol. 61 (1), pp. 9s–12s
24. J.E. Spruiell, J.A. Scott, C.S. Ary, R.L. Hardin: Metall. Trans., 1973, vol. 4, pp. 1533–4410.1007/BF02668005 ↗
25. J.M. Vitek, S.A. David: Weld. J., 1986, vol. 65 (4), pp. 106s–111s
26. B. Weiss, R. Stickler: Metall. Trans., 1972, vol. 3, pp. 851–6610.1007/BF02647659 ↗
27. T.D. Anderson: The Influence of Molybdenum on the Microstructure of Stainless Steel Welds, Lehigh University, Bethlehem, PA, 2005, p. 31
28. J.N. DuPont, J.R. Michael, C.V. Robino: Weld. J., 2000, vol. 79 (3), pp. 43–48
29. D.J. Prior, P.W. Trimby, U.D. Weber, D.J. Dingley: Mineralog. Mag., 1996, vol. 60 (403), pp. 859–6910.1180/minmag.1996.060.403.01 ↗
30. T. Hahn: International Tables for Crystallography, Kluwer, 1996
31. PDF4, International Center for Diffraction Data, Newtown Square, PA, 2006
32. J.W. Elmer, S.M. Allen, T.W. Eagar: Metall. Trans. A, 1989, vol. 20A, pp. 2117–3110.1007/BF02650298 ↗
33. J.N. DuPont, C.V. Robino, A.R. Marder, M.R. Notis: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2797–280610.1007/s11661-998-0320-x ↗
34. S. Katayama and A. Matsunawa: in ICALEO, Laser Institute of America, Orlando, FL, 1984
35. J.W. Elmer: The Influence of Cooling Rate on the Microstructure of Stainless Steel Alloys, Massachusetts Institute of Technology, Cambridge, MA, 1988, pp. 1–38810.2172/5678406 ↗
36. J.A. Brooks, F.J. Lambert Jr.: Weld. J., 1978, vol. 57 (5), pp. 139s–143s
37. J.W. Elmer et al.: in The Metal Science of Joining, TMS, Warrendale, PA, 1992, pp. 123–33
38. J.A. Brooks, J.C. Williams, A.W. Thompson: Metall. Trans. A, 1983, vol. 14A, pp. 1271–8110.1007/BF02664809 ↗
39. M.J. Perricone: in Materials Science and Engineering, Lehigh University, Bethlehem, PA, 2005, p. 197
40. P.W. Fuerschbach: Sandia Optimization and Analysis Routines. Sandia National Laboratories, Albuquerque, NM, 2003
41. B. Sundman: Thermo-Calc 2001, KTH, Stockholm, 2001
42. B. Sundmann, B. Jansson, J.O. Andersson: CALPHAD, 1985, vol. 9, p. 15310.1016/0364-5916(85)90021-5 ↗
43. N. Saunders: Fe-Data Thermodynamic Database, ThermoTech Ltd., The Surrey Research Park, Guildford, United Kingdom, 2001
44. T.D. Anderson, J.N. DuPont, M.J. Perricone, A.R. Marder: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 86–9910.1007/s11661-006-9010-8 ↗
45. S. Heino: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1893–190510.1007/s11661-000-0217-9 ↗
46. A.V. Kington, F.W. Noble: Mater. Sci. Technol., 1995, vol. 11 (3), pp. 268–7510.1179/mst.1995.11.3.268 ↗
47. Y. Maehara, N. Fujino, T. Kunitake: ISIJ, 1983, vol. 23 (3), pp. 247–5510.2355/isijinternational1966.23.247 ↗
48. W. Reick, M. Pohl, A.F. Padilha: ISIJ Int., 1998, vol. 38 (6), pp. 567–7110.2355/isijinternational.38.567 ↗
49. M.J. Perricone et al. Materials Science & Technology, TMS, Cincinnati, OH, 2006
