Effect of Process Parameters on Microstructure and Hardness of Oxide Dispersion Strengthened 18Cr Ferritic Steel
Source abstract
Abstract
Pre-alloyed ferritic 18Cr steel (Fe-18Cr-2.3W-0.3Ti) powder was milled with and without nano-yttria in high-energy ball mill for varying times until steady-state is reached. The milled powders were consolidated by upset forging followed by hot extrusion. Microstructural changes were examined at all stages of processing (milling, upset forging, and extrusion). In milled powders, crystallite size decreases and hardness increases with increasing milling time reaching a steady-state beyond 5 hours. The size of Y2O3 particles in powders decreases with milling time and under steady-state milling conditions; the particles either dissolve in matrix or form atomic clusters. Upset forged sample consists of unrecrystallized grain structure with few pockets of fine recrystallized grains and dispersoids of 2 to 4 nm. In extruded and annealed rods, the particles are of cuboidal Y2Ti2O7 at all sizes and their size decreased from 15 nm to 5 nm along with significant increase in number density. The oxide particles in ODS6 are of cuboidal Y2Ti2O7 with diamond cubic crystal structure (Fd $$ \bar{3} $$ m) having a lattice parameter of 10.1 A and are semicoherent with the matrix. The hardness values of extruded and annealed samples predicted by linear summation model compare well with measured values.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fusion materials and technologies · Nuclear Materials and Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. S. Ukai and M. Fujiwara: J. Nucl. Mater., 2002, vol. 307–311, pp. 749–57.10.1016/S0022-3115(02)01043-7 ↗
2. S.J. Zinkle and J.T. Busby: Mater. Today, 2009, vol. 12, pp. 12–19.10.1016/S1369-7021(09)70294-9 ↗
3. S. Ukai, S. Mizuta, T. Yoshitake, T. Okuda, M. Fujiwara, S. Hagi, and T. Kobayashi: J. Nucl. Mater., 2000, vol. 283–287, pp. 702–06.10.1016/S0022-3115(00)00114-8 ↗
4. A. Alamo, V. Lambard, X. Averty, and M.H. Mathon: J. Nucl. Mater., 2004, vol. 329–333, pp. 333–37.10.1016/j.jnucmat.2004.05.004 ↗
5. M.K. Miller, D.T. Hoelzer, E.A. Kenik, and K.F. Russell: Intermetallics, 2005, vol. 13, pp. 387–92.10.1016/j.intermet.2004.07.036 ↗
6. R.L. Klueh, J.P. Shingledecker, R.W. Swindeman, and D.T. Hoelzer: J. Nucl. Mater., 2005, vol. 341, pp. 103–14.10.1016/j.jnucmat.2005.01.017 ↗
7. T. Jayakumar, M.D. Mathew, and K. Laha: Procedia Eng., 2013, vol. 55, pp. 259–70.10.1016/j.proeng.2013.03.252 ↗
8. 8.S. Ohtsuka, S. Ukai, M. Fujiwara, T. Kaito, and T. Narita: Mater. Trans., 2005, vol. 46, pp. 487–92.10.2320/matertrans.46.487 ↗
9. S. Ukai: Compr. Nucl. Mater., 2012, vol. 4, pp. 241–71.10.1016/B978-0-08-056033-5.00069-0 ↗
