journal article·2011-12

Welding-Induced Microstructure Evolution of a Cu-Bearing High-Strength Blast-Resistant Steel

Jeremy L. Caron, Sudarsanam Suresh Babu, John C. Lippold

Publisher page

Abstract

A new high strength, high toughness steel containing Cu for precipitation strengthening was recently developed for naval, blast-resistant structural applications. This steel, known as BlastAlloy160 (BA-160), is of nominal composition Fe-0.05C-3.65Cu-6.5Ni-1.84Cr-0.6Mo-0.1V (wt pct). The evident solidification substructure of an autogenous gas tungsten arc (GTA) weld suggested fcc austenite as the primary solidification phase. The heat-affected zone (HAZ) hardness ranged from a minimum of 353 HV in the coarse-grained HAZ (CGHAZ) to a maximum of 448 HV in the intercritical HAZ (ICHAZ). After postweld heat treatment (PWHT) of the spot weld, hardness increases were observed in the fusion zone (FZ), CGHAZ, and fine-grained HAZ (FGHAZ) regions. Phase transformation and metallographic analyses of simulated single-pass HAZ regions revealed lath martensite to be the only austenitic transformation product in the HAZ. Single-pass HAZ simulations revealed a similar hardness profile for low heat-input (LHI) and high heat-input (HHI) conditions, with higher hardness values being measured for the LHI samples. The measured hardness values were in good agreement with those from the GTA weld. Single-pass HAZ regions exhibited higher Charpy V-notch impact toughness than the BM at both test temperatures of 293 K and 223 K (20 °C and –50 °C). Hardness increases were observed for multipass HAZ simulations employing an initial CGHAZ simulation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (59)