50. H. Inoue, T. Koseki, S. Ohkita, M. Fuji: Weld. Int., 1998, vol. 12 (4), pp. 282–9610.1080/09507119809448487 ↗
51. S.A. David, J.M. Vitek, T.L. Hebble: Weld. J., 1987, vol. 66 (10), pp. 289s–300s
52. J.M. Vitek, S.A. David, C.R. Hinman: Weld. J., 2003, vol. 82 (1), pp. 10s–17s
53. R.A. Farrar: J. Mater. Sci., 1985, vol. 20, pp. 4215–3110.1007/BF00552417 ↗
54. P.K. Koh: J. Met., 1953 vol. 2, pp. 339–43
55. J.K.L. Lai: Mater. Sci. Eng., 1983, vol. 58, pp. 195–20910.1016/0025-5416(83)90046-0 ↗
56. Y. Minami, H. Kimura, Y. Ihara: Mater. Sci. Technol., 1986, vol. 2 (8), pp. 795–80610.1179/mst.1986.2.8.795 ↗
57. H.C. Vacherm, C.J. Bechtoldt: J. Res. Nat. Bur. Stand., 1954, vol. 53 (2), pp. 67–7610.6028/jres.053.008 ↗
58. N. Saunders: JMatPro. 2005, Sente Software, Guildford, United Kingdom
59. X. Li, A.P. Miodownik, N. Saunders: Mater. Sci. Technol., 2002, vol. 18 (8), pp. 861–6810.1179/026708302225004694 ↗
60. S. Heino, E.M. Knutson-Wedel, B. Karlsson: Mater. Sci. Technol., 1999, vol. 15 (1), pp. 101–0810.1179/026708399773003376 ↗
61. M.J. Cieslak, A.M. Ritter, W.F. Savage: Weld. J., 1984, vol. 63 (4), pp. 133s–140s
62. Y. Song, N.A. McPherson, T.N. Baker: ISIJ Int., 1996, vol. 36 (11), pp. 1392–9610.2355/isijinternational.36.1392 ↗
63. T. Chandra, R. Kuchlmayr: J. Mater. Sci., 1988, vol. 23, pp. 723–2810.1007/BF01174712 ↗
64. Y. Maehara, M. Koike, N. Fujino, T. Kunitake: ISIJ, 1983, vol. 23 (3), pp. 240–4610.2355/isijinternational1966.23.240 ↗
65. R. Magnabosco, N. Alonso-Falleiros: Corrosion, 2005, vol. 61 (2), pp. 130–3610.5006/1.3278167 ↗
66. A.F. Padilha, W. Reick, F.C.J. Pimenta: Z. Metallkd., 2001, vol. 92 (4), pp. 351–54
67. S.H.C. Park et al. Scripta Mater., 2003, vol. 49, pp. 1175–8010.1016/j.scriptamat.2003.08.022 ↗
68. A. Poznansky and P.J. Grobner: in New Developments in Stainless Steel Technology, ASM International, Materials Park, OH, 1985, pp. 195–206
69. S. Nenno, M. Tagaya, K. Hosomi, Z. Nishiyama: Trans. Jpn. Inst. Metall., 1963, vol. 13, p. 1159
70. S. Nenno, M. Tagaya, Z. Nishiyama: Trans. Jpn. Inst. Metall., 1962, vol. 4, p. 22210.2320/matertrans1960.4.222 ↗
71. A.C. Lewis, J.F. Bingert, D.J. Rowenhorst, A. Gupta, A.B. Geltmachen, G. Spanos: Mater. Sci. Eng., 2006, vol. A418, pp. 11–1810.1016/j.msea.2005.09.088 ↗
72. J.M. Vitek, S.A. David, M.J. Cieslak, J.H. Perepezko, S. Kang, M.E. Glicksman: The Metal Science of Joining, Cincinnati, OH, 1992, pp. 115–22
73. A.L. Schaeffler: Met. Progr., 1949, vol. 56 (11), pp. 680B–680B
74. C.N. McCowan, T.A. Siewert, D.L. Olson: Weld. Res. Counc., 1989, vol. (342), pp. 1–36
75. D.L. Olson: Weld. Res. (Miami), 1985, Oct., pp. 281s–295s
76. E.O. Hall, S.H. Algie: Metall. Rev., 1966, vol. 11, pp. 61–8810.1179/imr.1966.11.1.61 ↗
77. J.S. Kasper: Acta Metall., 1954, vol. 2 (5), pp. 456–6110.1016/0001-6160(54)90066-8 ↗