10. G.R. Odette, M.J. Alinger, and B.D Wirth: Annu. Rev. Mater. Res., 2008, vol. 38, pp. 471–503.10.1146/annurev.matsci.38.060407.130315 ↗
11. M. Ratti, D. Leuvrey, M.H. Mathon, and Y. de Carlan: J. Nucl. Mater., 2009, vol. 386–388, pp. 540-43.10.1016/j.jnucmat.2008.12.171 ↗
12. S. Ohtsuka, S. Ukai, M. Fujiwara, T. Kaito, and T. Narita: J. Phys. Chem. Solids, 2005, vol. 66, pp. 571–75.10.1016/j.jpcs.2004.06.033 ↗
13. S. Ohtsuka, S. Ukai, M. Fujiwara, T. Kaito, and T. Narita: J. Nucl. Mater., 2004, vol. 329–333, pp. 372–76.10.1016/j.jnucmat.2004.04.043 ↗
14. P. Dou, A. Kimura, R. Kasada, T. Okuda, M. Inoue, S. Ukai, S. Ohnuki, T. Fujisawa, and F. Abe: J. Nucl. Mater., 2013, vol. 442, pp. S95–-S100.10.1016/j.jnucmat.2013.04.090 ↗
15. M. Ohnuma, J. Suzuki, S. Ohtsuka, S.-W. Kim, T. Kaito, M. Inoue, and H. Kitazawa: Acta Mater., 2009, vol. 57, pp. 5571–81.10.1016/j.actamat.2009.07.054 ↗
16. R. Schaublin, A. Ramar, N. Baluc, V. de Castro, M.A. Monge, T. Leguey, N. Schmid, and C. Bonjour, J. Nucl. Mater., 2006, vol. 351, pp. 247–60.10.1016/j.jnucmat.2006.02.005 ↗
17. A. Kimura, H.-S. Cho, N. Toda, R. Kasada, K. Yutani, H. Kishimoto, N. Iwata, S. Ukai, and M. Fujiwara: J. Nucl. Sci. Technol., 2007, vol. 44, pp. 323–28.10.1080/18811248.2007.9711289 ↗
18. B. Dousti, R. Mojaver, H.R. Shahverdi, and R.S. Mamoory: J. Alloy. Compd., 2013, vol. 577, pp. 409-16.10.1016/j.jallcom.2013.05.201 ↗
19. A. Pandey, K. Jayasankar, P. Parida, M. Debata, B.K. Mishra, and S. Saroja, Powder Technol., 2014, vol. 262, pp. 162–6910.1016/j.powtec.2014.04.070 ↗
20. Z. Dapeng, L. Yong, L. Feng, W. Yuren, Z. Liujie, and D. Yuhai: Mater. Lett., 2011, vol. 65, pp. 1672–74.10.1016/j.matlet.2011.02.064 ↗
21. Y. Liu, J. Fang, D. Liu, Z. Lu, F. Liu, S. Chen, and C.T. Liu: J. Nucl. Mater., 2010, vol. 396, pp. 86–93.10.1016/j.jnucmat.2009.10.057 ↗
22. P. Dou, A. Kimura, T. Okuda, M. Inoue, S. Ukai, S. Ohnuki, T. Fujisawa, and F. Abe: J. Nucl. Mater., 2011, vol. 417, pp. 166–70.10.1016/j.jnucmat.2011.01.061 ↗
23. S. Ukai, T. Nishida, H. Okada, T. Okuda, M. Fujiwara, and K. Asabe: J. Nucl. Sci. Technol., 1997, vol. 34, pp. 256–63.10.1080/18811248.1997.9733658 ↗
24. R. Delhez, T.H. Keijser, J.I. Langford, D. Louer, E.J. Mittemeijer, and E.J. Snneveld: The Rietveld Method, Oxford University Press, Oxford, 1993, pp. 132–65.10.1093/oso/9780198555773.003.0008 ↗
25. R. Vijay, M. Nagini, J. Joardar, M. Ramakrishna, A.V. Reddy, and G. Sundararajan: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 1611–20.10.1007/s11661-012-1494-9 ↗
26. M. Nagini, R. Vijay, M. Ramakrishna, A.V. Reddy, and G. Sundararajan: Mater. Sci. Eng. A, 2015, vol. 620, pp. 490–99.10.1016/j.msea.2014.10.050 ↗