Show source-provided references
1. M.D. Uchic: J. Mater., 2006, vol. 58 p. 24.
2. G. Spanos: Scripta Mater., 2006, vol. 55, p. 3.10.1016/j.scriptamat.2006.02.038 ↗
3. G. Spanos, A.B. Geltmacher, A.C. Lewis, J.F. Bingert, M. Mehl, D. Papaconstantopoulos, Y. Mishin, A. Gupta, and P. Matic: Mater. Sci. Eng. A, 2007, vols. 452–453, pp. 558–68.10.1016/j.msea.2006.10.110 ↗
4. A. Saha and G.B. Olson: J. Comput.-Aided Mater. Des., 2007, vol. 14, pp. 177–200.10.1007/s10820-006-9031-z ↗
5. A. Saha, J. Jung, and G.B. Olson: J. Comput.-Aided Mater. Des., 2007, vol. 14, pp. 201–33.10.1007/s10820-006-9032-y ↗
6. Adv. Mater. Processes, 2004, vol. 162 (12), pp. 9–10.
7. J. Huergo: Office of Naval Research Press Release, Office of Naval Research, Arlington, VA, 2004.
8. M.D. Mulholland and D.N. Seidman: Scripta Mater., 2009, vol. 60, pp. 992–95.10.1016/j.scriptamat.2009.02.033 ↗
9. Ø. Grong: Metallurgical Modelling of Welding, 2nd ed., The Institute of Materials, Cambridge, United Kingdom, 1997, pp. 4–14.
10. K. Easterling: Introduction to the Physical Metallurgy of Welding, Butterworth-Heinemann, Oxford, United Kingdom, 1992, pp. 126–27.10.1016/B978-0-7506-0394-2.50008-3 ↗
11. G. Spanos, R.W. Fonda, R.A. Vandermeer, and A. Matuszeski: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 3277–93.10.1007/BF02669455 ↗
12. M. Shome, O.P. Gupta, and O.N. Mohanty: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 985–96.10.1007/s11661-004-0025-8 ↗
13. W. Sperko: Weld J., 2005, vol. 84, pp. 37–40.
14. B.T. Alexandrov and J.C. Lippold: Weld. World, 2007, vol. 51, pp. 48–59.10.1007/BF03266608 ↗
15. Standard Practice for Quantitative Measurement and Reporting of Hypoeutectoid Carbon and Low-Alloy Steel Phase Transformations, ASTM Designation A 1033–04, ASTM, West Conshohocken, PA, 2004.
16. T. Kop, J. Sietsma, and S. Van der Zwaag: J. Mater. Sci., 2001, vol. 36, pp. 519–26.10.1023/A:1004805402404 ↗
17. Standard Test Methods for Notched Bar Impact Testing of Metallic Materials, ASTM Designation E 23–07, West Conshohocken, PA, 2007.
18. G.E. Lucas, G.R. Odette, J.W. Sheckherd, P. McConnell, and J. Perrin: The Use of Small-Scale Specimens for Testing Irradiated Material, ASTM STP 888, Philadelphia, PA, 1986, pp. 305–24.10.1520/STP33012S ↗
19. W.R. Corwin and A.M. Hougland: The Use of Small-Scale Specimens for Testing Irradiated Material, ASTM STP 888, Philadelphia, PA, 1986, pp. 325–38.10.1520/STP888-EB ↗
20. G.F. Vander Voort: Metallography: Principles and Practice, ASM INTERNATIONAL, Materials Park, OH, 1999, p. 638.
21. A.K. De, J.G. Speer, and D.K. Matlock: Adv. Mater. Processes, 2003, vol. 161, pp. 27–30.
22. Standard Test Methods for Determining Average Grain Size, ASTM Designation E 112–96, ASTM, West Conshohocken, PA, 1996.
23. Standard Test Method for Microindentation Hardness of Materials, ASTM Designation E 384–08, ASTM, West Conshohocken, PA, 2008.
24. J.C. Lippold and D.J. Kotecki: Welding Metallurgy and Weldability of Stainless Steels, John Wiley & Sons, Hoboken, NJ, 2005, p. 154.
25. B. Sundman, B. Jansson, and J.-O. Andersson: CALPHAD, 1985, vol. 9, pp. 153–90.10.1016/0364-5916(85)90021-5 ↗
26. J.C. Lippold, W.A. Baeslack, and I. Varol: Weld. J., 1992, vol. 71, pp. 1s–14s.
27. C.S. Smith and E.W. Palmer: Trans. TMS-AIME, 1933, vol. 105, pp. 133–68.
28. E. Hornbogen and R.C. Glenn: Trans. TMS-AIME, 1960, vol. 218, pp. 1064–70.
29. S.R. Goodman, S.S. Brenner, and J.R. Low: Metall. Trans., 1973, vol. 4, pp. 2363–69.10.1007/BF02669376 ↗
30. S.R. Goodman, S.S. Brenner, and J.R. Low: Metall. Trans., 1973, vol. 4, pp. 2371–78.10.1007/BF02669377 ↗
31. M.S. Gagliano and M.E. Fine: Metall. Mater. Trans. A, 2004, vol. 27A, pp. 2323–29.10.1007/s11661-006-0212-x ↗
32. G. Eldis: Hardenability Concepts with Applications to Steel, AIME, New York, NY, 1978, pp. 126–57.
33. G. Krauss: Steels: Processing, Structure, and Performance, ASM INTERNATIONAL, Materials Park, OH, 2005, p. 64.
34. H.-S. Yang and H.K.D.H. Bhadeshia: Scripta Mater., 2009, vol. 60, pp. 493–95.10.1016/j.scriptamat.2008.11.043 ↗
35. X. Yu, J.L. Caron, S.S. Babu, J.C. Lippold, D. Isheim, and D.N. Seidman: Acta Mater., 2010, vol. 58, pp. 5596–5609.10.1016/j.actamat.2010.06.031 ↗
36. J.P. Naylor: Metall. Trans. A, 1979, vol. 10A, pp. 861–73.10.1007/BF02658305 ↗
37. K.C. Russell and L.M. Brown: Acta Metall., 1972, vol. 20, pp. 969–74.10.1016/0001-6160(72)90091-0 ↗
38. H. Lippard: Ph.D. Dissertation, Northwestern University, Evanston, IL, 1999.
39. A. Saha: Ph.D. Dissertation, Northwestern University, Evanston, IL, 2004.
40. S.S. Babu, M.L. Santella, X. Yu, J.L. Caron, and E.D. Specht: The Ohio State University, Columbus, OH, unpublished research, 2010.
41. S.S Babu, E.D. Specht, S.A. David, J. Karapetrova, P. Zschak, M. Peet, and H.K.D.H. Bhadeshia: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 985–96.
42. X. Yu, S.S. Babu, J.C. Lippold, H. Terasaki, and Y. Komizo: Metall. Mater. Trans. A, 2011, vol. 42A, DOI:10.1007/s11661-011-0746-4.10.1007/s11661-011-0746-4 ↗
43. G. Krauss: Steels: Processing, Structure, and Performance, ASM INTERNATIONAL, Materials Park, OH, 2005, pp. 184–94.
44. P.L. Harrison and R.A. Farrar: Int. Mater. Rev., 1989, vol. 34, pp. 35–51.10.1179/imr.1989.34.1.35 ↗
45. M. Shome and O.N. Mohanty: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2159–69.10.1007/BF02586136 ↗
46. N. Saunders, Z. Guo, X. Li, A.P. Miodownik, and J.-P. Schillé: J. Mater., 2003, vol. 55, pp. 60–65.
47. N. Saunders, Z. Guo, X. Li, A.P. Miodownik, and J.-P. Schillé: The Calculation of TTT and CCT Diagrams for General Steels, Thermotech, Guildford, United Kingdom.
48. J.S. Kirkaldy, B.A. Thomson, and E.A. Baganis: Hardenability Concepts with Applications to Steel, AIME, New York, NY, 1978, pp. 82–125.
49. Atlas of Isothermal Transformation Diagrams of B.S. En Steels, Iron and Steel Institute, London, 1956.
50. H.E. Boyer: Atlas of Isothermal and Cooling Transformation Diagrams, ASM, Metals Park, OH, 1977.
51. M. Atkins: Atlas of Continuous Cooling Transformation Diagrams for Engineering Steels, ASM, Metals Park, OH, 1977.
52. S.-K. Hwang, J. Sungho, and J.W. Morris: Metall. Trans. A, 1975, vol. 6A, pp. 2015–21.10.1007/BF03161826 ↗
53. J.I. Kim and J.W. Morris: Metall. Trans. A, 1980, vol. 11A, pp. 1401–06.10.1007/BF02653495 ↗
54. H. Nakagawa, T. Miyazaki, and H. Yokota: J. Mater. Sci., 2000, vol. 35, pp. 2245–53.10.1023/A:1004778910345 ↗
55. J.I. Kim and J.W. Morris: Metall. Trans. A, 1981, vol. 12A, pp. 1957–63.10.1007/BF02643809 ↗
56. J.I. Kim, C.K. Syn, and J.W. Morris: Metall. Trans. A, vol. 14A, pp. 93–103.10.1007/BF02643742 ↗
57. L.-Å. Norström and O. Vingsbo: Met. Sci., 1979, vol. 13, pp. 677–84.10.1179/030634579790434321 ↗
58. W.C. Leslie: The Physical Metallurgy of Steels, Hemisphere Publishing Corporation, New York, NY, 1981, pp. 302–03.
59. C. Wang, M. Wang, J. Shi, W. Hui, and H. Dong: Scripta Mater., 2008, vol. 58, pp. 492–95.10.1016/j.scriptamat.2007.10.053 ↗