27. J. Wosik, B. Dubial, A. Kruk, H.J. Penkalla, F. Schubert, and A.C. Filemonowicz: Mater. Charact., 2001, vol. 46, pp. 119–23.10.1016/S1044-5803(01)00112-7 ↗
28. D.B. Williams and C.B. Carter: Transmission Electron Microscopy, Plenum Press, New York, 1996.10.1007/978-1-4757-2519-3 ↗
29. C. Suryanarayana: Prog. Mater. Sci., 2001, vol. 46, pp. 1–184.10.1016/S0079-6425(99)00010-9 ↗
30. B.S. Murty and S. Ranganathan: Int. Mater. Rev., 1998, vol. 43, pp. 101–144.10.1179/imr.1998.43.3.101 ↗
31. J. Gil Sevillano, P. van Houtte, and E. Aernoudt: Prog. Mater. Sci., 1981, vol. 25, pp. 69–412.10.1016/0079-6425(80)90001-8 ↗
32. H. Zhang, M.J. Gorley, K.B. Chong, M.E. Fitzpatrick, S.G. Roberts, and P.S. Grant: J. Alloy. Compd., 2014, vol. 582, pp. 769–73.10.1016/j.jallcom.2013.08.069 ↗
33. C.A. Williams, P. Unifantowicz, N. Baluc, G.D.W. Smith, and E.A. Marquis: Acta Mater., 2013, vol. 61, pp. 2219–35.10.1016/j.actamat.2012.12.042 ↗
34. G. Ressel, S. Primig, and H. Leitner: Int. J. Mater. Res., 2013, vol. 104, pp. 1088–95.10.3139/146.110964 ↗
35. M.L. Brocq, F. Legendre, M.-H. Mathon, A. Mascaro, S. Poissonnet, B. Radiguet, P. Pareige, M. Loyer, and O. Leseigneur: Acta Mater., 2012, vol. 60, pp. 7150–59.10.1016/j.actamat.2012.09.024 ↗
36. 36.M.C. Brandes, L. Kovarik, M.K. Miller, and M.J. Mills: J. Mater. Sci., 2012, vol. 47, pp. 3913–23.10.1007/s10853-012-6249-x ↗
37. C.A. Williams, G.D.W. Smith, and E.A. Marquis: Scripta Mater., 2012, vol. 67, pp. 108–11.10.1016/j.scriptamat.2012.03.035 ↗
38. Z. Oksiuta, P. Kozikowski, M. Lewandowska, M. Ohnuma, K. Suresh, and K.J. Kurzydlowski: J. Mater. Sci., 2013, vol. 48, pp. 4620–25.10.1007/s10853-013-7255-3 ↗
39. J. Ribis and Y. de Carlan: Acta Mater., 2012, vol. 60, pp. 238–52.10.1016/j.actamat.2011.09.042 ↗
40. A. Hirata, T. Fujita, Y.R. Wen, J.H. Schneibel, C.T. Liu, and M.W. Chen: Nat. Mater., 2011, vol. 10, pp. 922–26.10.1038/nmat3150 ↗
41. P. Olier, J. Malaplate, M.H. Mathon, D. Nunes, D. Hamon, L. Toualbi, Y. de Carlan, and L. Chaffron: J. Nucl. Mater., 2012, vol. 428, pp. 40–46.10.1016/j.jnucmat.2011.10.042 ↗
42. J. Ribis, M.-L. Lescoat, S.Y. Zhong, M.-H. Mathon, and Y. de Carlan: J. Nucl. Mater., 2013, vol. 442, pp. S101–05.10.1016/j.jnucmat.2012.10.051 ↗
43. Z. Oksiuta, M. Lewandowska, and K.J. Kurzydłowski: Mech. Mater., 2013, vol. 67, pp. 15–24.10.1016/j.mechmat.2013.07.006 ↗
44. R. Vijay, M. Nagini, S.S. Sarma, M. Ramakrishna, A.V. Reddy, and G. Sundararajan: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 777–84.10.1007/s11661-013-2019-x ↗
45. J.H. Kim, T.S Byun, D.T. Hoelzer, C.H. Park, J.T. Yeom, and J.K. Hong: Mater. Sci. Eng. A, 2013, vol. 559, pp. 111–18.10.1016/j.msea.2012.08.041 ↗